超急速温升下丙酮液池的温度场计算

通过实验和数值模拟计算 ,研究了瞬时、强热流极端条件下铂薄膜表面覆盖和不覆盖细小金属颗粒时丙酮液体和金属颗粒温度场分布及其变化规律 .确定了温升速率、温度梯度和温度边界层厚度 ,发现了常规沸腾难以解释的现象 ,并指出覆盖金属颗粒后虽然沸腾极为激烈 ,但难以达到极高的温升速率 ,而不覆盖金属颗粒却容易产生爆发沸腾     

Effect of particle gradation of aluminum on the explosion field pressure and temperature of RDX-based explosives in vacuum and air atmosphere

To optimize the energy output and improve the energy utilization efficiency of an aluminized explosive, an explosion device was developed and used to investigate the detonation pressure and temperature of R1 (Al6) aluminum powder and the aluminum powder particle gradation of R2 (Al6+Al13), R3 (Al6+Al24) and R4 (Al6+Al flake) in a confined space. By using gas chromatography, quantitative analysis and calculations were carried out to analyze the gaseous detonation products. Finally, the reaction ratios of the aluminum powder and the explosion reaction equations were calculated. The results show that in a confined space, the quasi-static pressures and equilibrium temperature of the aluminum powder in air are higher than in vacuum. In vacuum, the quasi-static pressures and equilibrium temperatures of the samples in descending order are R1>R3>R4>R2 and R3>R4>R1>R2, respectively. In air, the quasi-static pressures and equilibrium temperatures of the samples in descending order are R1>R2>R4>R3 and R1>R4>R2>R3, respectively. R4 (Al6+Al flake) and R3 (Al6+Al24) have relatively higher temperatures after detonation, which shows that the particle gradation method can enhance the reaction energy output of aluminum during the initial reaction stage of the explosion and increase the reaction ratio by 10.6% and 8.0%, respectively. In air, the reaction ratio of Al6 aluminum powder can reach as high as 78.16%, and the reaction ratio is slightly reduced after particle gradation. Finally, the reaction equations of the explosives in vacuum and in air were calculated by quantitative analysis of the explosion products, which provides a powerful basis for the study of RDX-based explosive reactions.     

温度对舰船阴极保护和腐蚀静电场的影响

海水中氧溶解量和海水电导率是影响海水腐蚀性能的重要因素,而这两个因素主要取决于海水的盐度和温度。采用边界元法建立舰船外加电流阴极保护和腐蚀静电场模型,研究不同海水温度下氧溶解量、电导率及氧的扩散系数对舰船腐蚀防腐静电场的影响。结果表明,腐蚀电场峰值随着温度的升高而减小,当两对阳极输出电流分别为13.5 A和8 A时,船体和舵在低温处于过保护状态而在高温处于欠保护状态,螺旋桨和轴在不同温度下均能得到较好的保护。     

LaB6空心阴极中毒特性

LaB_6阴极与其他类型阴极相比具有电子发射电流密度大等优点,已广泛用于电推进、高发射密度电子枪等产品。为了研究LaB_6空心阴极中毒特性、识别LaB_6空心阴极主要失效模式,分别对LaB_6空心阴极暴露大气后性能变化特征和引起性能变化的原因进行了研究。结果表明:LaB_6空心阴极在暴露大气后表面吸附大量中毒气体,出现了发射体表面逸出功增加、发射体短期中毒现象。此时空心阴极的放电电压和阴极顶温度均有所上升,经过短期工作后放电电压和阴极顶温度均恢复初始状态。但LaB_6空心阴极严重中毒后,并不能通过加热和离子轰击方式去除表面生成的氧化物。因此,可以在实验过程中通过监测空心阴极的阴极顶温度和阳极电压变化间接表征空心阴极发射体状态。     

Effect of bending temperatures on the microstructure and springback of a TRIP steel sheet

Transformation-induced plasticity (TRIP) steel possesses high strength and formability, enabling the use of a thinner gauge material and allowing for the fabrication of complex shapes. In this research, we measured the effect of bending temperatures on the microstructure and air-bending springback angle of TRIP steel at temperatures from 25 to 600 °C. Real-time in situ X-ray diffraction and scanning electron microscopy were used for pre- and postbending analysis. As the prebending temperature increased from 25 °C to 600 °C, the retained austenite (RA) volume fraction decreased, and the RA transformed to bainite at temperatures above 400 °C. The springback angle was positively correlated with the prebending RA volume fraction, with the smallest springback angle achieved at 400 °C. Additionally, the springback angle was positively correlated with the bending angle, because the RA transformation ratio contributed to increased strain hardening. Further microstructure analysis revealed that the RA became elongated in the tension direction as the bending temperatures increased.     

收缩管道装置层流热边界层理论及应用研究

研究了收缩管道装置层流热边界层理论及其应用。对于速度边界层提出了相似性解的解析结果,给出了速度分布、边界层厚度、摩擦阻力和水头损失的解析计算表达式。对于温度边界层利用管道热边界层方程,推出了温度分布、温度边界层厚度和热流量的计算关系式,并给出了设计应用实例。     

基于经典控制理论的制导系统校正方法研究

针对空空导弹抗目标大机动时,制导系统持续增加的快速性需求,利用反馈/前馈控制信号可提高瞬态和频率响应的经典控制思想,以及在制导算法中引入导弹的实际加速度补偿量以改善制导回路性能的方法,设计了制导系统校正算法.然后,通过线性化模型对制导系统校正算法的性能进行了数字仿真,仿真结果表明系统校正算法能够降低目标机动时所产生的脱...     

炉温对化学气相沉积SiC涂层组成及显微结构的影响

采用SEM、EDX、XRD测试手段对沉积炉壁产物进行了分析,结果表明:低温区沉积的SiC涂层全为β SiC;高温区SiC涂层中含有少量的游离态Si和α SiC;高温区SiC颗粒的形核和生长速率大于低温区;所以温度是影响化学气相沉积SiC涂层组成及显微结构的主要因素。     

基于合成孔径原理目标散射测量中的运动误差补偿

在应用基于合成孔径原理的水下目标散射特性测量新方法时,目标总会存在偏离匀速直线的运动误差,导致图像散焦甚至无法成像,从而不能得到目标二维散射特性.针对上述问题,从水下目标的六自由度运动误差入手,分析运动误差对成像的影响,采用基于运动测量系统的逐点运动补偿方法对回波信号进行处理,给出了计算机仿真试验结果.仿真试验得到了较好的成像结果,验证了运动补偿的有效性.     

模糊控制在循环流化床锅炉床温控制系统中的应用研究

由于循环流化床锅炉床温控制系统具有大滞后、多变量、强耦合等非线性特性,其控制系统比较复杂。为了解决复杂控制系统难以控制的问题,采用模糊控制理论进行锅炉床温控制系统的设计,并应用MATLAB软件对模糊控制系统进行仿真。仿真实验结果表明,与传统的PID相比,采用模糊控制策略,系统的响应速度快,控制精度高。