聚能射流形成过程的理论建模与分析

分析了聚能射流的形成过程,并对其中的各阶段进行了详细建模。在模型中考虑了炸药爆轰、金属的驱动、药型罩压垮以及射流和杵体的形成过程。采用该模型对某一聚能装药结构进行了计算,计算结果表明:药型罩顶部和底部微元的压垮速度较小,在射流头部形成反向速度梯度,与试验数据吻合较好。该模型对于多级侵彻战斗部的工程设计与侵彻参数的计算具有一定的参考价值。     

Effect of wave shaper on reactive materials jet formation and its penetration performance

Wave shaper effect on formation behavior and penetration performance of reactive liner shaped charge (RLSC) are investigated by experiments and simulations. The reactive materials liner with a density of 2.3 g/cm³ is fabricated by cold pressing at a pressure of 300 MPa and sintering at a temperature of 380 °C. Experiments of the RLSC with and without wave shaper against steel plates are carried out at standoffs of 0.5, 1.0, and 1.5 CD (charge diameter), respectively. The experimental results show that the penetration depths and structural damage effects of steel plates decrease with increasing the standoff, while the penetration depths and the damage effects of RLSC without wave shaper are much greater than that with wave shaper at the same standoff. To understand the unusual experimental results, numerical simulations based on AUTODYN-2D code are conducted to discuss the wave shaper effect, including the propagation behavior of detonation wave, the velocity and temperature distribution of reactive jet, and penetration depth of reactive jet. The simulations indicate that, compared with RLSC without wave shaper, there is a higher temperature produced inside reactive jet with wave shaper. This unusual temperature rise effects are likely to be an important mechanism to cause the initiation delay time of reactive jet to decline, which results in significantly decreasing its penetration performance.     

局部多孔质气浮止推轴承特性研究

在考虑轴承气膜交界面处切向速度滑移的条件下,建立了局部多孔质气浮止推轴承的理论模型,然后使用有限元算法进行了数值仿真,仿真的结果与试验结果取得了一定程度的一致性,说明此新的修改了的雷诺方程可以用来作为局部多孔质气浮止推轴承研究的理论模型。利用该模型,能够成功计算出不同渗透系数、不同厚度及不同直径的局部多孔质气浮轴承的流量、承载及刚度。还从理论上与小孔类型及全多孔质类型的气浮轴承特性进行了对比,结果表明,局部多孔质气浮轴承有着优良的特性及很好的应用前景。     

三维均匀化理论预测多孔混凝土等效弹性模量

应用多尺度渐进展开的均匀化理论,推导三维均匀化理论的有限元解法,求解复合材料等效弹性系数。假设多孔混凝土由光滑均匀一致的球孔与水泥石基质组成,提出改进的随机投放方法,生成三维均匀化理论求解的随机单胞模型。以聚苯乙烯泡沫(EPS)混凝土为数值算例,生成6组不同体积分数的EPS混凝土随机单胞模型,通过三维均匀化理论的有限元法计算得到其等效弹性模量。计算结果表明:随机单胞模型能反映细观的非均质性,三维均匀化理论的有限元法计算得到的等效弹性模量变化趋势比较符合Miled的试验结果。     

多爆炸成型弹丸性能参数灰关联分析

为了获得各参数对多爆炸成型弹丸毁伤性能的影响程度,以EFP速度和MEFP发散角为参考序列,以药型罩和装药参数为比较序列,运用灰关联理论对影响MEFP毁伤性能的参数进行了灰关联分析。在此基础上,应用灰关联分析结果完成了MEFP战斗部优化设计。结果表明:在较少样本空间前提下,采用灰关联理论可以分析获得影响多爆炸成型弹丸毁伤性能的各因素主次关系,而且经过优化后的MEFP战斗部,大大地提高了EFP的集聚性和毁伤性能。     

A study on the surface overpressure distribution and formation of a double curvature liner under a two-point initiation

The formation mechanism of an EFP(explosively formed projectile) using a double curvature liner under the overpressure effect generated by a regular oblique reflection was investigated in this paper.Based on the detonation wave propagation theory,the change of the incident angle of the detonation wave collision at different positions and the distribution area of the overpressure on the surface of the liner were calculated.Three-dimensional numerical simulations of the formation process of the EFP with tail as well as the ability to penetrate 45# steel were performed using LS-DYNA software,and the EFP ve-locity,the penetration ability,and the forming were assessed via experiments and x-ray photographs.The experimental results coincides with those of the simulations.Results indicate that the collision of the detonation wave was controlled to be a regular oblique reflection acting on the liner by setting the di-mensions of the unit charge and maintaining the pressure at the collision point region at more than 2.4 times the CJ detonation when the incident angle approached the critical angle.The distance from the liner midline to the boundary of the area within which the pressure ratio of the regular oblique reflection pressure to the CJ detonation pressure was greater than 2.5,2,and 1.5was approximately 0.66 mm,1.32 mm,and 3.3 mm,respectively.It is noted that pressure gradient caused the liner to turn inside out in the middle to form the head of the EFP and close the two tails of the EFP at approximately 120μs.The penetration depth of the EFP into a 45# steel target exceeded 30 mm,and there was radial expansion between the head and tail of the EFE increasing the penetration resistance of the EFP.Therefore,the structural size of the unit charge and the liner can be further optimized to reduce resistance to increase the penetration ability of the EFP.     

电子探针在电气火灾物证技术鉴定中的应用

在介绍电子探针分析技术的功能和特点的基础上,结合火灾案例说明了电子探针技术在导线熔痕电子显微形貌观察及熔痕微孔表层成分分析中的应用.通过分析,从导线短路熔痕的微观形貌、熔痕孔洞表层的特征元素含量中获得其熔痕形成原因,进而为火灾调查提供技术支持.     

基于多信息的柴油机缸套磨损故障诊断研究

采用了模糊神经网络模型,对柴油机缸套磨损故障以及缸套破坏性磨损故障进行了诊断研究.通过缸套磨损故障的模拟实验,获取柴油机机身振动和铁谱分析等多源多维故障信息,并对融合故障信息进行预处理,解决了模糊神经网络输入矢量的模糊特性化、输出矢量的隶属函数及网络的学习训练问题,对缸套不同磨损故障进行了诊断.研究表明,这种基于多信息的诊断方法减小了故障诊断的不确定性,提高了诊断精度.     

多孔材料药型罩聚能射流的形成条件

依据Herrmann状态方程和斜冲击波关系估算了多孔材料药型罩压垮之前的冲击温升,求解了经过冲击压缩卸载后材料的声速。给出了多孔材料药型罩聚能射流的形成条件。初始冲击温升会使材料的声速和强度降低,从而使多孔材料聚能射流形成射流的高速和低速条件降低。     

瞬态高强加热条件下含湿多孔介质传热传质模型研究

提出了瞬态高强加热下含湿多孔介质传热传质的新模型,模型包括的水分种类齐全、水分迁移机制全面,假设条件相对较少,考虑了非Fourier传热效应和非Fick传质效应。新模型通过具体的分区分析得到简化并更加实用。