基于MIMO技术的山体滑坡雷达

现有山体滑坡雷达是轨道式的,这样就需要精确控制雷达的运动来获得高方位向分辨率,因此,硬件设备要求极高。利用多输入多输出(MIMO)技术通过分时发射和接收信号来获取高方位向分辨率,可以免去雷达运动,从而简化了雷达设备和降低雷达成本。此外,结合步进频连续波技术可以使山体滑坡雷达保持高距离向分辨率的同时进一步降低对硬件的要求,更易于工程实现,成本更低。通过MATLAB仿真初步验证了该方案的可行性。     

平底气泡船凹槽气层波动特性

为提高大型平底气泡船底部凹槽设计的有效性,基于RANS方程及VOF两相流模型构建了大型平板船凹槽气层数值计算模型。研究气层在凹槽中的动态发展过程,分析速度对气层波动的影响规律,并阐述三维凹槽气层的波形特性及其与二维气层波动的区别,揭示气层波动的相似律。数值结果表明:气层在凹槽中呈现波动形态,气层波长随速度的增加而增大,波长等于速度平方的0.64倍;气层在凹槽侧壁的干扰及反射下呈现相干波系,从而其波高及局部厚度也随之改变;气层波动满足傅汝德相似。     

基于空域相关滤波的雷达回波信号降噪方法

对雷达探测来说,如何有效地增强真实目标回波信号、提高信噪比水平是非常重要的。传统的降噪方法如平滑滤波、傅立叶降噪很难有效地降低与目标频谱相重叠的噪声。空域相关滤波算法是小波滤波算法中的一种,能够有效地解决这个问题。该算法是利用真实信号与噪声在尺度间的不同表现来实现的,能够在保留信号细节的同时,有效地降低噪声。仿真表明,该算法在雷达回波的降噪中取得了较好效果,有效地降低了噪声。     

柔性长鳍扭波推进数学模型分析

以"尼罗河魔鬼"鱼的柔性长背鳍扭波推进模式为研究对象,通过观察活鱼的游动模式,提取影响扭波推进的运动学要素,建立了描述柔性长背鳍扭波推进时动态曲面的数学模型。研究了鳍条仰角与摆动规律对鳍面的影响。最后,用细长体理论分析并计算出推力分布。研究表明,鳍条仰角在φ=85°的情况下所形成的鳍面与垂直鳍条所形成的鳍面相比,其最大偏离值与鳍长之比为1.7%,可以用垂直于基线的鳍条制作模型;鳍条按正弦规律摆动时所形成的扭波波形鳍面与实鱼鳍面相似。     

面内阶跃载荷下薄板弹性动力屈曲差分解

根据薄板微元的动力平衡分析导出薄板动力屈曲控制方程,由屈曲瞬间能量转换率守恒条件得出一个压缩波前屈曲变形的附加约束方程,由此得到求解薄板动力屈曲问题的完备定解条件.以受载边夹支的薄板为倒,利用有限差分法得出了薄板前三阶动力屈曲模态和相应的两个特征参数值,并对比分析了薄板静、动力屈曲的差别.分析表明,薄板动力屈曲过程中产生屈曲动能,比静力屈曲要吸收更多的外部能量.     

锥形液膜的Kelvin-Helmholtz扰动波

为进行锥形液膜雾化过程分析,研究锥形液膜的Kelvin-Helmholtz稳定性问题,应用小扰动假设,建立了锥形液膜数学模型、轴对称扰动运动的控制方程和边界条件,采用分离变量法求解线性偏微分扰动方程组,经过严格的数学推导,得到了锥形液膜内外表面扰动波增长速率特征方程.当液膜锥角为零时,与环形液膜扰动波特征方程一致;当液膜锥角和液膜内径为零时,与圆射流扰动波特征方程一致,表明导出的锥形液膜扰波动方程是合理的.     

Modeling of the whole process of shock wave overpressure of free-field air explosion

The waveform of the explosion shock wave under free-field air explosion is an extremely complex problem. It is generally considered that the waveform consists of overpressure peak, positive pressure zone and negative pressure zone. Most of current practice usually considers only the positive pressure. Many empirical relations are available to predict overpressure peak, the positive pressure action time and pressure decay law. However, there are few models that can predict the whole waveform. The whole process of explosion shock wave overpressure, which was expressed as the product of the three factor functions of peak, attenuation and oscillation, was proposed in the present work. According to the principle of explosion similarity, the scaled parameters were introduced and the empirical formula was absorbed to form a mathematical model of shock wave overpressure. Parametric numerical simulations of free-field air explosions were conducted. By experimental verification of the AUTODYN numerical method and comparing the analytical and simulated curves, the model is proved to be accurate to calculate the shock wave overpressure under free-field air explosion. In addition, through the model the shock wave overpressure at different time and distance can be displayed in three dimensions. The model makes the time needed for theoretical calculation much less than that for numerical simulation.     

BDS/INS紧组合三频动对动模糊度解算方法

针对伪距观测噪声较大导致动对动条件下三频整周模糊度解法(Three Carrier Ambiguity Resolution, TCAR)模糊度解算不可靠的问题,提出了一种BDS/INS紧组合三频动对动整周模糊度解算方法。通过紧组合系统输出的高精度位置坐标,估算出双差几何距离值,并用其分别代替无几何和几何模式下的双差伪距观测值,显著降低了伪距双差观测噪声水平,有效提高了三频整周模糊度解算成功率。仿真实验结果表明,BDS/INS紧组合输出的高精度位置坐标使得伪距观测精度提高了60%以上,在短基线条件下,当伪距观测噪声达到2 m时,无几何模式下的TCAR算法模糊度解算成功率为0.73%,几何模式下的TCAR算法模糊度解算成功率为31.25%,而BDS/INS紧组合的TCAR算法在两种模式下的模糊度解算成功率达到99%以上,并且获得了厘米级的相对定位精度。     

A fast-running method for blast load prediction shielding by a protective barrier

This study presents a simplified blast load prediction method on structures behind a protective barrier. The proposed method is basically an empirical approach based on Kingery-Bulamsh (K-B) chart and finite element (FE) analysis results. To this end, this study divides the structure into three regions by three critical points. Blast loads at each critical point can be calculated based on K-B chart and an approximation according to FE analysis results. Finally, peak reflected overpressure and impulse distributed on the structure can be approximately estimated by linearly connecting blast loads at each critical point. In order to confirm a feasibility of the proposed method, a series of numerical simulations were carried out. The simulation results were compared with FE analysis results which are presented in the open literature. From such comparisons, it was found that the proposed method is applicable to predict blast loads on structures behind a protective barrier.     

Experimental study of transient pressure wave in the behind armor blunt trauma induced by different rifle bullets

Pressure wave plays an important role in the occurrence of behind armor blunt trauma (BABT), and ballistic gelatin is widely used as a surrogate of biological tissue in the research of BABT. Comparison of pressure wave in the gelatin behind armor for different rifle bullets is lacking. The aim of this study was to observe dynamic changes in pressure wave induced by ballistic blunt impact on the armored gelatin block and to compare the effects of bullet type on the parameters of the transient pressure wave. The gelatin blocks protected with National Institute of Justice (NIJ) class III bulletproof armor were shot by three types of rifle bullet with the same level of impact energy. The transient pressure signals at five locations were recorded with pressure sensors and three parameters (maximum pressure, maximum pressure impulse, and the duration of the first positive phase) were determined and discussed. The results indicated that the waveform and the twin peak of transient pressure wave were not related to the bullet type. However, the values of pressure wave’s parameters were significantly affected by bullet type. Additionally, the attenuation of pressure amplitude followed the similar law for the three ammunitions. These findings may be helpful to get some insight in the BABT and improve the structure design of bullet.