关联维数在梁式结构损伤检测中的应用

为探索有效实用的结构损伤检测方法,运用分形理论直接对结构振动信号进行关联维数分析,通过度量系统输出的奇异性来识别结构的局部损伤,提出了基于振动响应关联维数的结构损伤检测方法.简支梁损伤算例结果表明,该方法能够准确地检测出梁式结构单个和多个不同程度的损伤位置,同时关联维数指标变化值会随着损伤程度的增加而增大.与曲率模态指...     

基于MOEA/D的航天器隔振器多目标优化方法研究

由于存在各种高频内部扰动,高精度航天器通常需要进行隔振设计,而被动隔振装置被广泛采用。在被动隔振装置设计中,抑制共振响应峰和隔离中高频振动存在很强的冲突性,需要进行多目标优化设计。首先,建立了隔振系统的动力学模型,提出了以传递函数共振峰幅值和中高频衰减为目标函数的多目标优化模型;其次,提出了基于分解的多目标进化算法（MOEA/D）对单级和两级级隔振装置进行多目标优化的设计方法;最后,对某空间隔振装置进行了数值仿真,结果验证了本文算法的有效性。     

Noise and vibration measurements in a Viking military vehicle

Noise and whole-body vibration measurements were made in a Viking military vehicle to determine the variation that should be expected during repeat measures, the effect of speed (up to 60 km/h in 5 km/h increments), and during travel over different types of terrain (comprising concrete road, gravel track and rough cross-country). Measurements were made at various crew positions (including the driver and commander) in both the front and the rear cabs in the vehicles. Three translational axes of vibration were measured in each seat. Two speeds were investigated over road (35 km/h and 55–60 km/h) and gravel (20 km/h and 35 km/h) surfaces. The effect of varying speed of the vehicle on the measured noise and vibration magnitudes was also investigated. The highest sound pressure level (L_Aeq) of 104 dB(A) was measured at the commander’s standing position during travel over concrete road at 55 km/h. Higher noise levels occurred for a standing commander compared with when sitting on the seat. A maximum single axis frequency-weighted vibration magnitude of 1.0 m/s² r.m.s. was measured on the driver’s seat during travel over track at 35 km/h. Higher vibration magnitudes occurred during travel over track compared with travel over road. Both noise and vibration exposure of crew within the Viking vehicle increased with increasing speed of the vehicle.     

Quasi-steady aerodynamic characteristics of Terminal Sensitive Bullets with short cylindrical portion

The aerodynamic characteristics are vital for short cylindrical Terminal Sensitive Bullets(TSB)with low aspect ratio,especially in terminal trajectory.Currently,there is little research in terms of the TSB and short cylinder with two free ends,and particularly in this trajectory,where the scanning angle β and roll angle α vary over a broad range between 0° and 180°.In this work,wind tunnel experiments are first conducted to learn the effects of Reynolds number and scanning angle on aerodynamic parameters for short cylinder with aspect ratio L/D = 1.Similar to infinite cylinder,for the short cylinder with two free ends,the drag crisis phenomenon still exists in the critical regime 1.7 × 105 ≤ Re ≤ 6.8 × 105.Then 3D simulations are performed to demonstrate the aerodynamic characteristics of short cylinder and TSB over a broad range of Re,L/D,α and β.The sensitivity analysis of time step and grid are presented as well.When β=0°,for short cylinder,the drag crisis phenomenon was also observed in the simulation,but not as obvious as in the wind tunnel test.In some attitudes,there is an obvious Kármán vortex in the wake of short cylinder and TSB.The correlation between time-averaged aerodynamic coefficients and L/D,Re,α&β is discussed.The vortex shedding frequency and shear layer behavior are obtained for quasi-steady and unsteady flow.Finally,the effect of end's shape on drag reduction and vortex shedding frequency is analyzed.     

稀土永磁减振器特性的数值模拟分析

简要介绍了目前稀土永磁减振器的研究现状和单质量稀土永磁减振器的结构与工作原理,运用大型有限元软件ANSYS对稀土永磁减振器的工作过程进行数值模拟,分析其在工作过程中的磁通密度、磁力线分布、力学特性以及它们之间的相互关系。研究表明:稀土永磁减振器具有较好的非线性减振效果;ANSYS在模拟稀土永磁减振器工作过程时,能形象直观的反映其在工作过程中的各种特性参数。     

一种金属橡胶元件建模方法研究

用理论和试验相结合的手段研究金属橡胶弹性元件的动力学建模,提出一种新的建模方法,用此方法建立了基于迟滞回线拟和分解的高次弹性复合阻尼模型。该模型用非线性刚度和非线性复合阻尼机理构造,模型中的参数由试验数据辨识。用所建模型重构恢复力-位移迟滞回线,结果表明该模型能很好描述这类非线性振动系统的特性。     

弹/枪相互作用引起的运动步枪枪口振动分析

为研究身管结构参数变化对运动步枪枪口振动的影响规律,采用非线性有限元方法建立了运动步枪弹/枪相互作用数值计算模型。借助压力测试系统对运动步枪进行了膛压测试试验;使用高速摄影设备实测了枪口在发射过程中竖直方向的振动规律,通过对比枪口实测数据与数值计算结果验证了模型的正确性。数值模型为研究参数变化对枪口振动的影响提供了理论基础,研究结果对工程实践具有一定实际意义。     

燃气射流引起的火箭发射系统振动特性分析

以火箭发射系统为研究对象,对其56°射角工况下发射过程中的振动特性进行分析。创新点在于确定发射过程中动态载荷的加载方法,即首先根据发射系统有限元分析结果确定迎气面上试验测量点的具体位置,然后测得燃气射流冲击压强随时间变化的数值,并对试验测得数据进行处理,最后推导冲击压力对于径向距离的直线公式。所采用的冲击压强分析方法为研究其他武器系统受燃气射流冲击的影响提供了重要的指导意义。     

基础阻抗对隔振效果的影响

经典隔振理论评价隔振效果常假定基础为绝对刚性,这在隔振效果评价和测量上带来了很大的问题,导致计算结果偏差很大.针对这一问题推导了柔性基础上的传递率计算公式,讨论了基础阻抗对隔振效果的影响.理论分析表明,柔性基础的基频和质量是影响隔振效果的最重要因素.     

非线性系统参数识别的傅里叶级数展开法

采用电液伺服材料试验机加载方式,通过位移控制和傅里叶级数展开技巧,将含有滞迟环节系统的非线性参数识别问题转化为扩充参数的线性识别问题,为钢丝绳、金属橡胶构成的隔振系统的模型识别奠定了重要的理论基础。