形状记忆合金自复位减振装置研制与验证

为改善第二喉道中的可调中心体机构(简称中心体)在工作状态下的流致振动,根据形状记忆合金(shape memory alloy, SMA)偏置双程驱动原理,设计制作一种能够满足中心体有限安装空间要求的SMA自复位减振装置;采用UMAT接口编制的SMA本构关系子程序实现减振装置最大压紧力的数值分析,数值分析与静态调试试验结果误差约为2.58%;搭建地面减振试验平台,测试SMA自复位减振装置分离和闭合状态下的中心体零部件振动响应。减振试验结果显示:SMA自复位减振装置闭合后,中心体振动响应明显降低,在0～100 Hz频带内,均有明显的减振效果,低频至55 Hz范围内,减振率均大于50%。     

电子在材料中输运的蒙特卡罗模拟

介绍了电子输运问题的蒙特卡罗方法的基本原理和步骤。电子输运过程的模拟采用了“浓缩历史”蒙特卡罗方法 ,电子随机游动步长根据能量步划分 ,在每个电子游动步内 ,电子的能量损失为非辐射 (碰撞 )能量损失和辐射 (韧致辐射 )能量损失之和 ,其中非辐射能量损失通过对Landau公式的随机抽样得到 ,辐射能量损失以及韧致辐射光子的产生通过利用Bethe Heitler的随机抽样处理 ,在每个电子游动步结束时电子的出射角的抽样利用Gouddsmit Saunderson多重散射公式 ,电子 -电子的散射利用Moller截面公式进行抽样。最后对电子在航天用合金铝平板材料中的输运进行了模拟计算并给出了计算结果     

化学敏感材料的应用与发展

对敏感材料的特点、分类及其在科技、化工等领域内的广泛应用和发展前景 ,进行了较全面的综述     

High strain rate deformation of explosion-welded Ti6Al4V/pure titanium

Multilayer materials are widely used in military, automobile and aerospace industries. In this paper, the response of an explosion-welded Ti6Al4V/pure titanium with a flat interface to dynamic loading is investigated. An SHPB apparatus is used. Then, the dynamic behaviour of a bimetal sample is explored with a DIC system coupled to the SHPB. Result indicates that in the bimetal sample pure titanium is deformed and failed before Ti6Al4V. The stress curve of the sample shows two different peaks in a striker velocity higher than the 18.3 m/s. When the incident wave encounters the interface of the Ti6Al4V/pure titanium sample, only a small fraction of the wave is reflected owing to similar impedance. Using the direct interpretation stress-strain curve is unreasonable in this case because of unhomogenised plastic deformation. The microstructure of the sample is investigated after loading. An adiabatic shear band is formed in the pure titanium side before failure, and the interface of the sample remains intact under different loading conditions. The FEM simulation result for the sample is in good agreement with experimental observations.     

Texture evaluation in AZ31/AZ31 multilayer and AZ31/AA5068 laminar composite during accumulative roll bonding

This article presents the texture development of magnesium AZ31 alloy in the accumulative roll bonded (ARB) AZ31/AZ31 multilayer and AZ31/AA5086 laminate composite. The comparative study demonstrates that the texture evolution in AZ31 in a multilayer system is strongly influenced by the interfaces. A typical basal texture of AZ31 has been observed in AZ31/AZ31 multilayer with texture intensity increased with the rolling deformation. Presence of AZ31/AA5086 interface in the laminate composite leads to a tilted basal texture along the rolling direction (RD) in AZ31 alloy. The texture intensity of composite increased initially with rolling reduction and weakened at the higher rolling strain. Weakening of texture in AZ31 during the laminate processing at higher strain has been attributed to the development of wavy interfaces in AZ31/AA5086 laminate.     

H2O2对镁合金稀土转化膜性能的影响

选择AZ91D镁合金为实验材料,利用扫描电镜和能谱分析、Tafel曲线和阻抗谱等分析手段,研究了H2O2的添加量对铈转化膜的微观形貌以及耐蚀性能的影响。结果表明：随H2O2添加量的增多,转化膜表面状态越不均匀,自腐蚀电位降低,转化膜电阻Rf变小,较为合适的H2O2添加量为5 mL/L。     

铝合金-纯铝-钢复合板爆炸焊接试验及性能研究

通过设计爆炸焊接试验复合了铝合金-纯铝-钢爆炸复合板,对其界面形态、显微硬度及力学性能进行了研究。结果表明,铝合金-纯铝界面纯规则正弦波形,纯铝-钢复合板界面波形较小,铝合金-纯铝-钢复合板的界面剪切强度在75 MPa以上,爆炸复合过程中,纯铝与钢界面生成了金属间化合物,其界面处基体金属发生强烈的塑性变形。复合板变形及组织变化的结果造成复合板界面处的显微硬度最高,随着距界面距离的增加,两侧基体金属的硬度逐渐降低。     

关于S147 铝合金形变时效强化研究

本文研究了S147铝合金板材在形变时效处理各工艺阶段中的组织与性能。用扫描电镜观察分析了材料的断口形貌,并用薄膜试样在透射电镜下分析研究了该合金形变时效处理后的微观亚结构及过渡相析出物特征。结果表明,最佳形变时效处理可显著提高S147铝合金的强度及塑韧性,并能改善其过渡相析出过程及特征。     

Zn-Pb合金液相分离机制研究

根据Zn-Pb合金液相分离过程,建立了两相熔体中弥散相液滴粗化模型,并进行了模拟计算。通过试验对比,证实了该模型的理论合理性。     

稀土离子La~(3+)、Ce~(3+)对铝合金孔蚀的缓蚀作用实验分析

用电化学方法研究了稀土离子La~(3+)、Ce~(3+)对铝合金LY12CZ在中性含Cl~-离子水溶液中对孔蚀行为的缓蚀作用,测定了孔蚀电位E_b,保护电位E_p以及诱导时间等,结果表明,两种离子对铝合金LY12CZ的孔蚀均有较好的缓蚀作用。并进行了机理分析。