爆炸复合接头剪切强度测试方法研究

参照正交各向异性层压复合板层间剪切强度的测试方法,提出了用于测试爆炸复合接头复合界面剪切强度的3种方法;并建立三维有限元模型,分别对3种测试方法进行模拟;最后分别对3种方法进行了测试试验.结果表明,3种试验方法均能有效测试爆炸复合接头的剪切强度,其中对称试件双切口拉伸法最适合实际应用.     

基于退化速率跟踪粒子滤波的剩余使用寿命预测框架

毋庸置疑,剩余使用寿命预测对于设备的健康管理越来越重要。近年来粒子滤波方法被越来越多地应用到设备寿命预测技术当中,这是因为粒子滤波方法能更好的解决非线性非高斯系统滤波问题,而且能够获得不确定度信息。但该方法的预测性能却过度依赖于预测模型,并且对于模型参数的初始分布也比较敏感,这在一定程度上限制了粒子滤波预测方法的进一步发展。本文针对基本粒子滤波预测方法的不足,提出了一种基于退化速率跟踪粒子滤波的通用预测框架,以历史观测数据的退化速率统计规律作为指导来跟踪目标数据的退化速率,实现对粒子滤波预测方法的简化。并将该方法用于轴承和锂离子电池的剩余使用寿命预测,验证了方法的有效性。     

基于自适应阈值的FAST特征点提取算法

FAST特征提取算法阈值选取固定,因此不能满足不同图像的特征点抽取要求,并且提取的结果存在着多个特征点块的现象。针对这些缺陷,首先采用动态全局阈值对原始灰度图像进行初步提取得到候选特征点,然后采取动态局部阈值和非极大值抑制法进一步对候选特征点进行筛选,从而达到自适应选取阈值和抑制多个特征点块的目的。实验表明,改进后的算法稳定性高,对不同光照和对比度情况下有一定的适应能力,并且运算量相对比于其他一些特征提取算法要小得多,满足实时应用的要求。     

Thermal hazard assessment of TKX-50-based melt-cast explosive

In the present study, thermal hazards of TNT and DNAN used as the molten binder in TKX-50-based melt-cast explosives were comparatively studied through accelerating rate calorimeter (ARC) and Cook-off experiments. Two kinds of ARC operation modes were performed to investigate the thermal safety performance under adiabatic conditions (HWS mode) and constant heating (CHR mode). The obtained results demonstrated that at both heating modes, DNAN/TKX-50 outperformed TNT/TKX-50 from the thermal safety point of view. However, the sensitivity to heat of the samples was reverse because of the different heating modes. In addition, the results of thermal hazard assessment obtained from the cook-off experiment complied with ARC analysis which indicated the molten binder TNT replaced by DNAN would reduce the hazard of the TKX-50 melt cast explosive. Furthermore, the results of cook-off experiments also showed that DNAN/TKX-50 outperformed TNT/TKX-50 from the aspect of thermal stability, which was consistent with the result of CHR mode because of the similar heating process.     

Formation of adiabatic shearing band for high-strength Ti-5553 alloy: A dramatic thermoplastic microstructural evolution

By using split Hopkinson pressure bar, optical microscopy and electronic microscopy, we investigate the influence of initial microstructures on the adiabatic shear behavior of high-strength Ti–5Al–5V–5Mo–3Cr (Ti-5553) alloy with lamellar microstructure and bimodal microstructure. Lamellar alloy tends to form adiabatic shearing band (ASB) at low compression strain, while bimodal alloy is considerably ASB-resistant. Comparing with the initial microstructure of Ti-5553 alloy, we find that the microstructure of the ASB changes dramatically. Adiabatic shear of lamellar Ti-5553 alloy not only results in the formation of recrystallized β nano-grains within the ASB, but also leads to the chemical redistribution of the alloying elements such as Al, V, Cr and Mo. As a result, the alloying elements distribute evenly in the ASB. In contrast, the dramatic adiabatic shear of bimodal alloy might give rise to the complete lamination of the globular primary α grain and the equiaxial prior β grain, which is accompanied by the dynamic recrystallization of α lamellae and β lamellae. As a result, ASB of bimodal alloy is composed of α/β nano-multilayers. Chemical redistribution does not occur in ASB of bimodal alloy. Bimodal Ti-5553 alloy should be a promising candidate for high performance armors with high mass efficiency due to the processes high dynamic flow stress and excellent ASB-resistance.     

轴向剪切条件下功能梯度圆柱形复合材料的界面开裂问题研究

针对外覆功能梯度涂层的圆柱形复合材料在轴向剪切作用下的界面开裂问题,建立了断裂力学分析的理论模型。运用分离变量和无穷级数法,推导了奇异积分方程;利用Lobatto-Chebyshev配点法将其离散为代数方程组,最后得到了应力强度因子的数值解。对数值结果的讨论表明:在涂层外表面固定的条件下,可以通过降低涂层厚度和设计内侧软而外侧硬的涂层2种途径来有效地减小界面的断裂驱动力。研究结果可为工程中该类复合材料的防断裂优化设计提供理论参考。     

基于应变局部化理论的剑桥模型改进

应用传统的弹塑性理论模型在分析剪切带的时候遇到了很多困难,如控制方程失去椭圆性等,其原因是传统的弹塑性理论模型并没有包含材料的内部参数。在剑桥模型的基础上,考虑应变二阶梯度,提出一种新的计算剪切带的理论模型。当应变局部化发生时,带内土体采用该模型计算,带外土体则按照传统弹塑性模型计算。该理论模型汲取了剑桥模型实验参数少,应用简便的优点。     

纤维缠绕复合材料夹芯圆柱体高应变率压缩吸能机理

为研究纤维缠绕复合材料夹芯圆柱体吸能元件在高应变率冲击压缩载荷作用下的变形损伤模式和能量吸收机理,采用ABAQUS商用有限元软件和分离式Hopkinson压杆装置开展数值模拟分析和试验验证研究。对比分析宏观力学响应规律和微观损伤破坏机理,可知吸能结构元件在高应变率压缩载荷下的力学响应具有典型的弹塑性特征,内部芯材主要产生压缩塑性损伤,而表层复合材料沿环向产生拉伸断裂破坏。研究表明,该吸能元件冲击压缩吸能特性优异,可满足水下结构平台的冲击防护和浮力储备要求。     

流的大小与传输速率相结合的双门限检测算法

提出基于流传输速率与数据量的双门限检测算法。为满足高速网络传输的性能要求,使用Hash表存储流检测的数据结构,将Hash表的冲突处理与基于流速率的缓存替换相结合以实现高效的大流检测,通过限制Hash桶的容量,确保报文的处理性能。真实网络数据的仿真测试结果表明:所提算法在相近的存储开销下,保持了较高的处理性能,准确性优于基于最近最少使用算法的大流检测及其派生算法以及基于统计计数的紧凑型空间节省算法。