Effects of nano-sized aluminum on detonation characteristics and metal acceleration for RDX-based aluminized explosive

Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the param-eters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0％to 15％,every 5％increase of aluminum resulted in about a 1.3％decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14％and 8％higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 μs throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12％and 2.9 μs higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80％of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.     

带有氧化钨涂层的ITO平面电极在LB系列电解液中的阻抗分析

电致变色实验显示1 mol/L六氟磷酸锂与碳酸乙烯酯、碳酸二甲酯、碳酸二乙酯和碳酸甲乙酯所混合形成的电解液(LB)系列是一类非常节能的电致变色电解液,它们能用很小的充电电流(20μA/cm2)使得氧化钨薄膜获得更长久、更好的变色性.研究氧化钨薄膜在LB系列电解液中的交流阻抗特性,有助于更好地理解氧化钨薄膜的变色性能.文中研究了带有氧化钨薄膜层的ITO平面电极处于LB系列电解液中的阻抗谱,分别得出了氧化钨薄膜和ITO电极的等效电路;测算出氧化薄膜的常相位角元件、薄膜电阻、韦伯电阻以及与ITO电极有关的电双层电容和电极电荷转移电阻.证实了LB315是性能优良的电解液.     

非局部薄板动力学特性分析的广义有限积分变换方法

基于应力梯度非局部薄板理论模型,推导了非局部薄板动力学特性求解的广义有限积分变换方法.通过选取适应边界条件的积分核函数并构建广义积分变换对,应用积分变换将非局部薄板的高阶偏微分方程变换成线性方程组,直接求解得到固有频率.将广义有限积分变换方法的计算结果和有限元法及已有文献的结果进行对比,验证了本文方法的正确性.在此基础...     

15000m~3钢板贴壁油罐建设静态投资分析

以部队某保障基地油库军用柴油扩容工程采用钢板贴壁工艺新建的1座15 000 m3地下水封油池为例,从技术经济学角度对钢板贴壁油罐作了静态投资分析。该钢板贴壁油罐静态总投资1 756.95万元,其中占总投资比例最高者为地下工程建设,达到53.76%,库容投资1 171.30元/m3。结果表明:钢板贴壁油罐较地下水封石洞油罐整体经济效益明显;投资定额可供编制预算参考。     

开口金属腔体对强电磁脉冲的耦合效应

为了评价腔体开口因素对核电磁脉冲(High-amplitude Electro Magnetic Pulse,HEMP)和高功率微波(High Power Microwave,HPM)破坏效能的影响,采用CST电磁计算软件建立强电磁脉冲的孔缝耦合模型,研究孔缝的位置、大小以及长宽比对HEMP和HPM耦合效应的影响。结果表明,孔缝的位置、大小及长宽比对HEMP的耦合效应影响较大,合理控制孔缝的位置、大小以及长宽比能在一定程度上削弱HEMP的破坏效能。对于HPM,相同条件下其耦合效应要明显强于HEMP。在孔缝达到一定尺寸后,其大小和长宽比对HPM的耦合效应影响较小,仅孔缝位置会带来较大的影响。当开口平面与HPM入射方向平行时,耦合效应最弱,但此时耦合进入腔体内的能量还是很容易达到多种电子元器件的电磁损伤阈值级别。     

Analysis of the stress wave and rarefaction wave produced by hypervelocity impact of sphere onto thin plate

Shock wave is emitted into the plate and sphere when a sphere hypervelocity impacts onto a thin plate. The fragmentation and phase change of the material caused by the propagation and unloading of shock wave could result in the formation of debris cloud eventually. Propagation models are deduced based on one-dimensional shock wave theory and the geometry of sphere, which uses elliptic equations (corresponding to ellipsoid equations in physical space) to describe the propagation of shock wave and the rarefaction wave. The “Effective thickness” is defined as the critical plate thickness that ensures the rarefaction wave overtake the shock wave at the back of the sphere. The “Effective thickness” is directly related to the form of the debris cloud. The relation of the “Effective thickness” and the “Optimum thickness” is also discussed. The impacts of Al spheres onto Al plates are simulated within SPH to verify the propagation models and associated theories. The results show that the wave fronts predicted by the propagation models are closer to the simulation result at higher impact velocity. The curvatures of the wave fronts decrease with the increase of impact velocities. The predicted “Effective thickness” is consistent with the simulation results. The analysis about the shock wave propagation and unloading in this paper can provide a new sight and inspiration for the quantitative study of hypervelocity impact and space debris protection.     

Effect of fusion welding processes on tensile properties of armor grade,high thickness,non-heat treatable aluminium alloy joints

AA5059 is one of the high strength armor grade aluminium alloy that finds its applications in the military vehicles due to the higher resistance against the armor piercing (AP) threats. This study aimed at finding the best suitable process among the fusion welding processes such as gas tungsten arc welding (GTAW) and gas metal arc welding (GMAW) by evaluating the tensile properties of AA5059 aluminium alloy joints. The fracture path was identified by mapping the low hardness distribution profile (LHDP) across the weld cross section under tensile loading. Optical and scanning electron microscopies were used to characterize the microstructural features of the welded joints at various zones. It is evident from the results that GTAW joints showed superior tensile properties compared to GMAW joints and this is primarily owing to the presence of finer grains in the weld metal zone (WMZ) and narrow heat-affected zone (HAZ). The lower heat input associated with the GTAW process effectively reduced the size of the WMZ and HAZ compared to GMAW process. Lower heat input of GTAW process results in faster cooling rate which hinders the grain growth and reduces the evaporation of magnesium in weld metal compared to GMAW joints. The fracture surface of GTAW joint consists of more dimples than GMAW joints which is an indication that the GTAW joint possess improved ductility than GMAW joint.     

Optimization of resistance spot brazing process parameters in AHSS and AISI 304 stainless steel joint using filler metal

The aim of this research study was to determine optimal resistance spot brazing parameters for joining between AHSS and AISI 304 stainless steel by using filler metal. The key parameters investigated in this study consist of the brazing current, electrode pressure and brazing time. The Taguchi method was applied to the design of experiments. Signal-to-Noise ratio was introduced in the study to identify optimal levels from the process where input parameters yield increased shear strength. Brazing was thus implemented with 5,000A brazing current, 0.70 MPa electrode pressure, and 1.50s brazing time. The maximum shear strength obtained was 54.31 N·mm⁻² in accordance with input parameter settings. In addition, Cu-rich phase and Ag_0.4Fe_0.6 intermetallic phases were found at the interface zone.     

适用于金属物体识别的L形无芯RFID标签设计

设计了一种L形无芯射频识别标签,该标签包含6个不同尺寸的L形散射单元,利用其交叉极化方向上的反向散射场进行识别。标签基于频域特征进行编码,每个标签可携带6 bit信息。使用CST仿真软件对所设计L形无芯RFID标签进行仿真,分析了L形散射单元的尺寸变化时对标签谐振特性的影响。此外,还仿真了标签的接地板尺寸增加后的情况,证明该标签可适用于金属物体的识别或金属背景下的物体识别。     

Kelvin模型阻尼层合板的振动分析

基于Kelvin模型粘弹性材料本构关系导出了阻尼层合板的动力学微分方程组,给出了四边简支阻尼层合板的固有频率和损耗因子的解析解。与文献结果比较表明,将Kelvin模型应用于粘弹结构的动力特性问题求解,计算模型简便,且计算结果比常复数模型更为精确。分析了阻尼层参数变化对结构振动特性的影响。分析结果表明:增加阻尼层厚度,可以有效提高结构损耗因子;增加阻尼层材料的剪切模量,结构损耗因子增大到一定值后又逐渐减小,在减振设计中阻尼层的模量存在最佳值。