Effect of energy content of the nitraminic plastic bonded explosives on their performance and sensitivity characteristics

Information about the forty nine nitraminic plastic bonded explosives (PBXs) and different nitramines were collected. Fillers of these PBXs are nitramines 1,3,5-trinitro-1,3,5-triazinane (RDX) and β-1,3,5,7-tetranitro-1,3,5-tetrazocane (β-HMX), cis-1,3,4,6-tetranitro-octahydroimidazo-[4,5-d]imidazole (bicyclo-HMX, BCHMX) and ε-2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (ε-HNIW, CL-20) which are bonded by polyfluoro-elastomers, polydimethyl-siloxane, poly-glycidyl azide, polyisobutylene, polystyrene-butadiene, poly-acrylonitrile-butadiene and hydroxyl-terminated polybutadiene in addition to a melt cast compositions based on 2,4,6-trinitrotoluene. For thirty two of these PBXs the relationships are specified and analyzed between heats of their combustion and relative explosive strengths; by means of these relationships it might be possible to estimate, which groupings in the macromolecule of binder could be liable to their primary fission in the PBXs initiation. Similarly, for forty two of these explosives, the relationships are described and analyzed between their enthalpies of formation and impact sensitivities; here is especially attention paid to PBXs filled by BCHMX. Specific rate constants from Vacuum Stability Test (VST) of four nitramines and twenty PBXs are introduced into relationships with their enthalpies of formation. Regarding to all the mentioned cases, increasing of energy content of the studied explosives leads to increase of the relative explosive strength or initiation reactivity, respectively. Exception with the opposite trend, the outputs of VST are for BCHMX, where in PBXs are matrices with the esteric plasticizers or the energetic poly-glycidyl azide. Admixture of RDX or HMX, respectively, into the BCHX PBXs gives ternary PBXs whose thermal stability, in the sense of applied VST, is higher comparing to the original binary explosives.     

Preparation of reduced sensitivity co-crystals of cyclic nitramines using spray flash evaporation

The present day weapon technology demands novel energetic materials that exhibit simultaneous high explosive yield and reduced sensitivity. This article demonstrates application of spray evaporation to prepare reduced sensitive co-crystals of high performance nitramine explosives like HMX and CL-20 with a relatively less insensitive explosive 1,1-diamino-2,2-dinitroethylene or FOX-7. Stronger intermolecular hydrogen bonding in FOX-7 is responsible for limited solubility in most of organic solvents. Large solubility differences of FOX-7 with HMX and CL-20 restricts it's co-crystallization through classical methods that yields thermodynamically favorable product. Spray flash evaporation, a kinetic crystallization method, has been therefore adopted and could successfully produce CL-20/FOX-7 (2:1) and HMX/FOX-7 (4:1) co-crystals. The fine powdered materials obtained were characterized by SEM, powder XRD, Raman spectroscopy, DSC-TGA etc. Multipoint Raman spectra showed consistent occurrence of spectral features indicating stoichiometric co-existence of ingredients in the crystal lattices. DSC analysis showed absence of all thermally assisted solid-solid phase transformation in the co-crystals as they were observed in pristine materials. The thermal stability calculated in terms of activation barrier for decomposition, revealed the CL-20/FOX-7 co-crystal to be intermediately stable on comparison to their constituents while, the HMX/FOX-7 co-crystal is more stable. Compared to pure HMX and CL-20, both the co-crystals have shown higher insensitivity to impact force, suggesting them to be suitable for future generation insensitive munitions.     

Enhancing the explosive characteristics of a Semtex explosive by involving admixtures of BCHMX and HMX

A well-known ternary plastic explosive, Czech Semtex 1H, contains a mixture of PETN and RDX softened by SBR. In this work, BCHMX was used to replace PETN in Semtex 1H to form Sem-BC+RDX. In addition, another mixture based on BCHMX and HMX as energetic fillers bonded by the polymeric matrix of Semtex 1H (Sem-BC+HMX) was studied. The particle size distribution of each individual explosive was determined to obtain the optimum mixing conditions. Friction and impact sensitivities were determined. The velocity of detonation was reported practically and the detonation properties were calculated by EXPLO5 code. The explosive strength of each sample was measured by the ballistic mortar test. The conclusion confirms that the velocity of detonation of Sem-BC+HMX was the highest in comparison with the prepared samples. Sem-BC+RDX has the least impact and frictions sensitivities. Sem-BC+RDX has higher detonation velocity, detonation properties and explosive strength than Semtex 1H. Addition of BCHMX in Semtex 1H as a replacement for PETN is the candidate to produce a high performance advanced Czech plastic explosive.     

Investigation on energy output structure of explosives near-ground explosion

In order to give the energy output structure of typical explosives near-ground explosion in real ground conditions, the free-field shockwave, ground reflection shockwave and Mach wave overpressure time history of composition B explosive, RDX explosive and aluminized explosive were measured by air pressure sensors and ground pressure sensors. The shape of the free-field shock wave, ground reflection shock wave, and Mach wave and explosion flame were captured by high-speed camera. The experimental results show that, at the same horizontal distance from the initiation point, the peak overpressure of explosive shock wave of composition B explosive, both in the air and on the ground, is less than that of RDX and aluminized explosives. At a distance of 3.0 m from the initiation point, the peak overpressure of aluminized explosives is slightly less than that of RDX explosives. Owing to the exothermic effect of aluminum powder, the pressure drop of aluminized explosives is slower than that of RDX explosives. At 5.0 m from the initiation point, the peak overpressure of aluminized explosives is larger than that of RDX explosives. At the same position from the initiation point, among the three kinds of explosives, the impulse of aluminized explosives is the maximum and the impulse of composition B explosives is the minimum. With the increase of the horizontal distance from the initiation point, the height of Mach triple-points (Mach steam) of the three explosives increases gradually. At the same horizontal distance from the initiation point, there is poorly difference in the height of Mach triple-points between aluminized explosive and RDX explosive, and the height of Mach triple-points of composition B explosive is much smaller than that of other two explosives. The maximum diameter and duration of the fireball formed by aluminized explosives are the largest, followed by composition B explosive, and the maximum diameter and duration of the fireball formed by RDX explosive are the smallest.     

Effect of Drying on Particle Size and Sensitivities of Nano hexahydro-1,3,5-trinitro-1,3,5-triazine

Nano hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) was prepared using a bi-directional rotation mill and dried under different conditions (liquid, temperature and drying). It shows that the samples cake seriously and the particles grow up obviously by ordinary drying in different liquids at 70 °C, which occurs again after vacuum drying. With the increase of temperature, the degrees of caking and aggregation are enhanced. Well dispersed sample maintaining constant particle size is extracted by supercritical drying, especially freeze drying. Furthermore, the mechanical sensitivities of I-RDX, O-RDX and F-RDX, of which the average sizes are 88.03 μm, 15.32 μm and 0.16 μm, respectively, are evaluated. Compared with I-RDX, the friction, impact and shock sensitivities of O-RDX are slightly lower. However, the friction, impact and shock sensitivities of F-RDX are reduced by 30%, 99.0% and 59.9%, respectively.     

Formation and characterization of core-shell CL-20/TNT composite prepared by spray-drying technique

The core-shell 2,4,6,8,10,12-Hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane/2,4,6-Trinitrotoluene (CL-20/TNT) composite was prepared by spray-drying method in which sensitive high energy explosive (CL-20) was coated with insensitive explosive (TNT). The structure and properties of different formulations of CL-20/TNT composite and CL-20/TNT mixture were characterized by scanning electron microscopy (SEM), Transmission electron microscopy (TEM), Laser particle size analyzer, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), differential scanning calorimetry (DSC), impact sensitivity test and detonation performance. The results of SEM, TEM, XPS and XRD show that ϵ-CL-20 particles are coated by TNT. When the ratio of CL-20/TNT is 75/25, core-shell structure is well formed, and thickness of the shell is about 20–30 nm. And the analysis of heat and impact show that with the increase of TNT content, the TNT coating on the core-shell composite material can not only catalyze the thermal decomposition of core material (CL-20), but also greatly reduce the impact sensitivity. Compared with the CL-20/TNT mixture (75/25) at the same ratio, the characteristic drop height of core-shell CL-20/TNT composite (75/25) increased by 47.6% and the TNT coating can accelerate the nuclear decomposition in the CL-20/TNT composites. Therefore, the preparation of the core-shell composites can be regarded as a unique means, by which the composites are characterized by controllable decomposition rate, high energy and excellent mechanical sensitivity and could be applied to propellants and other fields.     

Direct ink writing of 3D-Honeycombed CL-20 structures with low critical size

3D-Honeycombed CL-20 structures with low critical size of detonation have been fabricated successfully for intelligent weapon systems using a micro-flow direct ink writing (DIW) technology. The CL-20-based explosive ink for DIW technology was prepared by a two-component adhesive system with waterborne polyurethane (WPU) and ethyl cellulose (EC). Not only the preparation of the explosive ink but also the principle of DIW process have been investigated systematically. The explosive ink displayed strong shear-thinning behavior that permitted layer-by-layer deposition from a fine nozzle onto a substrate to produce complex shapes. The EC content was varied to alter the pore structure distribution and rheological behavior of ink samples after curing. The deposited explosive composite materials are of a honeycombed structure with high porosity, and the pore size distribution increases with the increase of EC content. No phase change was observed during the preparation process. Both WPU and EC show good compatibility with CL-20 particles. Apparently high activation energy was realized in the CL-20-based composite ink compared with that of the refined CL-20 due to the presence of non-energetic but stable WPU. The detonation performance of the composite materials can be precisely controlled by an adjustment in the content of binders. The 3D honeycombed CL-20 structures, which are fabricated by DIW technology, have a very small critical detonation size of less than 69 μm, as demonstrated by wedge shaped charge test. The ink can be used to create 3D structures with complex geometries not possible with traditional manufacturing techniques, which presents a bright future for the development of intelligent weapon systems.     

Preparation and characterization of HMX/EVA/hBNNSs micro-composites with improved thermal stability and reduced sensitivity

Hexagonal boron nitride nanosheets(HBNNSs)have huge potential in the field of coating materials owing to their remarkable chemical stability,mechanical strength and thermal conductivity.Thin-layer hBNNSs were obtained by a liquid-phase exfoliation of h-BN powders and incorporated into EVA coatings for improving the safety performance of 1,3,5,7-tetranitro-1,3,5,7-tetrazocane(HMX).HBNNSs and ethylene-vinyl acetate copolymer(EVA)were introduced to HMX by a solvent-slurry process.For com-parison,the HMX/EVA and HMX/EVA/graphene(HMX/EVA/G)composites were also prepared by a similar process.The morphology,crystal form,surface element distribution,thermal decomposition property and impact sensitivity of HMX/EVA/hBNNSs composites were contrastively investigated.Results showed that as prepared HMX/EVA/hBNNSs composites were well coated with hBNNSs and EVA,and exhibited better thermal stability and lower impact sensitivity than that of HMX/EVA and HMX/EVA/G composites,suggesting superior performance of desensitization of hBNNSs in explosives.     

Preparation and property of CL-20/BAMO-THF energetic nanocomposites

A sol-gel freezing-drying method was utilized to prepare energetic nanocomposites based on 2, 4, 6, 8, 10, 12-hexanitro-2, 4, 6, 8, 10, 12-hexaazaisowurtzitane (CL-20) with 3, 3-Bis (azidomethyl) oxetane-tetrahydrofuran copolymer (BAMO-THF) as energetic gel matrix. Scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman, Fourier-transform infrared spectroscopy (FT-IR) and differential thermal analyser (DTA) were utilized to characterize the structure and property of the resultant energetic nanocomposites. Compared with raw CL-20, the average particle sizes of CL-20 in CL-20/BAMO-THF energetic nanocomposites were decreased to nano scale and the morphologies of CL-20 were also changed from prismatic to spherical. FT-IR detection revealed that CL-20 particles were recrystallized in BAMO-THF gel matrix during the freezing-drying process. The thermal decomposition behaviors of the energetic nanocomposites were investigated as well. The thermolysis process of CL-20/BAMO-THF nanocomposites was enhanced and the activation energy was lower compared with that of raw CL-20, indicating that CL-20/BAMO-THF nanocomposites showed high thermolysis activity. The impact sensitivity tests indicated that CL-20/BAMO-THF energetic nanocomposites presented low sensitivity performance.     

爆轰波在可压缩金属板面上斜反射初始参数的计算

本文计算了爆轰波在可压缩金属板面上斜反射时的初始参数。计算中选用的五种炸药是TNT(p_0为1.64g/cm~3,1.45g/cm~3)、RDX(p_0为1.59g/cm~3,1.76g/cm~3,1.80g/cm~3)、RDX/TNT(77/23)(p_0为1.75g/cm~3)、Pentolite(p_0为1.65g/cm~3,1.68g/cm~3)和B 炸药(p_0为1.71g/cm~3);三种介质是铁、铜和铝。     

Nitro-tetrazole based high performing explosives: Recent overview of synthesis and energetic properties

Heterocyclic skeleton (Azoles) and different energetic groups containing high performing explosives are highly emerged in recent years to meet the challenging requirements of energetic materials in both military and civilian applications with improved performance. For this purpose tetrazole (Azole) is identified as an attractive heterocyclic backbone with energetic functional groups nitro (-NO₂), nitrato (-ONO₂), nitrimino (-NNO₂), and nitramino (–NH–NO₂) to replace the traditionally used high performing explosives. The tetrazole based compounds having these energetic functional groups demonstrated advanced energetic performance (detonation velocity and pressure), densities, and heat of formation (HOF) and became a potential replacement of traditional energetic compounds such as RDX. This review presents a summary of the recently reported nitro-tetrazole energetic compounds containing poly-nitro, di/mono-nitro, nitrato/nitramino/nitrimino, bridged/bis/di tetrazole and nitro functional groups, describing their preparation methods, advance energetic properties, and further applications as high-performing explosives, especially those reported in the last decade. This review aims to provide a fresh concept for designing nitro-tetrazole based high performing explosives together with major challenges and perspectives.     

Effects of nano-sized aluminum on detonation characteristics and metal acceleration for RDX-based aluminized explosive

Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the param-eters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0％to 15％,every 5％increase of aluminum resulted in about a 1.3％decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14％and 8％higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 μs throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12％and 2.9 μs higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80％of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.     

Insensitive energetic microspheres DAAF/RDX fabricated by facile molecular self-assembly

Insensitive energetic materials are promising in the defense weapons field. However, energetic materials still suffer from great challenges and the concern about their safety limits their utilization. In this work, insensitive energetic explosive 3,3′-diamino-4,4′-azoxyfurazan/hexahydro-1,3,5-trinitro-1,3,5-triazine (DAAF/RDX) microspheres were fabricated by self-assembly method. Rod-like DAAF/RDX was prepared by mechanical ball milling for comparison. DAAF/RDX composites with different mass ratios (90:10, 80:20, and 70:30) were obtained. The morphologies and structures of as-obtained DAAF/RDX composites were characterized by scanning electron microscopy (SEM), powder x-ray diffraction (PXRD) and fourier transform infrared spectroscopy (FT-IR). The results showed that DAAF/RDX microspheres exhibited regular shaped microspheres with sizes from 0.5 to 1.2 μm. There was no crystal transition during the modification process. The thermal properties of as-obtained materials were then evaluated by differential scanning calorimetry (DSC) and materials studio software. DAAF/RDX microspheres showed an advanced decomposition peak temperature compared with rod-like DAAF/RDX. The binding energy and peak temperature values at zero β_i (T_P0) of DAAF/RDX (90:10) increased by 36.77 kJ/mol, 1.6 °C, and 58.11 kJ/mol, 12.3 °C compared to DAAF/RDX (80:20) and DAAF/RDX (70:30), indicating the better thermal stability of DAAF/RDX (90:10). The characteristic drop height (H₅₀) of DAAF/RDX (higher than 100 cm) composites was higher than that of raw RDX (25 cm), suggesting significant improvements in mechanical safety. The preparation of DAAF/RDX microspheres is promising for the desensitization of RDX and useful for the formation of other materials and future wide applications.     

Hyperspectral imaging and remote trace detection of cis-1,3,4,6-tetranitrooctahydroimidazo-[4,5 d] imidazole (BCHMX) compared with traditional explosives using laser induced fluorescence

cis-1,3,4,6-Tetranitrooctahydroimidazo-[4,5 d] imidazole (BCHMX) is an advanced energetic compound that expected to spread worldwide in the near future. Since, no approved remote detection methods were reported in current literature for this material, we performed hyper-spectral imaging and laser induced fluorescence (LIF) to a BCHMX sample under low laser fluence for determining the optimum laser wavelength used in any future BCHMX-LIF based remote detection systems. For this purpose, an experimental setup consisted of a sun spectrum lamp and hyper-spectral camera was built to illuminate and image white powder samples of BCHMX in comparison with the traditional explosives, HMX (1,3,5,7-tetranitro-1,3,5,7-tetraazacyclooctane), RDX (1,3,5-trinitro-1,3,5-triazacyclohexane), PETN (2,2-Bis[(nitroxy)methyl]propane-1,3-diyldinitrate). The imaging reveals strong BCHMX sample absorption contrast among other samples at wavelength ranging from 400 to 410 nm. When light source was replaced by a 405 nm laser diode illuminator, a strong BCHMX sample LIF at the spectral range from 425 to 700 nm was observed under low laser fluence condition of 0.1 mJ/cm². Finally, we demonstrated successfully the ability of the 405 nm LIF and the hyperspectral imaging technique to detect finger print traces of BCHMX on white cellulose fabric from a distance of 15 m and a detection limit of 1 μg/cm².     

Sandwich structure for enhancing the interface reaction of hexanitrohexaazaisowurtzitane and nanoporous carbon scaffolds film to improve the thermal decomposition performance

Improving the thermal decomposition performance of hexanitrohexaazaisowurtzitane (CL-20) by appropriate methods is helpful to promote the combustion performance of CL-20-based solid propellants. In this study, we synthesized a sandwich structure of CL-20 and nanoporous carbon scaffolds film (NCS) and emphatically studied the thermal decomposition performance of the composite structure. Thermogravimetric analysis and differential scanning calorimetry were used to measure the thermal decomposition process of the composite structure. The kinetic parameters of thermal decomposition were calculated by the thermal dynamic analysis software AKTS. These results showed that the thermal decomposition performance of the sandwich structure of CL-20 and NCS was better than CL-20. Among the tested samples, NCS with a pore size of 15 nm had the best catalytic activity for the thermal decomposition of CL-20. Moreover, the thermal decomposition curve of the composite structure at the heating rate of 1 K/min was deconvoluted by mathematical method to study the thermal decomposition process. And a possible catalytic mechanism was proposed. The excellent thermal decomposition performance is due to the sandwich structure enhances the interface reaction of CL-20 and NCS. This work may promote the extensive use of CL-20 in the field of solid rocket propellant.     

A melt-cast Duan-Zhang-Kim mesoscopic reaction rate model and experiment for shock initiation of melt-cast explosives

A melt-cast Duan-Zhang-Kim (DZK) mesoscopic reaction rate model is developed for the shock initiation of melt-cast explosives based on the pore collapse hot-spot ignition mechanism. A series of shock initiation experiments was performed for the Comp B melt-cast explosive to estimate effects of the loading pressure and the particle size of granular explosive component, and the mesoscopic model is validated against the experimental data. Further numerical simulations indicate that the initial density and formula proportion greatly affect the hot-spot ignition of melt-cast explosives.     

Nanothermite colloids: A new prospective for enhanced performance

Nanothermites (metal oxide/metal) can offer tremendously exothermic self sustained reactions. CuO is one of the most effective oxidizers for naonothermite applications. This study reports on two prospectives for the manufacture of CuO nanoparticles. Colloidal CuO particles of 15 nm particle size were developed using hydrothermal synthesis technique. Multiwalled carbon nanotubes (MWCNTs) with surface are 700 m²/g was employed as a substrate for synthesis of CuO-coated MWCNTs using electroless plating. On the other hand, aluminium particles with combustion heat of 32000 J/g is of interest as high energy density material. The impact of stoichiometric nanothermite particles (CuO/Al & Cuo-coated MWCNTs/Al) on shock wave strength of Al/TNT nanocomposite was evaluated using ballistic mortar test. While CuO-coated MWCNTs decreased the shock wave strength by 15%; colloidal CuO enhanced the shock wave strength by 30%. The superior performance of colloidal CuO particles was correlated to their steric stabilization with employed organic solvent. This is the first time ever to report on fabrication, isolation, and integration of stablilized colloidal nanothermite particles into energetic matrix where intimate mixing between oxidizer and metal fuel could be achieved.     

The Early Responses of Air-backed plate subjected to underwater explosion with aluminized explosives

This work aims to research the effects on the early responses of the air-backed plate subjected to the loading generated by the underwater explosion with aluminized explosives. The loading characteristics of underwater explosion for ideal explosive (TNT), aluminized explosives (RS211 and RBUL) are obtained experimentally. The tested aluminized explosives have different energy output compared with TNT. Based on the Taylor plate theory, the early responses of the air-backed steel plate affected by the measured loading is analyzed. The analytical results indicate that the pressure curve of the shock wave within 1 time decay constant is the main factor affecting the kick-off velocity of the plate when cavitation occurring. The velocity responses of the plate produced by the loading of RS211 and RBUL are obviously different with that of an equivalent TNT charge, which also indicates validity and suitability should be noticed in the case of substituting TNT for aluminized explosives. Moreover, the uncertainties in the responses of the plate produced by RS211 and RBUL are much larger than TNT.     

Shock initiation performance of NTO-based polymer bonded explosive

3-nitro-1,2,4-tri-azol-5-one (NTO) is a high energy insensitive explosive. To study the shock initiation process of NTO-based polymer bonded explosive JEOL-1 (32%octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX), 32% NTO, 28% Al and 8% binder system), the cylinder test, the gap experiments and numerical simulation were carried out. Firstly, we got the detonation velocity (7746 m/s) and the parameters of Jones-Wilkins-Lee (JWL) equation of state (EOS) for detonation product by cylinder test and numerical simulation. Secondly, the Hugoniot curve of unreacted explosive for JEOL-1 was obtained calculating the data of pressure and time at different Lagrangian positions. Then the JWL EOS of unreacted explosive was obtained by utilizing the Hugoniot curve as the reference curve. Finally, we got the pressure growth history of JEOL-1 under shock wave stimulation and the parameters of the ignition and growth reaction rate equation were obtained by the pressure-time curves measured by the shock-initiation gap experiment and numerical simulation. The determined trinomial ignition and growth model (IG model) parameters can be applied to subsequently simulation analysis and design of insensitive ammunition with NTO-based polymer bonded explosive.     

Burning characteristics of high density foamed GAP/CL-20 propellants

The monolithic foamed propellants with high densities were prepared by casting and two-step foaming processes. Glycidyl azide polymer (GAP) and isocyanate were used as the binder system and 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (HNIW, CL-20) was employed as the energetic component. The newly designed formulation containing 60 % CL-20 produced a force constant of 1077 J/g and low flame temperature of 2817 K. Two foamed propellants with densities of 1.32 g/cm³ and 1.53 g/cm³ were fabricated by a confined foaming process and examined by closed bomb tests. The results revealed that porosity significantly affects burning performance. A size effect on combustion behaviors was observed for the foamed propellant with 5.56 % porosity, and a double-hump progressive dynamic vivacity curve was obtained. At last, the 30 mm gun test was carried out to demonstrate the interior ballistic performance, and the muzzle velocity increased by 120 m/s at the same maximum chamber pressure when monolithic propellant was added in the charge.