NICALON SiC/Al 预制丝热膨胀特性研究

本文研究了NICALON SiC束丝纤维增强铝预制丝在15～400℃温度区间内的热膨胀特性。研究表明预制丝两次热循环后得到的膨胀曲线不一致,该曲线在15～400℃范围的平均热膨胀系数分别为3.2×10~(-6)℃~(-1)、4.1×10~(-6)℃~(-1)。本文对预制丝的热膨胀行为进行了理论分析和探讨,计算值和实验值较为符合。     

超低频拖曳磁场天线设计中的热噪声研究

通过对产生超低频拖曳磁场天线热噪声的原理以及各种天线构造参数对热噪声影响的研究,得出了在电缆浮力条件下保证最小热噪声ENF的最优化基本参数的表达式.结合对天线其它电参数的要求,探讨了利用最优化参数的可行性.分析结果表明,获得高可逆磁导率的磁芯是实现最优化参数的关键,并给出了解决这一问题的途径.     

位移不连续法在裂纹扩展仿真中的应用

探讨了在应用位移不连续法仿真裂纹扩展时对加载方式、裂纹扩展长度及应力强度因子计算等问题的处理方法,并据此编制了仿真程序,分析了裂纹在单向压载作用下的扩展趋势和应力变化,具有一定的工程应用价值。     

大口径火炮身管热弯曲计算与试验

建立火炮在阳光照射下身管上下表面温度场、热弯曲及炮口角的计算模型。以某大口径长身管火炮为实例,计算该炮的炮口弯曲量与炮口角,进行自然阳光照射与环境模拟条件下的热弯曲试验,验证计算模型与计算结果的正确性与可信性;提出通过测量身管上下表面温度快速求取火炮身管不同环境温度及温差下的弯曲量与炮口角的工程应用方法。     

超音速气流中热塑性复合材料壁板的非线性热颤振特性

热塑性复合材料结构在高速流场中的颤振行为是可重复使用航天器设计中需要考虑的问题.基于Mindlin厚板理论和Von-Karman大变形理论描述热塑性复合壁板结构大变形,超音速气动力采用活塞气动理论.考虑温度引起的壁板面内热应力和热塑性材料力学性能的改变.根据虚功原理和有限元法推导建立了热塑性复合材料壁板的热颤振模型,进...     

Influences of different crossing types on dynamic response of underground cavern subjected to ground shock

An intersecting cavern is a common structural form used in underground engineering, and its safety and stability performance directly control the service performance of the whole project. The dynamic re-sponses of the three kinds of crossing type (+-shaped, T-shaped, L-shaped) caverns subjected to ground shock were studied by numerical simulation. The velocity plus force mode boundary setting method was proposed in the coupled static and dynamic analysis of a deep underground cavern. The results show that, among the three types of crossing caverns, the+-shaped cavern is the most significantly affected by the dynamic action, followed by T-shaped, and then L-shaped caverns. The vault settlement, straight wall deformation, vault peak particle velocity, effective plastic strain of surrounding rock, and maximum principal stress and strain at the bottom of the lining of the straight wall increase with the increase of cavern span. The vault settlement, straight wall deformation, effective plastic strain of surrounding rock, and the maximum principal stress and strain at the bottom of lining to the straight wall decrease with the increase of lateral pressure coefficient, and the peak particle velocity at the vault increases. The variation is small compared with the change of cavern span. The influence range of the underground cavern intersection is two cavern diameters from the intersection centre. The bottom of the straight wall at the intersection is the weak part. It is suggested to thicken the support locally to improve the stability of the cavern.     

Effect of friction stir processing on mechanical properties and heat transfer of TIG welded joint of AA6061 and AA7075

Tungsten inert gas (TIG) welding is the most commonly used joining process for aluminum alloy for AA6061 and AA7075 which are highly demanded in the aerospace engineering and the automobile sector, but there are some defects occur during TIG welding like micro-crack, coarse grain structure, and porosity. To improve these defects, the TIG welded joint is processed using friction stir processing (FSP). This paper presents the effect of friction stir processing on TIG welding with filler ER4043 and ER 5356 for dissimilar aluminum alloy AA6061 and AA7075. The mechanical characterization, finite element formulation and mathematical equations of heat transfer of TIG + FSP welded joints are investigated using ANSYS Fluent software by adjusting process parameters of FSP. The results show that the maximum compressive residual stress 73 MPa was obtained at the fusion zone (FZ) of the TIG weldment with filler ER4043, whereas minimum compressive residual stress 37 MPa was obtained at stir zone (SZ) of the TIG+FSP with filler 5356. The maximum heat flux 5.33 × 106 W/m2 and temperature 515 ℃ have observed at tool rotation 1600 rpm with a feed rate of 63 mm/min. These results give a satisfactory measure of confidence in the fidelity of the simulation     

自润滑弹带挤进过程中渗出油量的对比计算

从弹带的作用及特性出发, 通过数值计算和统计计算 2种方法计算了自润滑弹带挤进过程中的渗出油量,初步得出了渗出油量和行程之间的关系。这一问题的解决为自润滑弹带材料的选择提供了理论依据。通过对 2种算法的比较可知, 数值计算误差更小一些, 而统计计算对数学条件要求不太苛刻。     

大功率消磁线圈受力分析与计算

大功率消磁线圈在运行中会受到较强电磁力的作用,客观地分析和计算电磁力的大小及分布情况,是设计和建造大型消磁站的一项基础性的工作.文中从电磁场基本原理出发,应用张量理论分析、计算了大功率消磁线圈的受力情况,对于设计和建造大型消磁站具有参考作用.     

某型飞机平尾轴疲劳断裂失效分析

采用台架试验装置对某型飞机平尾轴进行了疲劳试验,通过断口的观察分析、断口部位的金相分析、硬度检测、有限元结构应力分析,确定了平尾轴的失效模式,并对其断裂失效原因进行了分析。结果表明：平尾轴的断裂性质为疲劳断裂,裂纹源均起源于大轴简体内壁加工刀痕形成的沟槽处,变截面圆弧造成的结构应力集中和粗糙加工刀痕形成的附加应力集中是造成大轴疲劳断裂的主要原因。关键词：平尾轴;疲劳断裂;失效分析;应力集中