影响亚微米级HMX粉碎效果的因素分析

介绍了高速撞击流技术制备亚微米级超细HMX的工艺流程,通过实验分析了加载压力、循环处理次数、表面处理剂对HMX颗粒粉碎效果的影响,得出了此法的最佳工艺条件:加载压力1500MPa,循环处理次数5次,悬浮液浓度5％,去离子水配液并加入表面处理剂A。     

驱动管中柱状装药爆轰过程的数值模拟

数值模拟了爆炸驱动管中柱状装药内爆轰波的传播过程.计算采用欧拉型有限体积方法,炸药及爆轰产物均采用JWL状态方程,空气采用理想气体状态方程,采用"点火-生长"模型计算化学反应速率.计算得到了驱动管内波系结构的发展过程,爆速与经验公式符合得较好.计算表明,驱动管侧壁的压力峰值在800MPa以上,而在管底中心处,由于激波的汇聚,压力峰值高达12.4GPa.     

灭火弹比药量与灭火效果关系研究

在相同的试验条件下,对采用鼠笼式结构的灭火弹进行了静爆试验,并对采用不同比药量的灭火剂在爆轰作用下抛撒云团的成长过程和灭火效果进行对比分析,得出比药量与灭火效果的关系,最后确定最佳比药量。     

The investigation of NTO/HMX-based plastic-bonded explosives and its safety performance

3-nitro-1,2,4-triazol-5-one (NTO) is the main component of insensitive munitions (IM) formulation because of its outstanding insensitive properties.In this paper,a series of NTO/HMX-based composite explosives were prepared and characterized.The study focuses on the effect of NTO on the performance of the formulations,especially the safety performance.The results revealed that the mechanical sensi-tivity of formulations was associated with NTO content,as well as the thermal conductivity,specific heat capacity and Arrhenius parameters.Then,the high amount of NTO using in formulation was proved to be helpful for NTO/HMX-based formulation to exhibit good thermal safety.Besides,by accelerating rate calorimeter (ARC) and a modified cook-offequipment,the pressure and pressure rise rate were proved as the important indicator for judging the thermal safety performance in confined spaces.Finally,the numerical simulation was used as a credible method for predicting the respond temperature of cook-off experiment.     

超细粒子对环氧树脂的增韧改性研究

用NW-2辛酯偶联剂改性过的复合氧化锌(ZnO)超细粒子对环氧树脂进行增韧,借助于SEM和力学性能测试手段研究了ZnO粒子的形貌以及NW-2辛酯偶联剂改性复合ZnO粒子在环氧树脂体系中的增韧情况及其机理.结果表明:经过NW-2辛酯偶联剂改性的复合超细ZnO粒子对环氧树脂具备良好的增韧效果.     

电磁辐射对桥丝式电火工品性能影响研究

利用传导方法研究射频对桥丝式电火工品的桥丝电阻、烤爆、迟发火以及瞎火等性能影响。研究结果表明,在10％发火功率和0．4MHz的敏感频率条件下,所研究的3种电火工品在照射1～5min后,电阻增加1.2％～7．4％,并且17．3％的试样在照射的过程中出现了烤爆;在对经过照射后的试样进行正常的发火感度试验中,发火时间显著增加,出现了不同程度的迟发火,16．9％的试样瞎火。     

Numerical investigation of the shockwave overpressure fields of multi-sources FAE explosions

Shockwaves from fuel-air explosive (FAE) cloud explosions may cause significant casualties. The ground overpressure field is usually used to evaluate the damage range of explosion shockwaves. In this paper, a finite element model of multi-sources FAE explosion is established to simulate the process of multiple shockwaves propagation and interaction. The model is verified with the experimental data of a fourfold-source FAE explosion, with the total fuel mass of 340 kg. Simulation results show that the overpressure fields of multi-sources FAE explosions are different from that of the single-source. In the case of multi-sources, the overpressure fields are influenced significantly by source scattering distance and source number. Subsequently, damage ranges of overpressure under three different levels are calculated. Within a suitable source scattering distance, the damage range of multi-sources situation is greater than that of the single-source, under the same amount of total fuel mass. This research provides a basis for personnel shockwave protection from multi-sources FAE explosion.     

Increasing of photostability of HNS explosive in the presence of UV photostabilizers

The photostabilies of hexanitrostillbene(HNS)were studied at 1％wt.of photostabilizers.The photo-stabilizers of Chiguard BP-12(UV-531),ADK STAB LA-326(UV-326),ADK STAB LA-32(UV-P),Irganox 1010 and Everstab LS944 were used in this study.A photoreactor including a 30 W monochromatic UV lamp was used for investigation of photodegradations of solid HNS.The changes in surface area of HNS peak in HPLC chromatogram at time intervals of 2,4,6 and 8 h were used for calculation of kinetic rate constants of photodegradation process.The compound of UV-P photostabilizer was found to have the greatest effect on enhancing photostability for HNS among the investigated photostabilizers.The kinetic rate constants were obtained 6.2 × 10-2 and 4.1 × 10-2 h-1,respectively,for photodegradation process of HNS in absence and in presence of UV-P.     

Effect of metal powders on explosion of fuel-air explosives with delayed secondary igniters

In order to improve the energy level of fuel air explosive(FAE) with delayed secondary igniters, high energetic metal powders were added to liquid fuels mainly composed of ether and isopropyl nitrate. Metal powders' explosive properties and reaction mechanisms in FAE were studied by high-speed video, pressure test system, and infrared thermal imager. The results show that compared with pure liquid fuels, the shock wave overpressure, maximum surface fireball temperature and high temperature duration of the mixture were significantly increased after adding high energetic metal powder. The overpressure values of the liquid-solid mixture at all measuring points were higher than that of the pure liquid fuels. And the maximum temperature of the fireball was up to 1700 ℃, which was higher than that of the pure liquid fuels. After replacing 30％of aluminum powder with boron or magnesium hydride, the shock wave pressure of the mixture was further increased. The high heat of combustion of boron and the hydrogen released by magnesium hydride could effectively increase the blast effect of the mixture. The improvement of the explosion performance of boron was better than magnesium hydride. It shows that adding high energetic metal powder to liquid fuels can effectively improve the explosion performance of FAE.     

A novel method for determination of lethal radius for high-explosive artillery projectiles

A new model has been defined that enables the estimation of the lethal radius (radius of efficiency) of HE (High Explosive) artillery projectiles against human targets. The model is made of several modules: CAD (Computer Aided Design) modeling, fragment mass distribution estimation, fragment initial velocity prediction, fragment trajectory calculation, effective fragment density estimation, and high explosive projectile lethal radius estimation. The results were compared with the experimental results obtained based on tests in the arena used in our country, and the agreement of the results was good. This model can be used in any terminal-ballistics scenario for high explosive projectiles since it is general, para-metric, fast and relatively easy to implement.