黏弹性基体中挠曲电Timoshenko纳米梁振动特性分析

以黏弹性基体中的Timoshenko纳米梁为研究对象,综合考虑非局部效应、压电效应和挠曲电效应的影响,基于哈密顿原理建立了系统的振动控制方程和相应的边界条件,给出了两端简支边界条件下挠曲电纳米梁控制方程的求解方法,系统地研究了非局部参数、挠曲电系数以及黏弹性基体对挠曲电纳米梁振动特性的影响规律。结果表明:横向挠曲电系数能显著增加挠曲电纳米梁的结构刚度,而非局部效应和切向挠曲电系数则会降低系统的结构刚度。此外,通过研究黏弹性基体的影响规律,可得到挠曲电纳米梁不再发生往复振动时对应的黏弹性基体临界阻尼系数。相关研究结果可为挠曲电纳米梁在俘能器中的推广应用提供理论基础。     

Noise and vibration measurements in a Viking military vehicle

Noise and whole-body vibration measurements were made in a Viking military vehicle to determine the variation that should be expected during repeat measures, the effect of speed (up to 60 km/h in 5 km/h increments), and during travel over different types of terrain (comprising concrete road, gravel track and rough cross-country). Measurements were made at various crew positions (including the driver and commander) in both the front and the rear cabs in the vehicles. Three translational axes of vibration were measured in each seat. Two speeds were investigated over road (35 km/h and 55–60 km/h) and gravel (20 km/h and 35 km/h) surfaces. The effect of varying speed of the vehicle on the measured noise and vibration magnitudes was also investigated. The highest sound pressure level (L_Aeq) of 104 dB(A) was measured at the commander’s standing position during travel over concrete road at 55 km/h. Higher noise levels occurred for a standing commander compared with when sitting on the seat. A maximum single axis frequency-weighted vibration magnitude of 1.0 m/s² r.m.s. was measured on the driver’s seat during travel over track at 35 km/h. Higher vibration magnitudes occurred during travel over track compared with travel over road. Both noise and vibration exposure of crew within the Viking vehicle increased with increasing speed of the vehicle.     

Static and free vibration analyses of functionally graded porous variable-thickness plates using an edge-based smoothed finite element method

The main purpose of this paper is to present numerical results of static bending and free vibration of functionally graded porous (FGP) variable-thickness plates by using an edge-based smoothed finite element method (ES-FEM) associate with the mixed interpolation of tensorial components technique for the three-node triangular element (MITC3), so-called ES-MITC3. This ES-MITC3 element is performed to eliminate the shear locking problem and to enhance the accuracy of the existing MITC3 element. In the ES-MITC3 element, the stiffness matrices are obtained by using the strain smoothing technique over the smoothing domains formed by two adjacent MITC3 triangular elements sharing an edge. Materials of the plate are FGP with a power-law index (k) and maximum porosity distributions (Ω) in the forms of cosine functions. The influences of some geometric parameters, material properties on static bending, and natural frequency of the FGP variable-thickness plates are examined in detail.     

Effect of projectile parameters on opening behavior of PELE penetrating RC target

When a penetrator with enhanced lateral effect (PELE) impacts on a reinforced concrete (RC) target, the target is damaged with a large opening. An understanding of how PELE projectile parameters affect the opening dimension, is essential for effective design of the PELE projectile. In this study, under the condition that the impact velocity and target parameters (strength and thickness) were fixed values, the important influence factors of the PELE (jacket wall thickness B, jacket material strength Y1, filling material strength Y2 and angle of monolithic jacketθ) were determined by a dimensional analysis. Tests and simulations of the PELE penetrating the RC target were conducted to analyze the influence of these factors on opening diameter ((D), an equivalent diameter under relative kinetic energy). Based on the test and simulation results, it is found that the influence of these factors B, Y1 andθon the deformation mode of the jacket shows a similar trend:as values of the three factors decrease, the jacket deforms from small bending deformation to large one, and then to curling deformation. This causes the opening diameter to first increase with the decrease of these three factors, and then decreases. It is well known that the bending resistance of the jacket is related to these factors B, Y1 andθ. Therefore, a plastic limit bending moment (M0) of the jacket was quoted to characterize the influence of these factors on the bending deformation of the jacket and the opening diameter of the target. The influence factor Y2 causes (D) to first increase with the increase of Y2, and then decreases. A formula was developed to predict the opening diameter, whose influence parameters were considered in a dimensionless way. It has been shown that the dimensionless opening diameter (D)/d1 is dependent on two dimensionless parameters Q = (d31fc/M0) and G = (fc/Y2), where d1 and fc are the outer diameter of the projectile and the compressive strength of the target, respectively.     

Quasi-steady aerodynamic characteristics of Terminal Sensitive Bullets with short cylindrical portion

The aerodynamic characteristics are vital for short cylindrical Terminal Sensitive Bullets(TSB)with low aspect ratio,especially in terminal trajectory.Currently,there is little research in terms of the TSB and short cylinder with two free ends,and particularly in this trajectory,where the scanning angle β and roll angle α vary over a broad range between 0° and 180°.In this work,wind tunnel experiments are first conducted to learn the effects of Reynolds number and scanning angle on aerodynamic parameters for short cylinder with aspect ratio L/D = 1.Similar to infinite cylinder,for the short cylinder with two free ends,the drag crisis phenomenon still exists in the critical regime 1.7 × 105 ≤ Re ≤ 6.8 × 105.Then 3D simulations are performed to demonstrate the aerodynamic characteristics of short cylinder and TSB over a broad range of Re,L/D,α and β.The sensitivity analysis of time step and grid are presented as well.When β=0°,for short cylinder,the drag crisis phenomenon was also observed in the simulation,but not as obvious as in the wind tunnel test.In some attitudes,there is an obvious Kármán vortex in the wake of short cylinder and TSB.The correlation between time-averaged aerodynamic coefficients and L/D,Re,α&β is discussed.The vortex shedding frequency and shear layer behavior are obtained for quasi-steady and unsteady flow.Finally,the effect of end's shape on drag reduction and vortex shedding frequency is analyzed.     

水下声探测系统载体振动干扰分析及抑制方法

针对水下探测系统载体振动对目标回波信号的微多普勒特征谱产生干扰的问题,从干扰产生的基本原理出发,推导了干扰的近似乘性表达式。在获取振动干扰数据的条件下,提出了针对乘性干扰的干扰抑制算法,并针对推导干扰乘性表达式时的近似条件,分析了近似算法带来的误差。仿真结果表明,该方法可有效抑制水下探测系统平台振动对目标回波信号的微多普勒特征谱产生的干扰,并且在绝大多数情况下,由算法带来的误差可以忽略不计。     

舰船管路橡胶减振器的应用

简要分析了管路橡胶减振器对刚性管路的隔振原理,提出了几种通过改变管路布置形式而达到对管路各自由度上减振的方法,阐述了在实际应用中如何调整橡胶隔振器的固有频率而达到对舰船管路良好的隔振.     

外光电效应中光电流的计算

根据金属中电子系统可假设为具有质量为m的粒子组成的理想费密气体,其在热平衡时服从费密-狄喇克分布规律,导出单位强度单色光束照射金属时所感生的光电流.     

水橇在地效翼船上的应用前景及设计思想

参阅了大量国外有关水橇的理论和试验资料,明确了水橇在地效翼船上缓冲冲击的作用,系统地分析了水橇各种设计参数,定性地指出了水橇设计的最佳形状以及实用中应注意的问题.