AZ91D镁合金表面纳米TiO_2复合微弧氧化层耐蚀性能研究

为了提高AZ91D镁合金微弧氧化陶瓷层的耐蚀能力,采用Na2SiO3电解液,添加入纳米TiO2,经微弧氧化,纳米TiO2颗粒复合入陶瓷层中,形成表面质量良好的纳米复合陶瓷质氧化膜。通过与普通微弧氧化陶瓷层比较,结果表明：纳米TiO2复合微弧氧化陶瓷层孔隙率降低,致密性提高,抗盐雾腐蚀性能提高1倍以上。     

Low velocity impact studies of E-glass/epoxy composite laminates at different thicknesses and temperatures

Low velocity impact experiments were carried out on E-glass/epoxy composite laminates having varying thicknesses at sub zero and elevated temperatures using hemi spherical steel impactor of 16 mm diameter with impact energies in the rage of 50–150 J. The performance of the laminates was assessed in terms of energy absorption, maximum displacement, peak force and failure behaviour. Results indicated that the effect of temperature on energy absorption of the laminate is negligible although the laminates are embrittling at sub zero temperatures. However it has influence on failure behaviour and displacement. Peak force has increased linearly with increase in laminate thickness from 5 to 10 mm. However it got reduced by 25% when temperature was increased from −20 °C to 100 °C. Based on experimental results, laminate perforation energies were predicted using curve fitting equations. Statistical analysis was carried out using Taguchi method to identify the global effects of various parameters on laminate performance and confirmed that the laminate thickness has significant influence as compared to temperature, for the studied range.     

Fabrication of AA7005/TiB2-B4C surface composite by friction stir processing: Evaluation of ballistic behaviour

The present work aims to enhance the ballistic resistance of AA7005 alloy by incorporating the TiB₂ and B₄C ceramic reinforcement particles. Surface composites with different weight fractions of TiB₂ and B₄C particles were processed by friction stir processing. Micro-hardness and depth of penetration tests were carried out to evaluate the ballistic properties of the surface composites. The surface hardness of the composite was found to be nearly 70 HV higher than base alloy. The depth of penetration of the steel projectile was 20–26 mm in the composites as compared to 37 mm in the base alloy. Ballistic mass efficiency factor of the surface composite was found to be 1.6 times higher than base alloy. This is mainly attributed to the dispersion strengthening from the reinforcement particles.     

Effect of tool pin profile on microstructure and tensile properties of friction stir welded dissimilar AA 6061e AA 5086 aluminium alloy joints

Joints between two different grades of aluminium alloys are need of the hour in many light weight military structures.In this investigation,an attempt has been made to join the heat treatable(AA 6061) and non-heat treatable(AA 5086) aluminium alloys by friction stir welding(FSW)process using three different tool pin profiles like straight cylindrical,taper cylindrical and threaded cylindrical.The microstructures of various regions were observed and analyzed by means of optical and scanning electron microscope.The tensile properties and microhardness were evaluated for the welded joint.From this investigation it is founded that the use of threaded pin profile of tool contributes to better flow of materials between two alloys and the generation of defect free stir zone.It also resulted in higher hardness values of 83 HV in the stir zone and higher tensile strength of 169 MPa compared to other two profiles.The increase in hardness is attributed to the formation of fine grains and intermetallics in the stir zone,and in addition,the reduced size of weaker regions,such as TMAZ and HAZ regions,results in higher tensile properties.     

抗超高速撞击多层结构复合材料研究

本文介绍了抗超高速撞击多层结构复合材料的设计、制备和实验,并对结果进行了讨论,实验证明,以SiC陶瓷基复合材料为防护层、以空心微珠或多孔变密度复合材料为缓冲层、以编织物复合材料为结构层的多层结构复合材料,具有面密度低、抗撞击速度范围宽、抗撞击性能好的特点。     

Comparative study on transverse shrinkage,mechanical and metallurgical properties of AA2219 aluminium weld joints prepared by gas tungsten arc and gas metal arc welding processes

Aluminium alloy AA2219 is a high strength alloy belonging to 2000 series. It has been widely used for aerospace applications, especially for construction of cryogenic fuel tank. However, arc welding of AA2219 material is very critical. The major problems that arise in arc welding of AA2219 are the adverse development of residual stresses and the re-distribution as well as dissolution of copper rich phase in the weld joint.These effects increase with increase in heat input. Thus, special attention was taken to especially thick section welding of AA2219-T87 aluminium alloy. Hence, the present work describes the 25 mm-thick AA2219-T87 aluminium alloy plate butt welded by GTAW and GMAW processes using multi-pass welding procedure in double V groove design. The transverse shrinkage, conventional mechanical and metallurgical properties of both the locations on weld joints were studied. It is observed that the fair copper rich cellular(CRC) network is on Side-A of both the weldments. Further, it is noticed that, the severity of weld thermal cycle near to the fusion line of HAZ is reduced due to low heat input in GTAW process which results in non dissolution of copper rich phase. Based on the mechanical and metallurgical properties it is inferred that GTAW process is used to improve the aforementioned characteristics of weld joints in comparison to GMAW process.     

Enhancement of wear and ballistic resistance of armour grade AA7075 aluminium alloy using friction stir processing

Industrial applications of aluminium and its alloys are restricted because of their poor tribological properties. Thermal spraying, laser surfacing, electron beam welding are the most widely used techniques to alter the surface morphology of base metal. Preliminary studies reveal that the coating and layering of aluminium alloys with ceramic particles enhance the ballistic resistance. Furthermore, among aluminium alloys,7075 aluminium alloy exhibits high strength which can be compared to that of steels and has profound applications in the designing of lightweight fortification structures and integrated protection systems. Having limitations such as poor bond integrity, formation of detrimental phases and interfacial reaction between reinforcement and substrate using fusion route to deposit hard particles paves the way to adopt friction stir processing for fabricating surface composites using different sizes of boron carbide particles as reinforcement on armour grade 7075 aluminium alloy as matrix in the present investigation. Wear and ballistic tests were carried out to assess the performance of friction stir processed AA7075 alloy. Significant improvement in wear resistance of friction stir processed surface composites is attributed to the change in wear mechanism from abrasion to adhesion. It has also been observed that the surface metal matrix composites have shown better ballistic resistance compared to the substrate AA7075 alloy. Addition of solid lubricant Mo S2 has reduced the depth of penetration of the projectile to half that of base metal AA7075 alloy. For the first time, the friction stir processing technique was successfully used to improve the wear and ballistic resistances of armour grade high strength AA7075 alloy.     

Microstructure and pitting corrosion of armor grade AA7075 aluminum alloy friction stir weld nugget zone-Effect of post weld heat treatment and addition of boron carbide

Friction stir welding(FSW) of high strength aluminum alloys has been emerged as an alternative joining technique to avoid the problems during fusion welding.In recent times FSW is being used for armor grade AA7075 aluminum alloy in defense,aerospace and marine applications where it has to serve in non uniform loading and corrosive environments.Even though friction stir welds of AA7075 alloy possess better mechanical properties but suffer from poor corrosion resistance.The present work involves use of retrogression and reaging(RRA) post weld heat treatment to improve the corrosion resistance of welded joints of aluminum alloys.An attempt also has been made to change the chemical composition of the weld nugget by adding B4C nano particles with the aid of the FSW on a specially prepared base metal plate in butt position.The effects of peak aged condition(T6),RRA and addition of B4C nano particles on microstructure,hardness and pitting corrosion of nugget zone of the friction stir welds of AA7075 alloy have been studied.Even though RRA improved the pitting corrosion resistance,its hardness was slightly lost.Significant improvement in pitting corrosion resistance was achieved with addition of boron carbide powder and post weld heat treatment of RRA.     

Optimization of process parameters of aluminum alloy AA 2014-T6 friction stir welds by response surface methodology

The heat treatable aluminum-copper alloy AA2014 finds wide application in the aerospace and defence industry due to its high strength-toweight ratio and good ductility. Friction stir welding(FSW) process, an emerging solid state joining process, is suitable for joining this alloy compared to fusion welding processes. This work presents the formulation of a mathematical model with process parameters and tool geometry to predict the responses of friction stir welds of AA 2014-T6 aluminum alloy, viz yield strength, tensile strength and ductility. The most influential process parameters considered are spindle speed, welding speed, tilt angle and tool pin profile. A four-factor, five-level central composite design was used and a response surface methodology(RSM) was employed to develop the regression models to predict the responses.The mechanical properties, such as yield strength(YS), ultimate tensile strength(UTS) and percentage elongation(%El), are considered as responses. Method of analysis of variance was used to determine the important process parameters that affect the responses. Validation trials were carried out to validate these results. These results indicate that the friction stir welds of AA 2014-T6 aluminum alloy welded with hexagonal tool pin profile have the highest tensile strength and elongation, whereas the joints fabricated with conical tool pin profile have the lowest tensile strength and elongation.     

B4C/Al复合板中应力波行为分析（Ⅰ）

依据7.62mm穿甲燃烧弹与B4C,Al板的物理和力学特性,提出弹、板的力学模型;在此基础上,给出弹板碰撞后B4C/Al复合板的弹性动力学方程,建立应力波的传播模型,讨论了应力波传播时复合板的力学行为,最后确定了复合板承受的初始冲击应力。理论分析表明：一维应变条件的B4C和Al板的弹性极限高于一维应力条件下的值;弹、板间的作用力服从指数衰减规律;B4C板的初始应力高于430MPa时,应力波的作用使Al板在卸载过程中发生反向屈服。     

Development of cost effective personnel armour through structural hybridization

The objective of the present study is to develop cost effective thermoplastic hybrid laminate using Dyneema® HB50 and Tensylon®HSBD 30A through structural hybridization method. Laminates having 20 mm thickness were fabricated and subjected to 7.62 × 39 mm mild steel core projectile with an impact velocity of 730 ± 10 ms⁻¹. Parameters such as energy absorption, back face deformation and rate of back face deformation were measured as a function of hybridization ratio. It was observed that hybrid laminate with 50:50 ratio (w/w) of Tensylon® and Dyneema® with Tensylon® as front face showed 200% more energy absorption when compared to 100% Tensylon® laminate and showed equal energy absorption as that of expensive 100% Dyneema® laminate. Moreover, hybrid laminate with TD50:50 ratio showed 40% lower in terms of final back face deformation than Dyneema® laminate. Rate of back face deformation was also found to be slow for hybrid laminate as compared to Dyneema® laminate. Dynamic mechanical analysis showed that, Tensylon® laminate has got higher stiffness and lower damping factor than Dyneema® and hybrid laminates. The interface between Tensylon® and Dyneema® layers was found to be separating during the penetration process due to the poor interfacial bonding. Failure behaviour of laminates for different hybridization ratios were studied by sectioning the impacted laminates. It was observed that, the Tensylon® laminate has undergone shear cutting of fibers as major failure mode whereas the hybrid laminate showed shear cutting followed by tensile stretching, fiber pull out and delamination. These inputs are highly useful for body armour applications to design cost effective armour with enhanced performance.     

Effect of friction stir processing on mechanical properties and heat transfer of TIG welded joint of AA6061 and AA7075

Tungsten inert gas (TIG) welding is the most commonly used joining process for aluminum alloy for AA6061 and AA7075 which are highly demanded in the aerospace engineering and the automobile sector, but there are some defects occur during TIG welding like micro-crack, coarse grain structure, and porosity. To improve these defects, the TIG welded joint is processed using friction stir processing (FSP). This paper presents the effect of friction stir processing on TIG welding with filler ER4043 and ER 5356 for dissimilar aluminum alloy AA6061 and AA7075. The mechanical characterization, finite element formulation and mathematical equations of heat transfer of TIG + FSP welded joints are investigated using ANSYS Fluent software by adjusting process parameters of FSP. The results show that the maximum compressive residual stress 73 MPa was obtained at the fusion zone (FZ) of the TIG weldment with filler ER4043, whereas minimum compressive residual stress 37 MPa was obtained at stir zone (SZ) of the TIG+FSP with filler 5356. The maximum heat flux 5.33 × 106 W/m2 and temperature 515 ℃ have observed at tool rotation 1600 rpm with a feed rate of 63 mm/min. These results give a satisfactory measure of confidence in the fidelity of the simulation     

Microstructure,mechanical and corrosion behavior of high strength AA7075aluminium alloy friction stir welds-Effect of post weld heat treatment

High strength aluminium alloy AA7075(Al-Zn-Mg-Cu) is a precipitate hardenable alloy widely used in the aerospace,defense,marine and automobile industries.Use of the heat treatable aluminium alloys in all these sectors is ever-increasing owing to their excellent strength-toweight ratio and reasonably good corrosion resistance.The shortage in corrosion resistance,however,usually poses negative concern about their reliability and lifetime when they service in the variable marine environments.These alloys also exhibit low weldability due to poor solidification microstructure,porosity in fusion zone and lose their mechanical properties when they are welded by fusion welding techniques.Friction stir welding(FSW) is a reliable technique to retain the properties of the alloy as the joining takes place in the solid state.The welds are susceptible to corrosion due to the microstructural changes in the weld nugget during FSW.In this work,the effect of post weld treatments,viz.,peak aging(T6) and retrogression reaging(RRA),on the microstructure,mechanical properties and pitting corrosion has been studied.Friction stir welding of 8 mm-thick AA7075 alloy was carried out.The microstructural changes of base metal and nugget zone of friction stir welds were studied using optical microscopy,scanning electron microscopy and transmission electron microscopy.Tensile and hardness test of base metal and welds has been carried out.Pitting corrosion resistance was determined through dynamic polarization test.It was observed that the hardness and strength of weld were observed to be comparatively high in peak aged(T6) condition but the welds showed poor corrosion resistance.The resistance to pitting corrosion was improved and the mechanical properties were maintained by RRA treatment.The resistance to pitting corrosion was improved in RRA condition with the minimum loss of weld strength.     

Effect of tool rotational speed on the particle distribution in friction stir welding of AA6092/17.5 SiCp-T6 composite plates and its consequences on the mechanical property of the joint

This study investigates the effect of tool rotational speed (TRS) on particle distribution in nugget zone (NZ) through quantitative approach and its consequences on the mechanical property of friction stir welded joints of AA6092/17.5 SiC_p-T6 composite. 6 mm thick plates are welded at a constant tool tilt angle of 2° and tool traverse speed of 1 mm/s by varying the TRS at 1000 rpm, 1500 rpm and 2000 rpm with a taper pin profiled tool. Microstructure analysis shows large quantity of uniformly shaped smaller size SiC particle with lower average particle area which are homogeneously distributed in the NZ. The fragmentation of bigger size particles has been observed because of abrading action of the hard tool and resulting shearing effect and severe stress generation due to the rotation of tool. The particles occupy maximum area in the matrix compared to that of the base material (BM) due to the redistribution of broken particles as an effect of TRS. The migration of particles towards the TMAZ-NZ transition zone has been also encountered at higher TRS (2000 rpm). The microhardness analysis depicts variation in average hardness from top to bottom of the NZ, minimum for 1500 rpm and maximum for 2000 rpm. The impact strength at 1000 rpm and 1500 rpm remains close to that of BM (21.6 J) while 2000 rpm shows the accountable reduction. The maximum joint efficiency has been achieved at 1500 rpm (84%) and minimum at 1000 rpm (68%) under tensile loading. Fractographic analysis shows mixed mode of failure for BM, 1000 rpm and 1500 rpm, whereas 2000 rpm shows the brittle mode of failure.     

冲击波在多层结构中的传播

对水下冲击载荷在多层结构中的传播规律进行了理论分析,根据分界面上的应力和速度连续性条件得到透射波强度的解析表达式.从理论分析可以看出,舰船结构的多层防护体系对于减少爆炸冲击的损伤具有重要的作用,防护结构的波阻抗越大,防护的效果越好,这种方法可应用于多层防护结构在远场爆炸冲击波作用下的毁伤或防护方面的预测.     

高速电弧喷涂FeCrBSiMnNbW非晶纳米晶涂层组织及性能

研究开发了一种FeCrBSiMnNbW新型喷涂粉芯丝材,并采用自动化高速电弧喷涂技术在镁合金基体上制备了FecrBsiMnNbw非晶纳米晶涂层。对Fe基非晶纳米晶涂层和传统的3Cr13涂层的组织结构、力学性能以及油润滑条件下的摩擦学性能进行了对比分析,结果表明：与3Cr13涂层相比,铁基非晶纳米晶涂层组织更加致密,孔隙率低,具有相对较高的硬度和拉伸结合强度;形成了非晶相和纳米晶相组成的复合结构,使得涂层具备更好的摩擦学性能。     

H2O2对镁合金稀土转化膜性能的影响

选择AZ91D镁合金为实验材料,利用扫描电镜和能谱分析、Tafel曲线和阻抗谱等分析手段,研究了H2O2的添加量对铈转化膜的微观形貌以及耐蚀性能的影响。结果表明：随H2O2添加量的增多,转化膜表面状态越不均匀,自腐蚀电位降低,转化膜电阻Rf变小,较为合适的H2O2添加量为5 mL/L。     

LiDAR点云纹理特征提取方法

针对图像纹理应用于LiDAR点云分类过程中存在的多义性问题，提出点云纹理特征的概念。该特征属性反映了点与其邻域点的属性值分布情况，提取过程基于KD树数据检索结构和灰度共生矩阵算法。分析搜索邻域、移动步长和灰度等级等参数对点云纹理特征的影响，并利用支持向量机分类方法验证点云纹理特征，可以有效地辅助高程和强度信息以改善LiDAR点云的地物分类结果。实验还证明了相比于栅格格式的图像纹理特征，点云纹理特征约束的地物分类具有更高的分类精度，并且点云纹理特征在微小地物的甄别和水陆的区分方面具有突出的能力。该特征的这些优秀特性可以为海岸带机载LiDAR数据的精细化分类、海岸带高精度DEM构建和海岸线提取等工作发挥重要作用。     

Influence of process parameters on physical dimensions of AA6063 aluminium alloy coating on mild steel in friction surfacing

An attempt is made in the present study to obtain the relationships among process parameters and physical dimensions of AA6063 aluminium alloy coating on IS2062 mild steel obtained through friction surfacing and their impact on strength and ductility of the coating. Factorial experimental design technique was used to investigate and select the parameter combination to achieve a coating with adequate strength and ductility. Spindle speed, axial force and table traverse speed were observed to be the most significant factors on physical dimensions. It was observed that the thickness of the coating decreased as the coating width increased. In addition, the width and thickness of the coatings are higher at low and high torques. At intermediate torque values, when the force is high, the width of the coating is high, and its thickness is thin; and when the force is low, the width and thickness are low. The interaction effect between axial force(F)-table traverse speed(Vx) and spindle speed(N)-table traverse speed(Vx) produced an increasing effect on coating width and thickness, but other interactions exhibited decreasing influence. It has also been observed that sound coatings could be obtained in a narrow set of parameter range as the substrate-coating materials are metallurgically incompatible and have a propensity to form brittle intermetallics.     

多轴向织物层合板层间剪切强度有限元分析与实验研究

用VIMP工艺制备了UD、0/45/-45、0/45/90/-45三种多轴向织物增强,四种厚度的GFRP层合板试样,采用短梁剪切实验考察了层间剪切强度和破坏模式。建立了GFRP层合板短梁剪切试样有限元模型,计算了内部层间剪应力分布。结合计算和实验结果分析表明层合板存在由宽度方向层间剪应力变化导致的自由边缘效应,含偏轴铺层的层合板更容易发生边缘开裂破坏。厚度相同时0/45/-45多轴向织物增强层合板的层间剪切强度最高。短梁剪切强度测试存在尺寸效应,随着厚度的增加,强度下降,样品波动系数增大。