提高聚氨酯推进剂基体粘结强度的途径探索

聚氨酯的水解稳定性较差,粘结强度偏低。将端羟基聚丁二烯与聚氨酯进行共混改性,提高了聚氨酯基体的表观交联度及推进剂的拉伸强度。采用示差扫描量热法和红外光谱法分析基体共混物的微观结构,表明这是提高聚氨酯基体粘结强度的一条有效途径。     

沥青纤维不熔化过程的红外光声光谱研究

沥青纤维在其不熔化过程中,发生了一系列复杂的化学变化。本文应用红外光声光谱法,分析研究沥青纤维以空气作不熔化介质,在不同温度下,所得一系列沥青不熔化纤维的组成与结构的变化     

A BENDING DAMAGE THEORY FOR BEAMS UNDER PURE BENDING LOADS

ＡＢＥＮＤＩＮＧＤＡＭＡＧＥＴＨＥＯＲＹＦＯＲＢＥＡＭＳＵＮＤＥＲＰＵＲＥＢＥＮＤＩＮＧＬＯＡＤＳＹａｎｇＧｕａｎｇｓｏｎｇ;ＬｕＹｉｎｃｈｕ;ＪｉｎＸｉｎ（ＤｅｐａｒｔｍｅｎｔｏｆＡｅｒｏｓｐａｃｅＴｅｃｈｎｏｌｏｇｙ,ＮＵＤＴ,Ｃｈａｎｇｓｈａ,...     

锁相放大器在光纤陀螺信号检测中的应用

讨论了光纤陀螺信号检测的基本原理,分析了锁相放大器参数选择对测试结果的影响。在干涉型去偏光纤陀螺系统中应用锁相放大器进行信号检测,可使系统阈值达到0.1deg/h,零漂达到0.4deg/h.     

拉压异性材料楔体的极限载荷分析

利用莫尔屈服准则,对一侧承受均布垂直载荷作用的拉压异性材料楔体进行了极限载荷分析。计算结果表明,考虑了材料的拉压异性影响,楔体承受的极限载荷有明显提高。     

机械零件可靠性在应力-强度分布特性下的计算模型

根据应力-强度分布特性下的干涉理论,确定了机械零件在应力-强度诸分布情形下的可靠性计算模型,将应力、强度、结构和可靠性计算联系起来。     

Enhancing the explosive characteristics of a Semtex explosive by involving admixtures of BCHMX and HMX

A well-known ternary plastic explosive, Czech Semtex 1H, contains a mixture of PETN and RDX softened by SBR. In this work, BCHMX was used to replace PETN in Semtex 1H to form Sem-BC+RDX. In addition, another mixture based on BCHMX and HMX as energetic fillers bonded by the polymeric matrix of Semtex 1H (Sem-BC+HMX) was studied. The particle size distribution of each individual explosive was determined to obtain the optimum mixing conditions. Friction and impact sensitivities were determined. The velocity of detonation was reported practically and the detonation properties were calculated by EXPLO5 code. The explosive strength of each sample was measured by the ballistic mortar test. The conclusion confirms that the velocity of detonation of Sem-BC+HMX was the highest in comparison with the prepared samples. Sem-BC+RDX has the least impact and frictions sensitivities. Sem-BC+RDX has higher detonation velocity, detonation properties and explosive strength than Semtex 1H. Addition of BCHMX in Semtex 1H as a replacement for PETN is the candidate to produce a high performance advanced Czech plastic explosive.     

An investigation on anti-impact and penetration performance of basalt fiber composites with different weave and lay-up modes

The woven basalt fiber composites (WBFC) and the unidirectional [0°/90°/45°/-45°]_s basalt fiber composites (UBFC) were prepared by hot-pressing. Three-point bending test, low velocity impact test, and ballistic test were performed to the prepared composites. After the tests, the specimens were recovered and analyzed for micromorphology. Three-point bending tests show that both the bending strength and stiffness of the WBFC surpass those of the UBFC. Low velocity impact test results show that the low velocity impact resistance to hemispherical impactor of the UBFC is higher than that of the WBFC, but the low velocity impact resistance to sharp impactor of the UBFC is lower than that of the WBFC. For the ballistic test, it can be found that the ballistic property of the UBFC is higher than that of the WBFC. After the tests, microscopic analysis of the specimens was applied, and their failure mechanism was discussed. The main failure modes of the UBFC are delamination and fibers breakage under the above loading conditions while the main failure mode of the WBFC is fibers breakage. Although delamination damage can be found in the WBFC under the above loading conditions, the degree of delamination is far less than that of the UBFC.     

【专栏】飞机结构静强度应变现场测试手段展望

目前飞机结构静强度应变现场主要的测试手段为使用电阻应变计测量系统,但电阻应变计测量系统存在抗电磁干扰差、引线过多以及一致性难以保证等问题,测试效果难以保证。近年来,光纤传感以及非接触光学测量手段的迅速发展,为飞机结构静强度应变现场测试提供了多种选择。本文通过分析以数字图像相关法技术为代表的新技术的特点,如通过进行非接触操作消除安装过程中所带来的分散性误差以及不确定性,在应对某些需要定性分析的飞机静强度试验场合时可以实时给出三维应变和位移场数据,使测量技术更加直观,以及可溯源性更好、更容易保证计量特性的稳定等,对未来飞机结构静强度应变现场测试手段进行了展望,以期为相关部门和机构提供参考。     

炮闩闩体击针孔强度仿真计算与结构改进

从击针和闩体的装配结构关系入手,在闩体击针室受力分析的基础上,进行了闩体有限元分析,得到了击针室两个不同部位受力时闩体击针孔处的应力和应变情况,从而提出解决闩体镜面击针孔产生凸出或裂纹问题的可行方案。