Thermal hazard assessment of TKX-50-based melt-cast explosive

In the present study, thermal hazards of TNT and DNAN used as the molten binder in TKX-50-based melt-cast explosives were comparatively studied through accelerating rate calorimeter (ARC) and Cook-off experiments. Two kinds of ARC operation modes were performed to investigate the thermal safety performance under adiabatic conditions (HWS mode) and constant heating (CHR mode). The obtained results demonstrated that at both heating modes, DNAN/TKX-50 outperformed TNT/TKX-50 from the thermal safety point of view. However, the sensitivity to heat of the samples was reverse because of the different heating modes. In addition, the results of thermal hazard assessment obtained from the cook-off experiment complied with ARC analysis which indicated the molten binder TNT replaced by DNAN would reduce the hazard of the TKX-50 melt cast explosive. Furthermore, the results of cook-off experiments also showed that DNAN/TKX-50 outperformed TNT/TKX-50 from the aspect of thermal stability, which was consistent with the result of CHR mode because of the similar heating process.     

Analysis on damage characteristics and detonation performance of solid rocket engine charge subjected to jet

To further explore the damage characteristics and impact response of the shaped charge to the solid rocket engine (SRE) in storage or transportation, protective armor was designed and the shelled charges model (SCM)/SRE with protective armor impacting by shaped charge tests were conducted. Air overpressures at 5 locations and axial acceleration caused by the explosion were measured, and the experimental results were compared with two air overpressure curves of propellant detonation obtained by related scholars. Afterwards, the finite element software AUTODYN was used to simulate the SCM impacted process and SRE detonation results. The penetration process and the formation cause of damage were analyzed. The detonation performance of TNT, reference propellant, and the propellant used in this experiment was compared. The axial acceleration caused by the explosion was also analyzed. By comprehensive comparison, the energy released by the detonation of this propellant is larger, and the HMX or Al particles contained in this propellant are more than the reference propellant, with a TNT equivalent of 1.168–1.196. Finally, advanced protection armor suggestions were proposed based on the theory of woven fabric rubber composite armor (WFRCA).     

基于ANSYS的油罐拱顶稳定性分析

针对加肋拱顶稳定性十分复杂的问题,基于ANSYS建立了加肋拱顶油罐的三维有限元模型,对加肋拱顶的结构稳定性进行了数值模拟。对加肋拱顶在外压作用下的线性与非线性临界屈曲载荷进行了对比分析,利用弧长法获得了拱顶在加肋情况下径向、环向、轴向的载荷-位移曲线。结果表明:数值模拟的加肋拱顶屈曲方向和屈曲区域与实际失稳结果相一致,可以为加肋拱顶设计和稳定性分析提供一定参考。     

钢丝增强复合条带抗弹性能数值分析

为研究钢丝增强聚合物基复合条带的抗弹性能,基于冲击动力学理论分析其抗弹机理,再借助ANSYS/LS-DYNA软件和LS-PrePost前后处理器模拟有无增强钢丝2种工况下,条带对7.62 mm弹体的冲击响应。分析表明：条带的弹性模量、剪切模量和面密度会影响其能量吸收性能,能量吸收量随三者的增大而增大;由于聚合物基体的正交各向异性,应力云图显示出扁平椭圆状是合理的;在聚合物基复合条带中嵌入增强钢丝对条带整体的抗弹性能有积极的影响,但嵌入过量的钢丝会导致重量和成本的增加,因此需要对合理的钢丝配比率作进一步研究。研究结果可为钢丝增强聚合物基复合条带在野战防护结构中的应用提供参考。     

影响油罐电位的输油参数分析

目前,油库、储运公司改扩建工程较多,不可避免对工艺流程进行调整,依据液体静电产生原理,应用高斯定理和欧姆定律等理论,分析油罐注油过程中油面电位以及时间与管径、流速等各参数之间的关系,针对管径不变流速变化的情况,进行实验分析,在不对管路进行整改,仅对泵进行重新设计优选时,对如何控制罐内电位的安全,提出参考方案,对油库改扩建工程有一定的指导意义。     

基于振动烈度的柴油机供油系统断油故障检测方法

研究了振动烈度的相关方法和理论,以WD615柴油机供油系断油故障诊断为例,通过各缸断油时振动烈度值与正常状态下振动烈度值的比较分析,验证了利用振动烈度进行发动机供油系统故障诊断方法的正确性。     

发动机配气机构振动信号时域分析

对康明斯6BT5.9型柴油发动机配气机构产生的振动信号进行了时域分析,采用振动加速度峰峰值作为判定发动机配气机构技术状态的特征量,并采用多通道信息融合技术实现配气机构的故障诊断。     

嵌入式实时操作系统性能测试方法

为综合评价操作系统能否满足使用要求,研究了一种定量测试嵌入式实时操作系统功能和性能的方法,提出了具体的测试项目、测试环境和测试用例的要点,给出一种基于外部注入的功能测试、性能测试、应用测试方法及具体实现。测试结果证明,该方法对提高软件质量,缩短研制周期,增强可维护性等方面有显著效果。     

坦克装甲车辆火控技术的现状及发展

对坦克火控系统的技术现状和发展前景进行了较为详尽的论述,并指出了当前国内火控发展中面临的主要技术难题及解决办法.     

主战坦克作战效能分析与模糊综合评价

主战坦克是我军地面战的重要武器,长期以来其作战效能的评价都采用单一的指标,无法全面、准确地进行评价。通过对影响主战坦克作战效能各因素的全面分析,建立了主战坦克作战效能综合评价的指标体系,并以模糊综合评价为手段,应用模糊集合和模糊数学,建立了主战坦克作战能力的综合评价与分析模型,并给出计算实例与分析。研究结果对全面而科学地评价坦克作战效能具有积极的指导作用和较强的实用性。