返回舱垂直着陆过程动力学研究

在考虑着陆场地面弹塑性特点的情况下,建立了返回舱垂直着陆过程的弹塑性接触模型。数值分析结果表明,返回舱的着陆过程与地面土壤的物理性质有很大关系,在相同的弹性模量下,土壤的极限应力越大,则着陆过载最大值就越大,着陆过程中的能量损失就越小,返回舱的"跳跃"现象越明显。     

载体干扰磁场补偿方法

获得载体航行路径上各点地磁场的精确测量值是地磁匹配导航的前提,而载体上各种干扰磁场的存在会引起磁力仪输出的偏差,影响匹配的精度,因此必须对载体干扰磁场进行补偿。在分析载体干扰磁场特性的基础上,提出利用矢量测量值对地磁场总场值进行补偿的方法。该方法首先根据矢量磁力仪的测量模型得到关于载体磁场参数的非线性方程,然后采用非线性参数估计方法估计出精确的载体干扰磁场系数,最后再利用估计结果对测量值进行补偿。通过仿真对该方法的有效性进行研究,并设计了半实物实验对其实用性进行验证。结果表明采用本文提出的方法补偿后地磁场总场值的测量误差在20nT以内,而且该方法参数估计精度高,应用方便,可以有效地对导航载体干扰磁场进行补偿。     

火灾时公路隧道排烟方案设计与优选

针对双车道单向行驶高速公路隧道火灾提出三种排烟方案.利用FDS软件数值模拟火灾时各方案对烟气迁移和温度分布的影响,最后优选火灾时的排烟方案.结果表明：三种方案均能起到很好的排烟效果.若不考虑成本及技术难度,组合排烟方式效果最佳;若考虑成本和技术难度,则设置排烟口排烟效果最佳.在实际隧道发生火灾时,应综合考虑决定选取哪一种方案.若选用组合排烟方式,笔者建议火灾时,火源上游仅开启射流风机,火源下游则应同时开启排烟口,这样既节约成本,又能达到目的.     

罐顶板声发射检测及其稳定最不利点有限元分析

罐顶板的缺陷检测对于评估立式拱顶罐的使用状况有着重要的意义,它的应用有助于更好地掌握立式拱顶罐的安全状况与可靠程度。将声发射法应用于罐顶板材料的检测,并对相关的设备仪器及操作流程进行介绍。为了给检测结果提供对照和参考,利用有限元分析法对拱顶瓜皮板的稳定最不利点进行了初步分析和定位。分析结果表明：顶板中上部肋板围成的区域可能会产生稳定最不利点,该部位应作为检测时重点关注的区域。     

油库压缩机组温度变送器法兰根部泄漏失效分析

为了解决基地油库压缩机组温度变送器法兰根部焊缝泄漏问题,采用照相、无损检测、化学成分分析、金相分析、显微硬度分析、扫描电镜观察与能谱分析等方法,对失效法兰进行失效分析。研究结果表明,法兰焊缝根部泄漏系焊缝未焊透和存在夹杂物所致,并因外应力作用而在熔合区马氏体区域沿晶扩展,导致角焊缝最终脆性断裂。结合现场实际情况,提出防止发生类似事故的建议。     

Screening multi-dimensional heterogeneous populations for infectious diseases under scarce testing resources,with application to COVID-19

Testing provides essential information for managing infectious disease outbreaks, such as the COVID-19 pandemic. When testing resources are scarce, an important managerial decision is who to test. This decision is compounded by the fact that potential testing subjects are heterogeneous in multiple dimensions that are important to consider, including their likelihood of being disease-positive, and how much potential harm would be averted through testing and the subsequent interventions. To increase testing coverage, pooled testing can be utilized, but this comes at a cost of increased false-negatives when the test is imperfect. Then, the decision problem is to partition the heterogeneous testing population into three mutually exclusive sets: those to be individually tested, those to be pool tested, and those not to be tested. Additionally, the subjects to be pool tested must be further partitioned into testing pools, potentially containing different numbers of subjects. The objectives include the minimization of harm (through detection and mitigation) or maximization of testing coverage. We develop data-driven optimization models and algorithms to design pooled testing strategies, and show, via a COVID-19 contact tracing case study, that the proposed testing strategies can substantially outperform the current practice used for COVID-19 contact tracing (individually testing those contacts with symptoms). Our results demonstrate the substantial benefits of optimizing the testing design, while considering the multiple dimensions of population heterogeneity and the limited testing capacity.     

BaGa4Se7与KTiOAsO4光参量振荡输出3.5 μm激光性能对比

为对比新型非线性晶体BaGa₄Se₇(简称 BGSe)和成熟商用非线性晶体KTiOAsO₄(简称 KTA) 所输出的中红外激光性能,使用1.06 μm激光泵浦BGSe(56.3°,0°,type-Ⅰ)和KTA(90°, 0°,type-Ⅱ-A)输出3.5 μm激光。在泵浦光波长为1 064 nm、脉宽为13 ns、光斑直径为4 mm、光参量振荡腔长为90 mm的条件下,实验测得KTA(L=20 mm)和BGSe(L=15 mm)的泵浦振荡阈值分别为52.6 mJ(理论值为46.11 mJ)和20.6 mJ(理论值为18.32 mJ);BGSe输出波长与温度的变化率Δλ₂/ΔT为3.20 nm/℃(理论值为2.49 nm/℃),KTA的Δλ₂/ΔT为0.073 nm/℃(理论值为0.077 nm/℃);实验测得BGSe的输出线宽为4.71 nm,KTA为2.45 nm。BGSe和KTA的泵浦阈值和温度调谐在理论和实验上吻合得较好,且结果表明:BGSe在这两个方面优于KTA;但KTA在输出窄线宽方面优于BGSe晶体。实验结果表明,BGSe是一种具有广泛应用前景的中远红外非线性晶体。     

Ablation characteristics of insulator under high-temperature gas dual-pulse erosion

This study numerically simulated and investigated the flow field characteristics of a typical dual-pulse solid rocket motor with a soft pulse separation device through thermal insulation ablation under high-temperature dual-pulse erosion. The ablation rate of ethylene -propylene-diene monomer (EPDM) insulator was measured after the experiment. Experimental results were analyzed through scanning electron microscopy and microcomputed tomography. The ablation mechanism of the EPDM insulator under the operation conditions of a dual-pulse solid rocket motor was evaluated by analyzing the results. The results reveal that the internal flow field of the motor with a soft pulse separation device is uniform. The original charred layer existing on the EPDM insulator surface in the first pulse combustor is the decisive factor affecting the final ablation rate of the dual-pulse motor during the second pulse operation, and the ablation characteristic region is easily formed with the exfoliation of the charred layer. The ablation rate difference of the insulator increases with gas velocity.     

近界视景导航中森林场景加速绘制

作为近界视景导航中典型地物,三维几何树模型能提高虚拟场景视觉精度,增强场景真实感,但会导致大规模森林场景绘制效率降低,从而降低视景导航精度。为提高绘制效率以确保视景导航精度,并提高场景真实感,采用布告板云算法构建了基于视距的多分辨率树模型,针对算法在近界视景导航应用中存在的问题进行了改进。为进一步提高近界特别是贴地飞行时高动态视点下视景导航精度,根据有限视域、威胁区域以及视觉冗余等特点,提出了一种基于高动态视点的加速绘制算法。通过实验对比分析,算法大幅提高了场景绘制效率,增强了场景视觉质量,提高了虚拟场景导航精度。     

铜冶炼炉溜槽上方钢梁温度分布研究

为了对有色冶炼厂房框架钢梁耐火稳定性评估提供条件,根据冶炼铜实际工况建立计算模型,数值研究钢梁温度分布,结果表明:在加热初期,钢梁的平均温度和最高温度不断上升,经历10个升温-降温周期后,钢梁的最高温度稳定在220℃左右。钢梁温度与梁的截面尺寸和形状、梁计算截面位置、溜槽与梁相对位置等众多因素有关。梁与溜槽距离越大,梁截面高度越大,翼缘宽度越小,最高温度与平均温度越低;梁长度大小不影响梁最高温度,但梁长度越大平均温度越低。