Effect of nano powder (Al2O3-CaO) addition on the mechanical properties of the polymer blend matrix composite

This work describes the preparation and study of the properties of composite nanoparticles prepared by the sol-gel method which consists of two materials (Al₂O₃-CaO), and study the effect of these nanoparticles on the mechanical behavior of a polymer blend (EP 4% + 96% UPE). The powder was evaluated by X-ray diffraction analysis, scanning electron microscopy analysis (SEM), particle size analysis, and energy dispersive X-ray analysis (EDX). The mechanical behavior of the composite material was assessed by tensile test, bending test and hardness test. The evaluation results of the composite nanoparticles showed good distribution of the chemical composition between aluminum oxide and calcium oxide, smoothness in particles' size at calcination in high and low temperatures, formation of different shapes of nanoparticles and different (kappa and gamma) phases of the Al₂O₃ particles. The results of mechanical behavior tests showed marked improvement in the mechanical properties of the resulted composite material, especially at 1.5%, compared with polymer blend material without nano powder addition. The tensile properties improved about (24 and 14.9) % and bending resistance about (23.5 and 16.8) % and hardness by (25 and 22) % when adding particles of size (63.8 and 68.6) respectively. Therefore, this reflects the efficiency of the proposed method to manufacture the nanocomposite powder and the possibility of using this powder as a strengthening material for the composite materials and using these composite materials in bio applications, especially in the fabrication of artificial limbs.     

高pH条件纳米Fe_3O_4催化H_2O_2分解去除水中4-氯酚

为了克服非均相fenton催化反应中溶液初始pH过低的缺点,开展了pH=5时Fe3O4/H2O2体系催化氧化去除水中4-氯酚实验。试验结果表明:制备的铁氧化物为纯Fe3O4,具有反尖晶石八面体结构。纳米Fe3O4能够高效催化H2O2分解氧化水中的4-氯酚,反应180 min后4-氯酚的去除率达到96.8%。当催化剂投量小于2.0 g/L,4-氯酚的去除率随着催化剂投量的增加而升高;当催化剂投量大于2.0 g/L,去除率会随着投量的增加而降低。随着H2O2投量的增加,4-氯酚的去除率先升高后降低。溶液的初始pH对4-氯酚的去除影响较大,pH越低,去除速率和效率越高。重复使用5次以后,纳米Fe3O4仍然保持较高的催化活性。     

中学化学继续教育应强化实验研究

通过Ｚｎ与Ｃｕ（ＮＯ_３）_２溶液反应的实验分析,提出了研究和全面认识置换反应的思路。对中学化学教师继续教育中实验教学应解决的问题进行了讨论。     

界面改性对SiCp/Cu复合材料导热性能的影响*(复合材料专题)

采用磁控溅射法结合结晶化热处理工艺在碳化硅（Silicon Carbide, SiC）颗粒表面成功制备了金属钼（Molybdenum, Mo）涂层,分析了Mo涂层的成分和形貌;然后采用热压烧结工艺制备了SiCp/Cu复合材料,重点对比分析了Mo界面阻挡层厚度对复合材料导热性能的影响。结果表明：磁控溅射法能够在SiC颗粒表面沉积得到Mo 涂层,随溅射时间的延长Mo涂层的厚度增加、粗糙度增大,且磁控溅射后SiC颗粒表面直接得到的Mo涂层为非晶态,结晶化热处理后,变为致密平整的晶态Mo涂层。磁控溅射时间即Mo涂层厚度对复合材料导热性能影响明显,随磁控溅射时间的增加,复合材料的热导率呈现先增后减趋势,采用磁控溅射9h镀Mo改性并经过800℃结晶化热处理的SiC复合粉体在850℃下热压烧结制备的SiCp/Cu复合材料（VSiC=50%）,其热导率达到了最高值274.056W/(m·K)。     

Cu粉粒径及含量对Ni/MH电池负极放电性能的影响

为了提高Ni/MH电池中储氢电极的放电性能,以电解Cu粉为充填材料与活性物质混合制备电极,研究Cu粉粒径及含量对电极性能的影响。研究发现,Cu粉粒径越小,含量越高,电极的放电容量、高倍率放电性能、及在低温和高温下的放电能力均提高,且Cu充填电极的性能优于Ni充填电极。Cu充填电极中析氢反应的交换电流密度较大,过电势较小,说明其电催化活性好,电极反应阻力小。SEM分析发现,充放电循环后的Cu充填电极,其储氢合金颗粒表面覆盖着一层细小Cu颗粒和丝状物,这是电极性能提高的主要原因。     

Influence of high frequency pulse on electrode wear in micro-EDM

An electromagnetic coupling mathematical model is established by finite element method and is verified by the contrastive experiments of copper matrix Ni–TiN cylindrical coating electrode, copper electrode and Cu50W electrode. The wear mechanism of Ni–TiN/Cu composite electrode in the case of high-frequency pulse current is studied, and the influence of the fluctuation frequency of discharge current on electrode wear in micro-EDM is found out. Compared with the electrode made from homogeneous material, the high frequency electromagnetic properties of Ni–TiN composite layer can be used effectively to inhibit the effect of high frequency pulse on the electrode and improve the distribution trend of current density.     

纳米粒子在油品中的抗磨性能研究与分析

采用四球试验机研究Cu、Zn(OH)2和PbO3种不同纳米粒子的摩擦性能,探讨纳米粒子在油品中的润滑作用机理。结果表明:纳米粒子在油品中抗磨作用的发挥存在载荷临界点;只有当载荷高于临界载荷时,纳米粒子才能表现出良好的摩擦学性能。     

界面改性对SiCp/Cu复合材料导热性能的影响

采用磁控溅射法结合结晶化热处理工艺在SiC颗粒表面成功制备了金属Mo涂层,分析Mo涂层的成分和形貌;采用热压烧结工艺制备SiCp/Cu复合材料,重点对比分析Mo界面阻挡层厚度对复合材料导热性能的影响。结果表明:磁控溅射法能够在SiC颗粒表面沉积得到Mo涂层,随溅射时间的延长,Mo涂层的厚度增加、粗糙度增大,且磁控溅射后SiC颗粒表面直接得到的Mo涂层为非晶态,结晶化热处理后,变为致密平整的晶态Mo涂层。磁控溅射时间对Mo涂层厚度和复合材料导热性能影响明显。随磁控溅射时间的增加,复合材料的热导率呈先增后减趋势。采用磁控溅射9h镀Mo改性并经过800℃结晶化热处理的SiC复合粉体在850℃下热压烧结制备的SiCp/Cu复合材料(VSiC=50%),其热导率达到了最高值274.056W/(m·K)。     

非均匀形核法制备Cu包覆纳米SiO2复合粉体

采用非均匀形核法制备了Cu包覆纳米SiO2复合颗粒,利用X射线衍射仪、扫描电镜、能谱仪及透射电镜等分析手段对复合颗粒进行了表征,并探讨了包覆结构的形成机制。结果表明:复合颗粒分散均匀,无团聚,单颗粒内包含多个分布均匀的纳米SiO2颗粒,且均被Cu包覆层隔离,纳米SiO2颗粒的分散性得到了显著改善;新制备的复合颗粒不存在氧化,在存放或者制样过程中会部分氧化为Cu2O;纳米SiO2颗粒表面Cu包覆层的形成机制主要是非均匀形核作用,包覆的结构取决于 Cu晶粒在纳米SiO2颗粒表面的沉积以及对复合颗粒的团聚控制。     

纳米铜润滑油添加剂的制备及其性能研究

采用KBH4液相还原法制备了具有面心立方结构,粒径约为40nm的纳米铜颗粒。利用环块摩擦磨损试验机考察了其作为添加剂在不同润滑油中的摩擦学性能,利用SEM、EDS等对摩擦表面进行了形貌、成分分析,探讨了纳米铜颗粒作为添加剂的作用机理。