飞机运动特征对动态RCS序列的影响分析

针对超音速隐身飞机难以探测的问题,仿真分析了F-22飞机在不同运动特征下的动态RCS,并对其频率响应和极化响应特性做进一步的研究。首先设定飞行航迹,并考虑实际中随机抖动的影响,获取时变的雷达视线姿态角;其次应用物理光学并结合等效电磁流的方法,计算分析了飞机以不同的速度沿不同航迹飞行时的动态RCS。对于使飞机动态RCS变化最明显的运动特征,仿真计算了其在不同频段、不同极化下的动态RCS。仿真结果表明:在不同航迹下,飞机速度对其动态RCS的影响程度不同,且当飞机沿小航路捷径低速或者高速飞行时,其RCS值减小最为明显,利用极化响应和频率响应特性可以有效地削弱这一影响。研究成果对于超音速隐身飞机目标的预警探测具有重要意义。     

含运动副间隙舵机执行机构的动态特性研究

为了研究运动副间隙对空间4R机构动态特性的影响,间隙处的接触碰撞模型和摩擦的建立分别采用非线性弹簧阻尼模型和修正的库伦摩擦模型。在Solidworks中建立空间4R机构模型,导入ADAMS中进行动力学仿真分析。对比含间隙和不含间隙时系统动力学仿真结果的异同,分析间隙大小和最佳间隙量对空间4R机构动态特性的影响,为机构的设计提供了重要的参考依据,有利于工程实际应用。     

飞行器动态滑翔的受力平衡状态

为了研究动态滑翔的物理本质,从受力平衡的角度出发,根据物理定律推导平衡方程,从数学上求解出方程解集构成的平衡曲线。以信天翁和某小型无人机在不同风梯度下滑翔为例对平衡曲线进行仿真。分析和仿真结果表明:平衡曲线是满足受力平衡的所有速度状态的集合,由上升和下降两个分支构成;上升分支只有当风梯度足够大时才存在,是动态滑翔的关键。     

Simulation on the dynamic stability derivatives of battle-structure-damaged aircrafts

Accurately evaluating the aerodynamic performance of a battle-structure-damaged aircraft is essential to enable the pilot to optimize the flight control strategy. Based on CFD and rigid dynamic mesh techniques, a numerical method is developed to calculate the longitudinal and longitudinal-lateral coupling forces and moments with small amplitude sinusoidal pitch oscillation, and the corresponding dynamic de-rivatives of two fragment-structure-damaged and two continuous-rod-damaged models modified from the SACCON UAV. The results indicate that, at the reference point set in this paper, additional positive damping is generated in fragment-damaged configurations; thus, the absolute values of the negative pitch dynamic derivative increase. The missing wingtip induces negative pitch damping on the aircraft and decreases the value of the pitch dynamic derivative. The missing middle wing causes a noticeable increase in the absolute value of the pitch dynamic derivative;the missing parts on the right wing cause the aircraft to roll to the right side in the dynamic process, and the pitch-roll coupling cross dynamic derivatives are positive. Moreover, the values of these derivatives increase as the damaged area on the right wing increases, and an optimal case with the smallest cross dynamic derivative can be found to help improve the survivability of damaged aircraft.     

在柴油机放热曲线计算中两个关键问题的解决方法

对影响柴油机放热曲线精度计算的因素进行了讨论 ,并对影响放热率计算的主要问题如动态上止点修正、示功图光顺处理两个主要环节进行了分析研究 ,提出了解决方法 .     

基于分形几何的信号特征提取技术及其应用研究

针对分形客观展现事物原貌的特点 ,从工程应用的角度分别对信号的分形性验证、有效分析区间的确定、分形性描述和刻画、设备状态的趋势分析等方面作了探讨 ,形成了基于分形几何的信号特征提取技术 ,并描绘出基于分形几何的设备故障诊断模式     

血小板在凝血中作用的动力学模型

在生化实验的基础上提出了血小板在凝血中作用的动力学模型,通过定性分析和数值模拟,得到了血小板的激活比率、因子Ⅷ、Ⅸ对凝血酶生成有重要影响的一系列结论.     

A comparative study of three tool replacement/operation sequencing strategies in a flexible manufacturing system

This paper studies three tool replacement/operation sequencing strategies for a flexible manufacturing system over a finite time horizon: (1) failure replacement—replace the tool only upon failure, (2) optimal preventive tool replacement for a fixed sequence of operations, and (3) joint scheduling of the optimal preventive tool replacement times and the optimal sequence of operations. Stochastic dynamic decision models are used for strategies 2 and 3. The optimization criterion for strategies 2 and 3 is the minimization of the total expected cost over the finite time horizon. We will show through numerical studies that, with the same amount of information, the total expected costs can be reduced considerably by choosing an optimal strategy. Our conclusion is that in flexible manufacturing, optimal tool replacement and optimal operations sequencing are not separate issues. They should be considered jointly to minimize the expected total cost. © 2000 John Wiley & Sons, Inc. Naval Research Logistics 47: 479–499, 2000     

非对称通气空泡多相流场特性研究

通气空泡的非对称介质分布将影响其水动力特性,继而影响空泡稳定控制,目前对其流动特性的认识较为局限。为揭示非对称通气空泡的流动机理,基于循环水洞实验及数值仿真开展了多相流场特性研究。结果表明：非对称流动导致空泡形成非对称沾湿区,依据流动介质的不同,非对称沾湿区可分为透明气相区、水气混合区及沾湿区。水气混合边界由底端母线向顶端母线发展过程中,滞止高压减小,空泡厚度增加,液体进入空泡内部方式从主要由轴向进入转化为主要由周向进入,同时水气混合物在来流作用下逐渐聚集,水气混合区面积随之增大。随着空泡闭合点逐渐靠近顶端母线,沿周向流动的液体层发展至顶端母线,顶端母线处则形成低速、高压、水气掺混区,湍流特性增强,并伴有大量细碎空泡涡的脱落。     

基于XML的装备维修信息标准化

基于XML的装备维修信息标准化是我军装备信息保障的发展趋势.以设备技术说明书为例,对其进行了标准化信息分解,构建了相应的DTD和数据库结构,并讨论了实现标准化维修信息动态传输与交换的相关问题.