炸药装药在压剪加载下的起爆特点

进行了两类压剪加载实验：（１）利用石英的平面正碰撞产生压剪加载的实验,采用电磁质速法测试装药试件内部不同质点的运动情况,分析炸药装药中发生化学反应的可能性;（２）在压剪炮上采用平行倾斜碰撞产生压剪加载的实验,观测炸药装药爆炸的可能性。由实验可以看出：在亚爆轰状态的压缩加载应力条件下,剪切的联合作用对炸药的起爆起到敏化作用,适当比例的压剪加载造成更加敏感的炸药起爆响应。文中给出了起爆响应规律和响应机制的实验分析。     

Shaped charge penetration into high- and ultrahigh-strength Steel–Fiber reactive powder concrete targets

Experiments on shaped charge penetration into high and ultrahigh strength steel-fiber reactive powder concrete (RPC) targets were performed in this paper. Results show that the variation of penetration depth and crater diameter with concrete strength is different from that of shaped charge penetration into normal strength concrete (NSC). The crater diameter of RPC is smaller than that of NSC penetrated by the shaped charge. The jet particles are strongly disturbed and hardly reach the crater bottom because they pass through the narrow channel formed by jet penetration into the RPC. The effects of radial drift velocity and gap effects of jet particles for a shaped charge penetration into RPC target are discussed. Moreover, a theoretical model is presented to describe the penetration of shaped charge into RPC target. As the concrete strength increases, the penetration resistance increases and the entrance crater diameter decreases. Given the drift velocity and narrow crater channel, the low-velocity jet particles can hardly reach the crater bottom to increase the penetration depth. Moreover, the narrow channel has a stronger interference to the jet particles with increasing concrete strength; hence, the gap effects must be considered. The drift velocity and gap effects, which are the same as penetration resistance, also have significant effects during the process of shaped charge penetration into ultrahigh-strength concrete. The crater profiles are calculated through a theoretical model, and the results are in good agreement with the experiments.     

Numerical simulation of the blast wave of a multilayer composite charge

The numerical simulation of a blast wave of a multilayer composite charge is investigated. A calculation model of the near-field explosion and far-field propagation of the shock wave of a composite charge is established using the AUTODYN finite element program. Results of the near-field and far-field calculations of the shock wave respectively converge at cell sizes of 0.25–0.5 cm and 1–3 cm. The Euler––flux-corrected transport solver is found to be suitable for the far-field calculation after mapping. A numerical simulation is conducted to study the formation, propagation, and interaction of the shock wave of the composite charge for different initiation modes. It is found that the initiation mode obviously affects the shock-wave waveform and pressure distribution of the composite charge. Additionally, it is found that the area of the overpressure distribution is greatest for internal and external simultaneous initiation, and the peak pressure of the shock wave exponentially decays, fitting the calculation formula of the peak overpressure attenuation under different initiation modes, which is obtained and verified by experiment. The difference between numerical and experimental results is less than 10%, and the peak overpressure of both internal and external initiation is 56.12% higher than that of central single-point initiation.     

电荷泵中单粒子瞬变的研究

为分析电荷泵中不同频率单粒子瞬变(SET)电流对锁相环(PLL)的影响,采用频域分析法从增益和带宽的角度研究了环路参数与SET响应的关系。分析结果表明,减小环路滤波电阻可以降低系统增益,从而有效降低压控振荡器控制电压的扰动;增大固有频率或阻尼因子则可以提高系统带宽,从而滤除更大范围的SET电流,同时还可以降低PLL恢复到锁定状态的时间。因此,减小环路滤波电阻、增大固有频率或阻尼因子是有效的设计加固方法。通过1GHz PLL的SET模拟验证了上述结论。     

关于小尺寸装药用炸药薄膜的研究

利用真空蒸镀技术对太安炸药薄膜及其在小尺寸装药上的应用进行了研究。实验表明利用真空蒸镀技术可以研制出性能优良的炸药薄膜 ;红外光谱分析证明太安在蒸镀前后没有发生质的变化 ;扫描电镜分析得出了太安薄膜的微观结构 ;太安炸药薄膜在小尺寸装药上的应用表明了该装药具有可靠的传爆功能。     

装甲车辆自动装弹机的现状及未来

自动装弹机己在各国新一代装甲车辆上得到广泛应用。通过阐述在装甲车辆上采用自动装弹机的优点和必要性,介绍了现阶段自动装弹机的几种实现方式及其优缺点,并对自动装弹机的未来发展做出了展望。     

聚能射流侵彻下舰船钢与均质钢的等效关系

基于剩余穿深理论,依据聚能射流对钢靶板侵彻毁伤作用机理,推导出2种等效模型,并结合数值模拟建立了聚能射流侵彻下某舰船装甲钢与603钢靶板的等效关系。结果表明:当舰船钢厚度较小时,舰船钢与603装甲钢的等效厚度比约为1;当舰船钢厚度较大时,两者等效厚度比约为1.13。由此等效关系可给出用于战斗部考核性穿靶试验中相应均质靶板的确定厚度,从而为用603装甲钢靶代替该舰船钢进行聚能射流威力考核试验提供依据,达到了简化、经济、方便、有效的目的。     

双层柱壳的流固耦合模态计算与试验研究

采用结构有限元和内域流体有限元的流固耦合计算方法,对球壳及其内域流体进行有限元离散计算,并将计算所得的模态振动频率与理论结果进行了比较.采用同样的方法,进一步对加筋双层圆柱壳进行了流固耦合的复特征值分析,并求解了其固有频率和振型.试验分别对双层柱壳充水和不充水情况下模态和模态频率进行了测量,结果证实了数值计算方法的正确性.     

薄壳变速箱壳体动态响应仿真分析与试验验证

在ADAMS（Automatic Dynamic Analysis of Mechanical Systems）中搭建薄壳箱体的刚柔耦合虚拟仿真模型,进行动态响应仿真分析。在相同试验条件下,搭建薄壳箱体动态响应试验台架,并进行动态振动试验。利用Q-400非接触式测试系统测量台架试验结果。对比仿真分析和试验测量结果,验证了仿真分析模型的准确性和计算结果的可靠性。     

iSIGHT在多目标优化问题中的应用研究

在工程实际中,随着设计要求的日益提高,单一的设计目标已经不能满足设计者的要求。于是多目标设计优化问题在设计领域越来越占据主导地位。目前多目标优化设计方法种类繁多,各有优劣,重点介绍优化设计框架iSIGHT,并就iSIGHT在解决鱼雷壳体结构设计中的多目标优化设计问题中的应用情况进行研究,讨论iSIGHT在解决多目标优化问题中的可行性。