Experimental study on explosion dispersion process of a multi-layer composite charge under different initiation modes

The influence of initiation modes on the explosive dispersion process of the multi-layer composite charge (MCC) was studied. Overpressure sensors and high-speed photography system were used to investigate the energy release process of an MCC with a specific structure. The shock wave pressure and explosive dispersion characteristics of the MCC under different initiation modes were compared. The forming and expanding process of the shock wave of the composite charge under different initiation modes was determined. The separation position of the shock wave and fireball interface was determined. The calculation formulas of the shock radius and overpressure of the composite charge are presented. The radius of the shock wave of the composite charge was significantly affected by the initiation mode. Moreover, the development process of the composite explosive fireball under different initiation modes was analyzed, the variation rules of the composite charge dispersion radius and fireball dispersion velocity with time were obtained under the different initiation modes, the explosion energy release rate of composite charge under simultaneous initiation modes was the highest, and the peak overpressure under the simultaneous initiation mode was 1.61 times that of central single-point initiation.     

Modeling of the whole process of shock wave overpressure of free-field air explosion

The waveform of the explosion shock wave under free-field air explosion is an extremely complex problem. It is generally considered that the waveform consists of overpressure peak, positive pressure zone and negative pressure zone. Most of current practice usually considers only the positive pressure. Many empirical relations are available to predict overpressure peak, the positive pressure action time and pressure decay law. However, there are few models that can predict the whole waveform. The whole process of explosion shock wave overpressure, which was expressed as the product of the three factor functions of peak, attenuation and oscillation, was proposed in the present work. According to the principle of explosion similarity, the scaled parameters were introduced and the empirical formula was absorbed to form a mathematical model of shock wave overpressure. Parametric numerical simulations of free-field air explosions were conducted. By experimental verification of the AUTODYN numerical method and comparing the analytical and simulated curves, the model is proved to be accurate to calculate the shock wave overpressure under free-field air explosion. In addition, through the model the shock wave overpressure at different time and distance can be displayed in three dimensions. The model makes the time needed for theoretical calculation much less than that for numerical simulation.     

Mitigation effects on the reflected overpressure of blast shock with water surrounding an explosive in a confined space

The mitigation of blast shock with water has broad application prospects. Understanding the mitigation effects on the reflected overpressure of the explosion shock with water surrounding an explosive in a confined space is of great significance for military explosives safety applications. To estimate the effects of the parameters on the reflected overpressure of blasted shock wave, a series of experiments were carried out in confined containers with spherical explosives immersed in a certain thickness of water, and numerical simulations were conducted to explore the corresponding mechanisms. The results reveal that the reflected overpressure is abnormally aggravated at a small scaled distance. This aggravation is due to the high impulse of the bulk accelerated water shell converted from the explosion. With increasing scaled distance, the energy will be gradually dissipated. The mitigation effects will appear with the dispersed water phase front impacting at a larger scaled distance, except in the case of a dense water phase state. A critical scaled distance range of 0.7—0.8 m/kg1/3 for effective mitigation was found. It is suggested that the scaled distance of space walls should be larger than the critical value for a certain water-to-explosive weight ratio range (5—20).     

Study on energy release characteristics of reactive material casings under explosive loading

Reactive Materials (RMs), a new material with structural and energy release characteristics under shock-induced chemical reactions, are promising in extensive applications in national defense and military fields. They can increase the lethality of warheads due to their dual functionality. This paper focuses on the energy release characteristics of RM casings prepared by alloy melting and casting process under explosive loading. Explosion experiments of RM and conventional 2A12 aluminum alloy casings were conducted in free field to capture the explosive fireballs, temperature distribution, peak overpressure of the air shock wave and the fracture morphology of fragments of reactive material (RM) warhead casings by using high-speed camera, infrared thermal imager temperature and peak overpressure testing and scanning electron microscope. Results showed that an increase of both the fireball temperature and air shock wave were observed in all RM casings compared to conventional 2A12 aluminum ally casings. The RM casings can improve the peak overpressure of the air shock wave under explosion loading, though the results are different with different charge ratios. According to the energy release characteristics of the RM, increasing the thickness of RM casings will increase the peak overpressure of the near-field air shock wave, while reducing the thickness will increase the peak overpressure of the far-field air shock wave.     

The Early Responses of Air-backed plate subjected to underwater explosion with aluminized explosives

This work aims to research the effects on the early responses of the air-backed plate subjected to the loading generated by the underwater explosion with aluminized explosives. The loading characteristics of underwater explosion for ideal explosive (TNT), aluminized explosives (RS211 and RBUL) are obtained experimentally. The tested aluminized explosives have different energy output compared with TNT. Based on the Taylor plate theory, the early responses of the air-backed steel plate affected by the measured loading is analyzed. The analytical results indicate that the pressure curve of the shock wave within 1 time decay constant is the main factor affecting the kick-off velocity of the plate when cavitation occurring. The velocity responses of the plate produced by the loading of RS211 and RBUL are obviously different with that of an equivalent TNT charge, which also indicates validity and suitability should be noticed in the case of substituting TNT for aluminized explosives. Moreover, the uncertainties in the responses of the plate produced by RS211 and RBUL are much larger than TNT.     

Effect of metal powders on explosion of fuel-air explosives with delayed secondary igniters

In order to improve the energy level of fuel air explosive(FAE) with delayed secondary igniters, high energetic metal powders were added to liquid fuels mainly composed of ether and isopropyl nitrate. Metal powders' explosive properties and reaction mechanisms in FAE were studied by high-speed video, pressure test system, and infrared thermal imager. The results show that compared with pure liquid fuels, the shock wave overpressure, maximum surface fireball temperature and high temperature duration of the mixture were significantly increased after adding high energetic metal powder. The overpressure values of the liquid-solid mixture at all measuring points were higher than that of the pure liquid fuels. And the maximum temperature of the fireball was up to 1700 ℃, which was higher than that of the pure liquid fuels. After replacing 30％of aluminum powder with boron or magnesium hydride, the shock wave pressure of the mixture was further increased. The high heat of combustion of boron and the hydrogen released by magnesium hydride could effectively increase the blast effect of the mixture. The improvement of the explosion performance of boron was better than magnesium hydride. It shows that adding high energetic metal powder to liquid fuels can effectively improve the explosion performance of FAE.     

A melt-cast Duan-Zhang-Kim mesoscopic reaction rate model and experiment for shock initiation of melt-cast explosives

A melt-cast Duan-Zhang-Kim (DZK) mesoscopic reaction rate model is developed for the shock initiation of melt-cast explosives based on the pore collapse hot-spot ignition mechanism. A series of shock initiation experiments was performed for the Comp B melt-cast explosive to estimate effects of the loading pressure and the particle size of granular explosive component, and the mesoscopic model is validated against the experimental data. Further numerical simulations indicate that the initial density and formula proportion greatly affect the hot-spot ignition of melt-cast explosives.     

Explosion temperature mapping of emulsion explosives containing TiH2 powders with the two-color pyrometer technique

In the study, the two-color pyrometer technique was used to measure the transient temperature field of emulsion explosives with different contents of TiH₂ powders. The experimental results showed that the introduction of TiH₂ powders could significantly increase the explosion temperature and fireball duration of emulsion explosive. When emulsion explosives were ignited, the average explosion temperature of pure emulsion explosive continuously decreased while emulsion explosives added with TiH₂ powders increased at first and then decreased. When the content of TiH₂ powders was 6 mass%, the explosion average temperature reached its maximum value of 3095 K, increasing by 43.7% as compared with that of pure emulsion explosive. In addition, the results of air blast experiment and explosion heat test showed that the variation trends of shock wave parameters, explosion heat and theoretical explosion temperature of emulsion explosives with different contents of TiH₂ powders were basically consistent with that of explosion temperature measured by the two-color pyrometer technique. In conclusion, the two-color pyrometer technique would be conducive to the formula design of emulsion explosive by understanding the explosion temperature characteristics.     

Numerical investigation of the shockwave overpressure fields of multi-sources FAE explosions

Shockwaves from fuel-air explosive (FAE) cloud explosions may cause significant casualties. The ground overpressure field is usually used to evaluate the damage range of explosion shockwaves. In this paper, a finite element model of multi-sources FAE explosion is established to simulate the process of multiple shockwaves propagation and interaction. The model is verified with the experimental data of a fourfold-source FAE explosion, with the total fuel mass of 340 kg. Simulation results show that the overpressure fields of multi-sources FAE explosions are different from that of the single-source. In the case of multi-sources, the overpressure fields are influenced significantly by source scattering distance and source number. Subsequently, damage ranges of overpressure under three different levels are calculated. Within a suitable source scattering distance, the damage range of multi-sources situation is greater than that of the single-source, under the same amount of total fuel mass. This research provides a basis for personnel shockwave protection from multi-sources FAE explosion.     

爆轰波在可压缩金属板面上斜反射初始参数的计算

本文计算了爆轰波在可压缩金属板面上斜反射时的初始参数。计算中选用的五种炸药是TNT(p_0为1.64g/cm~3,1.45g/cm~3)、RDX(p_0为1.59g/cm~3,1.76g/cm~3,1.80g/cm~3)、RDX/TNT(77/23)(p_0为1.75g/cm~3)、Pentolite(p_0为1.65g/cm~3,1.68g/cm~3)和B 炸药(p_0为1.71g/cm~3);三种介质是铁、铜和铝。     

Effects of nano-sized aluminum on detonation characteristics and metal acceleration for RDX-based aluminized explosive

Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the param-eters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0％to 15％,every 5％increase of aluminum resulted in about a 1.3％decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14％and 8％higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 μs throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12％and 2.9 μs higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80％of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.     

Effect of energy content of the nitraminic plastic bonded explosives on their performance and sensitivity characteristics

Information about the forty nine nitraminic plastic bonded explosives (PBXs) and different nitramines were collected. Fillers of these PBXs are nitramines 1,3,5-trinitro-1,3,5-triazinane (RDX) and β-1,3,5,7-tetranitro-1,3,5-tetrazocane (β-HMX), cis-1,3,4,6-tetranitro-octahydroimidazo-[4,5-d]imidazole (bicyclo-HMX, BCHMX) and ε-2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (ε-HNIW, CL-20) which are bonded by polyfluoro-elastomers, polydimethyl-siloxane, poly-glycidyl azide, polyisobutylene, polystyrene-butadiene, poly-acrylonitrile-butadiene and hydroxyl-terminated polybutadiene in addition to a melt cast compositions based on 2,4,6-trinitrotoluene. For thirty two of these PBXs the relationships are specified and analyzed between heats of their combustion and relative explosive strengths; by means of these relationships it might be possible to estimate, which groupings in the macromolecule of binder could be liable to their primary fission in the PBXs initiation. Similarly, for forty two of these explosives, the relationships are described and analyzed between their enthalpies of formation and impact sensitivities; here is especially attention paid to PBXs filled by BCHMX. Specific rate constants from Vacuum Stability Test (VST) of four nitramines and twenty PBXs are introduced into relationships with their enthalpies of formation. Regarding to all the mentioned cases, increasing of energy content of the studied explosives leads to increase of the relative explosive strength or initiation reactivity, respectively. Exception with the opposite trend, the outputs of VST are for BCHMX, where in PBXs are matrices with the esteric plasticizers or the energetic poly-glycidyl azide. Admixture of RDX or HMX, respectively, into the BCHX PBXs gives ternary PBXs whose thermal stability, in the sense of applied VST, is higher comparing to the original binary explosives.     

Numerical simulation of the blast wave of a multilayer composite charge

The numerical simulation of a blast wave of a multilayer composite charge is investigated. A calculation model of the near-field explosion and far-field propagation of the shock wave of a composite charge is established using the AUTODYN finite element program. Results of the near-field and far-field calculations of the shock wave respectively converge at cell sizes of 0.25–0.5 cm and 1–3 cm. The Euler––flux-corrected transport solver is found to be suitable for the far-field calculation after mapping. A numerical simulation is conducted to study the formation, propagation, and interaction of the shock wave of the composite charge for different initiation modes. It is found that the initiation mode obviously affects the shock-wave waveform and pressure distribution of the composite charge. Additionally, it is found that the area of the overpressure distribution is greatest for internal and external simultaneous initiation, and the peak pressure of the shock wave exponentially decays, fitting the calculation formula of the peak overpressure attenuation under different initiation modes, which is obtained and verified by experiment. The difference between numerical and experimental results is less than 10%, and the peak overpressure of both internal and external initiation is 56.12% higher than that of central single-point initiation.     

Study of nano-nitramine explosives: preparation,sensitivity and application

Nano-nitramine explosives (RDX, HMX, CL-20) are produced on a bi-directional grinding mill. The scanning electron microscope (SEM) observations show that the prepared particles are semi-spherical, and the narrow size distributions are characterized using the laser particle size analyzer. Compared with the micron-sized samples, the nano-products show obvious decrease in friction and impact sensitivities. In the case of shock sensitivities, nano-products have lower values by 59.9% (RDX), 56.4% (HMX), and 58.1% (CL-20), respectively. When nano-RDX and nano-HMX are used in plastic bonded explosives (PBX) as alternative materials of micron-sized particles, their shock sensitivities are significantly decreased by 24.5% (RDX) and 22.9% (HMX), and their detonation velocities are increased by about 1.7%. Therefore, it is expected to promote the application of nano-nitramine explosives in PBXs and composite modified double-based propellants (CMDBs) so that some of their properties would be improved.     

Reaction degree of composition B explosive with multi-layered compound structure protection subjected to detonation loading

The explosive reaction degree and protection from explosions are concerns in the military field.In this work,the reaction degree of the composition B explosive was investigated experimentally.Multi-layered compound structures were used as barriers to weaken the blast loads.A comprehensive experiment using a high-speed camera and image processing techniques,side witness plates,and bottom witness plates was presented.Using the experimental fragment velocities,fragment piercing patterns,and damage characteristics,the reaction degree of the explosive impeded by different multi-layered com-pound structures could be precisely differentiated.Reaction parameters of the explosive obstructed by compound structures were obtained by theoretical analysis and numerical simulations.Unlike the common method in which the explosive reaction degree is only distinguished based on the initial pressure amplitude transmitted into the explosive,a following shock wave reflected from the side steel casing was also considered.Different detonation growth paths in the explosive formed.Therefore,all these shock wave propagation characteristics must be considered to analyze the explosive response impeded by compound structures.     

水下爆炸中自由场压力和船体壁压的测量与分析

对水下爆炸中自由场压力的水面截断效应及冲击裁荷与船体相互作用的船体壁压进行了分析,得出了自由场压力的水面截断效应及早期的船体壁压计算近似公式.测量结果表明,球形装药中心起爆后形成的冲击波一般不是一条光滑曲线,而是会有多个振荡峰;当自由场压力测点离水面较近时,测量的自由场压力会出现明显的水面截断现象;船板在水中爆炸冲击渡的作用下产生的运动和变形对水中压力场有很大影响,舰体壁压反射系数与冲击波的入射角度有关.     

Numerical study on the case effect of a bomb air explosion

When considering the bomb explosion damage effect, the air shock wave and high-speed fragments of the bomb case are two major threats. In experiments, the air shock wave was studied by the bare ex-plosives superseding the real cased bomb; in contrast, the bomb case influence was ignored to reduce risk. The air explosion simulations of the MK84 warhead with and without the case were conducted. The numerical simulation results showed that the bomb case significantly influenced the shock wave generated by the bomb: the spatial distribution of shock wave in the near field changed, and the peak value of shock wave was reduced. Breakage of the case and kinetic energy of the fragmentation consumed 3 and 38% of the explosion energy, respectively. The increasing factors of the peak over-pressure induced by the bare explosive on the ground and in the air were 1.43-3.04 and 1.37-1.57, respectively. Four typical stages of case breakage were defined. The mass distribution of the fragments follows the Mott distribution. The initial velocity distribution of the fragments agreed well with the Gurney equation.     

Shock initiation performance of NTO-based polymer bonded explosive

3-nitro-1,2,4-tri-azol-5-one (NTO) is a high energy insensitive explosive. To study the shock initiation process of NTO-based polymer bonded explosive JEOL-1 (32%octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX), 32% NTO, 28% Al and 8% binder system), the cylinder test, the gap experiments and numerical simulation were carried out. Firstly, we got the detonation velocity (7746 m/s) and the parameters of Jones-Wilkins-Lee (JWL) equation of state (EOS) for detonation product by cylinder test and numerical simulation. Secondly, the Hugoniot curve of unreacted explosive for JEOL-1 was obtained calculating the data of pressure and time at different Lagrangian positions. Then the JWL EOS of unreacted explosive was obtained by utilizing the Hugoniot curve as the reference curve. Finally, we got the pressure growth history of JEOL-1 under shock wave stimulation and the parameters of the ignition and growth reaction rate equation were obtained by the pressure-time curves measured by the shock-initiation gap experiment and numerical simulation. The determined trinomial ignition and growth model (IG model) parameters can be applied to subsequently simulation analysis and design of insensitive ammunition with NTO-based polymer bonded explosive.     

Enhancing the explosive characteristics of a Semtex explosive by involving admixtures of BCHMX and HMX

A well-known ternary plastic explosive, Czech Semtex 1H, contains a mixture of PETN and RDX softened by SBR. In this work, BCHMX was used to replace PETN in Semtex 1H to form Sem-BC+RDX. In addition, another mixture based on BCHMX and HMX as energetic fillers bonded by the polymeric matrix of Semtex 1H (Sem-BC+HMX) was studied. The particle size distribution of each individual explosive was determined to obtain the optimum mixing conditions. Friction and impact sensitivities were determined. The velocity of detonation was reported practically and the detonation properties were calculated by EXPLO5 code. The explosive strength of each sample was measured by the ballistic mortar test. The conclusion confirms that the velocity of detonation of Sem-BC+HMX was the highest in comparison with the prepared samples. Sem-BC+RDX has the least impact and frictions sensitivities. Sem-BC+RDX has higher detonation velocity, detonation properties and explosive strength than Semtex 1H. Addition of BCHMX in Semtex 1H as a replacement for PETN is the candidate to produce a high performance advanced Czech plastic explosive.     

A quasi-isentropic model of a cylinder driven by aluminized explosives based on characteristic line analysis

A quasi-isentropic study on the process of driving a cylinder with aluminized explosives was carried out to examine the influence of the aluminum (Al) reaction rate on cylinder expansion and the physical parameters of the detonation products. Based on the proposed quasi-isentropic hypothesis and relevant isentropic theories, the characteristic lines of aluminized explosives driving a cylinder were analyzed, and a quasi-isentropic model was established. This model includes the variation of the cylinder wall velocity and the physical parameters of the detonation products with the Al reaction degree. Using previously reported experimental results, the quasi-isentropic model was verified to be applicative and accurate. This model was used to calculate the physical parameters for cylinder experiments with aluminized cyclotrimethylenetrinitramine explosives with 15.0 % and 30.0 % Al content. The results show that this quasi-isentropic model can be used not only to calculate the cylinder expansion rule or Al reaction degree, but also to calculate the physical parameters of the detonation products in the process of cylinder expansion. For explosives with 15.0 % and 30.0 % Al, 24.3 % and 18.5 % of the Al was found to have reacted at 33.9 μs and 34.0 μs, respectively. The difference in Al content results in different reaction intensity, occurrence time, and duration of two forms of reaction (diffusion and kinetic) between the Al powder and the detonation products; the post-detonation burning reaction between the Al powder and the detonation products prolongs the positive pressure action time, resulting in a continuous rise in temperature after detonation.