含诱导缺陷复合材料T型接头的弯曲失效实验

通过实验研究含不同诱导缺陷的复合材料T型接头的弯曲力学性能和失效过程,采用引入脱黏缺陷和三角区填充率缺陷来诱导T型接头的不同失效模式。结果表明不同失效模式下T型接头所表现出来的弯曲力学性能差异极大,完好的T型接头所能承受的载荷为288.5N,界面脱黏会削弱其30%的承载能力,而三角区填充率的减少会导致裂纹在填充区内部引发和扩展,导致T型接头的弯曲力学性能大幅降低。     

Effect of bending temperatures on the microstructure and springback of a TRIP steel sheet

Transformation-induced plasticity (TRIP) steel possesses high strength and formability, enabling the use of a thinner gauge material and allowing for the fabrication of complex shapes. In this research, we measured the effect of bending temperatures on the microstructure and air-bending springback angle of TRIP steel at temperatures from 25 to 600 °C. Real-time in situ X-ray diffraction and scanning electron microscopy were used for pre- and postbending analysis. As the prebending temperature increased from 25 °C to 600 °C, the retained austenite (RA) volume fraction decreased, and the RA transformed to bainite at temperatures above 400 °C. The springback angle was positively correlated with the prebending RA volume fraction, with the smallest springback angle achieved at 400 °C. Additionally, the springback angle was positively correlated with the bending angle, because the RA transformation ratio contributed to increased strain hardening. Further microstructure analysis revealed that the RA became elongated in the tension direction as the bending temperatures increased.     

Strain concentration caused by the closed end contributes to cartridge case failure at the bottom

Ruptures at the bottom of cartridges are a common cause of failure of ammunitions, which directly threatens the safety of weapons and shooters. Based on plastic tube theory, this study analyses the radial and axial deformation of a cartridge, considering the radial constraint of the closed end at the bottom of the cartridge. Owing to the influence of the closed end, the bottom of a cartridge does not establish complete contact with the chamber. Owing to strain concentration in the non-contact area, this area is more amenable to the occurrence of cartridge rupture. This theory predicts the location of the fracture more accurately than the traditional theory. The maximum axial deformation of a cartridge comprises bending and friction deformation. The maximum strain at the bottom of the cartridge increased by 135% owing to the introduction of bending strain caused by the closed end. The strain distribution of a cartridge was measured using digital image correlation technology, and the measured result was consistent with the predicted results of the bending deformation theory and rupture case. The effects of wall thickness, radial clearance, friction coefficient, and axial clearance on the axial deformation of the cylinder were studied. Increasing the wall thickness and reducing radial clearance were found to reduce bending deformation; furthermore, lubrication and reduction in axial clearance reduce frictional deformation, which in turn reduce cartridge rupture.     

梁在拉伸力和弯曲力矩联合作用下的动态塑性断裂

本文采用刚塑性分析方法,研究了韧性材料带裂纹有限长梁在轴向拉伸力和弯曲力矩联合作用下的全塑性断裂过程,其外加轴向拉伸力和弯曲力矩为准静态加载,并在梁的断裂过程中保持不变,为定常载荷。在外力作用下,梁的断裂截面首先进入塑性变形,当裂纹尖端张开位移 CTOD 达到其材料临界值时,裂纹将启裂扩展。本文考虑了应变率对断裂过程的影响,给出了梁在断裂过程中其裂纹扩展长度,裂纹扩展速度以及断裂截面上的轴向抗力和弯曲抗力随时间的变化规律,并比较了在不同轴向拉伸力作用下梁的动态塑性断裂过程的变化,说明了轴向作用力对梁的断裂过程的影响。