SAR微动目标的稀疏贝叶斯成像方法

SAR微动信息能够反映出目标的属性信息,其微动图像可作为雷达目标识别的一种重要手段。基于SAR微动目标回波的稀疏特性,建立了在过完备词典下的稀疏表示模型,提出一种新的稀疏贝叶斯重构方法——方差成分扩张压缩,该方法仅赋予有重要意义的信号元素不同的方差分量,拥有更少的参数。仿真结果表明,方差成分扩张压缩方法能较精确地估计出SAR目标微动参数,同时能够获得低信噪比条件下较好的微动目标像。     

军用装备镁合金表面微弧氧化层SEM微观形貌及耐蚀性分析

利用微弧氧化技术的恒电流方式,在含有Na：SiO,和KF等电解质的溶液中制备了AZ91D镁合金微弧氧化层,通过扫描电镜观察分析及Cu加速盐雾腐蚀试验,研究了电解液中Na：SiO,和KF质量浓度对微弧氧化层结构及耐蚀性的影响。结果表明：在相同反应条件下,微弧氧化层厚度和表面粗糙度随Na：SiO,和KF质量浓度的增加而增加,微弧氧化层的耐蚀性取决于其表面粗糙度和厚度,粗糙度小、具有一定厚度的致密微弧氧化层耐蚀性好。     

导航级微型核磁共振陀螺仪技术综述

导航级微型核磁共振陀螺仪是美国国防高级研究项目局为了克服全球定位系统(GPS)在受到强干扰或GPS星座受损而失效的潜在威胁而开发的,其技术特点是通过微制造技术将所有必须的组件封装成为一个小型、低功耗、片式、高精度的惯性测量组合。从核磁共振原理、核磁共振陀螺仪原理、发展现状以及关键技术等方面对核磁共振陀螺仪进行了介绍。     

电场作用微燃烧器的液体乙醇层流扩散燃烧

采用实验和数值模拟方法对电场作用下微燃烧器的液体乙醇层流扩散燃烧进行研究。研究结果表明,数值模拟高温区与实验拍摄火焰结构外形相似,前者的结构尺寸均高于后者;H/d与R e基本上呈线性增加关系,W/d先随R e线性增加,后变化幅度较小;H/d与电场强度E之间存在波浪曲线关系,波浪整体呈上升趋势,W/d整体上随电场强度E也呈上升趋势;火焰高度和宽度无量纲的数值模拟值与实验计算值吻合良好。     

Parametric inference for component distributions from lifetimes of systems with dependent components

In system reliability analysis, for an n ‐component system, the estimation of the performance of the components in the system is not straightforward in practice, especially when the components are dependent. Here, by assuming the n components in the system to be identically distributed with a common distribution belonging to a scale‐family and the dependence structure between the components being known, we discuss the estimation of the lifetime distributions of the components in the system based on the lifetimes of systems with the same structure. We develop a general framework for inference on the scale parameter of the component lifetime distribution. Specifically, the method of moments estimator (MME) and the maximum likelihood estimator (MLE) are derived for the scale parameter, and the conditions for the existence of the MLE are also discussed. The asymptotic confidence intervals for the scale parameter are also developed based on the MME and the MLE. General simulation procedures for the system lifetime under this model are described. Finally, some examples of two‐ and three‐component systems are presented to illustrate all the inferential procedures developed here. © 2012 Wiley Periodicals, Inc. Naval Research Logistics, 2012     

一种改进的小波域LFM雷达信号参数估计算法

提出了基于重排小波-Radon变换的线性调频信号的参数估计法。该方法先将小波尺度图转为时频分布图,为提高聚集性引入了时频重排,再将重排图进行Radon变换以进行参数估计。仿真结果表明,该方法有效提高了时频分布图的聚集性,节省了后续Radon变换的时间,同时也抑制了噪声干扰,辨识效果明显提高。     

自适应窗口仿射最小二乘匹配方法

为了解决仿射最小二乘匹配方法在未知初始参数条件下无法自适应选择匹配窗口的问题,提出了一种基于局部形状估计的自适应窗口最小二乘匹配方法。利用LOG(Laplacian of Gaussian)算子检测特征点以及特征点所在的尺度;在特征点邻域内根据特征尺度计算局部二阶矩矩阵,用二阶矩矩阵估计特征点局部的形状特征;根据特征点局部的形状自适应选择初始匹配窗口进行仿射最小二乘迭代。实验结果表明,该方法在较大仿射变形下能够准确的选择有效匹配区域,避免因窗口内容差异造成的迭代不收敛问题。     

An empirical bayes estimator for the scale parameter of the two-parameter weibull distribution

An empirical Bayes estimator is given for the scale parameter in the two-parameter Weibull distribution. The scale parameter is assumed to vary randomly throughout a sequence of experiments according to a common, but unknown, prior distribution. The shape parameter is assumed to be known, however, it may be different in each experiment. The estimator is obtained by means of a continuous approximation to the unknown prior density function. Results from Monte Carlo simulation are reported which show that the estimator has smaller mean-squared errors than the usual maximum-likelihood estimator.     

基于核主成分分析的铁谱磨粒特征提取方法研究

针对铁谱分析的磨粒识别过程中存在原始磨粒特征描述指标参数多、非线性突出的问题,提出基于核主成分分析的磨粒特征提取方法,介绍该方法的原理与算法。结合某柴油发动机故障检测与分析系统中铁谱磨粒自动识别的应用实例,并与传统主成份分析方法进行对比分析,结果表明该方法在进行样本非线性特征参数指标综合以及特征维数压缩方面具有可行性和有效性。     

嵌入遗传算法的顺轨干涉SAR海表流场反演新方法

顺轨干涉SAR海表流场探测技术研究对于实现流场探测的全球化、精细化具有重要作用。为了提高海表流场迭代收敛速度和参数反演精度,依据校正系数的参数特点构建适应度函数的约束关系,将校正系数设计问题转化为仿真干涉相位与实测干涉相位差和雷达、平台参数约束条件下的比例因子选择问题,进而设计遗传算法计算校正系数的技术方法,并嵌入海表流场迭代反演算法,从而构建一种反演新方法。星载SAR数据仿真实验结果表明:海表流向反演的均方根误差优于10.0°,海表流速的均方根误差优于0.1 m/s,这符合海表流场反演精度要求。改进的海表流场反演算法可减少2~3次迭代,有效提高了反演效率。研究对于提高顺轨干涉SAR海表流场探测的实效性和准确性具有重要意义。     

Formulation development and characterization of cellulose acetate nitrate based propellants for improved insensitive munitions properties

Cellulose acetate nitrate (CAN) was used as an insensitive energetic binder to improve the insensitive munitions (IM) properties of gun propellants to replace the M1 propellant used in 105 mm artillery charges. CAN contains the energetic nitro groups found in nitrocellulose (NC), but also acetyl functionalities, which lowered the polymer's sensitivity to heat and shock, and therefore improved its IM properties relative to NC. The formulation, development and small-scale characterization testing of several CAN-based propellants were done. The formulations, using insensitive energetic solid fillers and high-nitrogen modifiers in place of nitramine were completed. The small scale characterization testing, such as closed bomb testing, small scale sensitivity, thermal stability, and chemical compatibility were done. The mechanical response of the propellants under high-rate uni-axial compression at, hot, cold, and ambient temperatures were also completed. Critical diameter testing, hot fragment conductive ignition (HFCI) tests were done to evaluate the propellants' responses to thermal and shock stimuli. Utilizing the propellant chemical composition, theoretical predictions of erosivity were completed. All the small scale test results were utilized to down-select the promising CAN based formulations for large scale demonstration testing such as the ballistic performance and fragment impact testing in the 105 mm M67 artillery charge configurations. The test results completed in the small and large scale testing are discussed.     

固体发动机尾部点火性能影响因素分析

采用准一维非定常数值模型,对某小型固体发动机尾部点火瞬态过程进行性能预示;以预示结果为基础,对尾部点火性能主要影响因素进行了参数研究.研究结果可为尾部点火器和喷管堵盖的点火匹配性设计提供有益指导.     

光学表面的分形特点与模拟表征算法

根据光学表面在微观结构呈现出的自相似性,利用尺度无关的分形模型描述了其结构特征;采用结构函数法对抛光表面的分形维数进行计算,分析了粗糙度参数RMS值、误差波长、测量尺度、采样长度和采样点数对分形维数的影响规律。在此基础上,提出了采用一阶自回归分形模型对抛光表面进行模拟的新方法,分析了界定尺度、模型参数对分形特征和分形维数的影响规律。利用分形维数描述光学表面的微观结构具有评价方法简单、在一定范围内与测量尺度无关等优点。     

气液同轴式喷嘴缩进比对雾化细度影响的实验

缩进比是液体火箭发动机气液同轴式喷嘴设计中一个重要参数。本文对缩进比对喷嘴雾化特性的影响进行了实验研究。结果表明;在不同工作参数下不同缩进比的喷嘴,其雾化特性有一定的差别。缩进比对雾化细度的影响不如其对雾化的流强和混合比分布及噪声等的影响明显。在气侧压降较小时,缩进比过大过小都不利于雾化;而在气侧压降较大时,缩进比较大或较小都会对雾化有一定的改善。但当缩进比过大时,气液之间的相互作用会使得液体喷注压降明显地波动。     

微槽平板热管传热性能的实验研究

系统地研究小充液率条件下重力对微槽平板热管传热性能的影响,分析了工作温度、冷却方式等影响因素.发现重力对热管径向液膜的分布影响比较小,而对轴向的影响比较明显,从而使得倾角较大地影响了热管的传热能力.进一步证明了深槽平板热管具有良好的传热性能.     

Study on Modeling and Control Strategy for Electric Drive Motor of Tracked Vehicles

Aimed at the requirements for electric transmission system of a military tracked vehicle, the motor's design indexes were analysed and calculated. A model based on saturate inductance parameter of interior permanent magnet (IPM) synchronous motor was brought forward by using finite element analysis. And its control strategy based on the largest running capability was studied also. The experiment results for a scale model show that the modelling method improves the model's accuracy, and the motor's control strategy is effective.     

小子样条件下基于Normal-Poisson过程的性能可靠性评定

对于高可靠、长寿命产品,基于性能退化数据分析可靠性是一种行之有效的技术途径。结合航空航天产品性能退化的机理与现场试验小子样的特点,建立了基于Normal-Poisson过程的性能退化模型。论文在对产品性能退化建模的基础上,结合Bayes方法给出了退化模型参数的估计算法和可靠性推断的公式,最后结合实例说明了方法的有效性。     

考虑不完全维修的可修串联系统可用度模型

可用度是衡量系统可靠性、维修性水平的一个重要指标.提出一类基于gamma劣化过程的可修串联系统的可用度计算方法.该方法从构成系统部件的状态出发,用gamma过程刻画部件的退化失效规律,同时考虑系统维修效果的不完全性,在此基础上推导出系统可用度的表达式.最后用一个算例验证了研究模型的合理性.     

Optimum step‐stress accelerated life test plans for log‐location‐scale distributions

This article presents new tools and methods for finding optimum step‐stress accelerated life test plans. First, we present an approach to calculate the large‐sample approximate variance of the maximum likelihood estimator of a quantile of the failure time distribution at use conditions from a step‐stress accelerated life test. The approach allows for multistep stress changes and censoring for general log‐location‐scale distributions based on a cumulative exposure model. As an application of this approach, the optimum variance is studied as a function of shape parameter for both Weibull and lognormal distributions. Graphical comparisons among test plans using step‐up, step‐down, and constant‐stress patterns are also presented. The results show that depending on the values of the model parameters and quantile of interest, each of the three test plans can be preferable in terms of optimum variance. © 2008 Wiley Periodicals, Inc. Naval Research Logistics, 2008