煤油超音速燃烧的试验研究

在地面直连式试车台上,研究了煤油碳氢燃料超燃冲压发动机的点火燃烧性能。通过测量模型发动机壁面压力分布,比较了不同工况下的煤油点火燃烧性能。试验结果表明,在当量比为0.27～1.46的大范围内,煤油在超燃冲压模型发动机中能够成功点火,支板和凹腔对煤油在超声速气流中的点火及稳定燃烧有重要作用,少量氢气的喷入对煤油的点火燃烧有良好的促进作用。太厚的支板、过高的当量比、模型发动机第一级燃烧室加入燃料过多会使发动机壅塞,影响隔离段的正常工作,进而影响加热器喷管工作。     

空气/煤油/水燃气发生器点火特性试验研究

燃气发生器是超燃冲压发动机地面试验系统中的关键设备,为提高系统安全性和经济性设计了空气/煤油/水燃气发生器,在富燃状态下进行了一系列点火试验,试验结果表明：该型燃气发生器,实现可靠点火的余氧系数下限为0.51;水的加入使得化学反应速率和火焰传播速度降低,燃气发生器点火和火焰稳定困难,提高余氧系数可以提高点火可靠性。同时水的加入容易引起燃烧不稳定,通过提高余氧系数可消除低频不稳定燃烧。     

空气/煤油/水燃气发生器点火特性试验

燃气发生器是超燃冲压发动机地面试验系统中的关键设备,为提高系统安全性和经济性设计了空气/煤油/水燃气发生器,在富燃状态下进行了一系列点火试验,试验结果表明:该型燃气发生器,实现可靠点火的余氧系数下限为0.51;水的加入使得化学反应速率和火焰传播速度降低,燃气发生器点火和火焰稳定困难,提高余氧系数可以提高点火可靠性。同时,水的加入容易引起燃烧不稳定,通过提高余氧系数来消除低频不稳定燃烧。     

Effects of total pressures and equivalence ratios on kerosene/air rotating detonation engines using a paralleling CE/SE method

In this paper, the kerosene/air rotating detonation engines(RDE) are numerically investigated, and the emphasis is laid on the effects of total pressures and equivalence ratios on the operation characteristics of RDE including the initiation, instabilities, and propulsive performance. A hybrid MPI + OpenMP parallel computing model is applied and it is proved to be able to obtain a more effective parallel performance on high performance computing(HPC) systems. A series of cases with the total pressure of 1 MPa, 1.5 MPa, 2 MPa, and the equivalence ratio of 0.9, 1, 1.4 are simulated. On one hand, the total pressure shows a significant impact on the instabilities of rotating detonation waves. The instability phenomenon is observed in cases with low total pressure (1 MPa) and weakened with the increase of the total pressure. The total pressure has a small impact on the detonation wave velocity and the specific impulse. On the other hand, the equivalence ratio shows a negligible influence on the instabilities, while it affects the ignition process and accounts for the detonation velocity deficit. It is more difficult to initiate rotating detonation waves directly in the lean fuel operation condition. Little difference was observed in the thrust with different equivalence ratios of 0.9, 1, and 1.4. The highest specific impulse was obtained in the lean fuel cases, which is around 2700 s. The findings could provide insights into the understanding of the operation characteristics of kerosene/air RDE.     

Characteristics structure analysis on debris cloud in the hypervelocity impact of disk projectile on thin plate

In this paper, the gauge points setting is introduced in the SPH simulation to analyze the debris cloud structure generated by the hypervelocity impact of disk projectile on thin plate. Compared with the experiments, more detailed information of the debris cloud structure can be classified from the numerical simulation. However, due to the solitary dispersion and overlap display of the particles in the SPH simulation, accurate comparison between numerical and experimental results is difficult to be performed. To track the velocity and spatial distribution of the particles in the debris cloud induced from disk and plate, gauge points are locally set in the single-layer profile in the SPH model. By analyzing the gauge points’ spatial coordinate and velocity, the location and velocity of characteristic points in the debris cloud are determined. The boundary of debris cloud is achieved, as well as the fragments distribution outside the main structure of debris cloud.     

应用地面电磁发射清除空间碎片方法

针对传统化学发射的空间碎片清除技术成本过高、难以实施的问题,提出应用地基电磁发射方式的空间碎片清除新方法。通过地面电磁发射的方式以低成本将射弹运送至空间,并通过释放空间微粒云团控制空间碎片离轨,进而实现对空间碎片的清除。由于取消使用占绝大部分成本的化学推进剂,所提出的应用地基电磁发射的空间碎片清除技术为空间碎片低成本清除提供了有效解决途径。     

Growth model of cavity generated by the projectile impacting liquid-filled tank

The high-speed impact of a projectile on a liquid-filled tank causes the hydraulic ram, in which a cavity is formed. To study the growth characteristics of the cavity, the formation mechanism of the cavity is analyzed. The effect of Reynolds number and Mach number on drag coefficient is considered, the axial and radial growth models of the cavity are established respectively. The relative errors between the cavity length calculated by the axial growth model, the cavity diameter calculated by the radial growth model and Ma L. Y. test results are less than 20%, which verifies the effectiveness of the axial and radial growth models. Finally, numerical simulation is carried out to study the growth characteristics of the cavity caused by the projectile impacting the satellite tank at the velocity of 4000 m/s. The cavity length and diameter calculated by the axial and radial growth models agree well with those obtained by simulation results, indicating that the cavity length and diameter in satellite tank can be accurately calculated by the axial and radial growth models.     

坦克底盘角振动对火炮射击精度影响机理研究

实车试验表明,在行进间射击试验时,当车辆超过一定车速(行进间射击车速)时,射击精度或射击命中率会发生大幅度的下降。针对这个问题,建立了坦克底盘角振动导致的射击偏差的数学模型;并结合实车试验数据,对射击延迟时间内底盘角振动造成的火炮射击偏差进行了全面分析。分析研究表明:在相同的行驶车速条件下,车辆底盘角速度、姿态角变化量随着射击延迟时间的增大而增大;在相同的射击延迟时间内,车辆底盘角速度、姿态角变化量与射角偏差随着行驶车速的增大而增大;其中射角偏差引起的目标距离偏差是弹丸横向速度导致的目标距离偏差的3倍~5倍。因此,随着行驶车速增加而增加的射角偏差增大是行进间射击车速受限的主要原因。     

Dynamic analysis of a guided projectile during engraving process

The reliability of the electronic components inside a guided projectile is highly affected by the launch dynamics of guided projectile. The engraving process plays a crucial role on determining the ballistic performance and projectile stability. This paper analyzes the dynamic response of a guided projectile during the engraving process. By considering the projectile center of gravity moving during the engraving process, a dynamics model is established with the coupling of interior ballistic equations. The results detail the stress situation of a guided projectile band during its engraving process. Meanwhile, the axial dynamic response of projectile in the several milliseconds following the engraving process is also researched. To further explore how the different performance of the engraving band can affect the dynamics of guided projectile, this paper focuses on these two aspects: (a) the effects caused by the different band geometry; and (b) the effects caused by different band materials. The time domain and frequency domain responses show that the dynamics of the projectile are quite sensitive to the engraving band width. A material with a small modulus of elasticity is more stable than one with a high modulus of elasticity.     

坦克射击过程中炮膛内火药气体温度计算

坦克射击后出现炮膛内壁烧蚀及身管温度上升等问题，其首要因素为火药爆炸燃烧所产生的高温气体。应用内弹道零维模型，以空间平均热力学参数描述坦克射击过程中炮膛内弹道状态，采用四阶龙格一库塔法求解内弹道常微分方程组，计算出内弹道时期火药气体的压力、流速和温度等随时间的变化规律。应用指数函数拟合出后效期炮膛内火药气体温度公式，最后得到坦克整个射击过程中炮膛内火药气体温度的变化规律。通过计算结果与试验数据的对比，验证了计算结果的合理性。此计算结果可为坦克炮身管的烧蚀、热状况及红外辐射特性的研究提供理论依据。     

目标角速度测量误差分析

对现有坦克火控系统中目标角速度测量误差进行了分析,提出了几种提高测量精度和射弹命中率的方法.     

爆炸成型弹丸贯穿靶板靶后破片空间分布模型

深空撞击载荷对探测小天体内部物质成分和结构特性具有重要意义,因此,在考虑爆炸成型弹丸(explosively formed projectile, EFP)可变截面的特性和区分靶后破片来源的基础上,建立了EFP贯穿靶板靶后破片空间分布模型。在靶板厚度30 mm至70 mm、EFP着靶速度1 650 m/s至1 860 m/s的条件下,该模型可以定量预测靶后破片云中各个破片的速度、质量、数量与空间位置的关系。结果表明,相对速度总是随相对空间位置的增加而呈线性增加,相对质量、相对数量总是随相对空间位置的增加而呈幂函数增加。     

电磁发射弹丸飞行弹道仿真

针对电磁发射弹丸飞行弹道进行仿真研究，在建立刚体六自由度飞行弹道模型的基础上，采用时频分析和涡流分析方法，建立电磁-动力学耦合模型分析弹丸出膛时由于膛内振动带来的炮口扰动，采用动网格技术建立电磁-气动耦合模型分析弹托分离产生的气动扰动，从而得到了电磁发射弹丸的飞行弹道模型。以得克萨斯大学先进技术研究所设计的IAT-HVP为例，仿真分析了弹丸以1117 m/s初速、0°射角出膛时弹丸出口扰动对弹体速度和气动特性的影响，并得到其飞行200 m的弹道曲线。仿真结果表明，受电磁发射一体化弹丸出口扰动的影响，弹体落点相比理想弹道产生了24%的偏差，其中炮口扰动引起的偏差最大，其次是弹托分离。     

防暴发射器身管长度优化研究

为解决某型防暴发射器身管设计不合理导致有效射程短的问题,以仿真设计的方法,运用Matlab计算软件对其进行了内弹道模拟仿真,获得了不同身管长度下该防暴发射器的膛压和速度曲线,确定了最优身管长度。然后利用ANsYs有限元分析软件,对延长身管后的模型进行了强度校核。仿真结果和实弹数据表明：防暴发射器身管长度设计合理,有效提高了其实际射程和作战效能,研究工作优化了防暴发射器的设计。     

Interface defeat studies of long-rod projectile impacting on ceramic targets

The interface defeat phenomenon always occurs when a long-rod projectile impacting on the ceramic target with certain velocity, i.e., the projectile is forced to flow radially on the surface of ceramic plates for a period of time without significant penetration. Interface defeat has a direct effect upon the ballistic performance of the armor piercing projectile, which is studied numerically and theoretically at present. Firstly, by modeling the projectiles and ceramic targets with the SPH (Smoothed Particle Hydrodynamics) particles and Lagrange finite elements, the systematic numerical simulations on interface defeat are performed with the commercial finite element program AUTODYN. Three different responses, i.e., complete interface defeat, dwell and direct penetration, are reproduced in different types of ceramic targets (bare, buffered, radially confined and oblique). Furthermore, by adopting the validated numerical algorithms, constitutive models and the corresponding material parameters, the influences of projectile (material, diameter, nose shape), constitutive models of ceramic (JH-1 and JH-2 models), buffer and cover plate (thickness, constraints, material), as well as the prestress acted on the target (radial and hydrostatic) on the interface defeat (transition velocity and dwell time) are systematically investigated. Finally, based on the energy conservation approach and taking the strain rate effect of ceramic material into account, a modified model for predicting the upper limit of transition velocity is proposed and validated. The present work and derived conclusions can provide helpful reference for the design and optimization of both the long-rod projectile and ceramic armor.     

Research on 2D Model of Capillary Discharge Plasma

The physical process of capillary discharge in a PE tube utilized in electro-thermal-chemical(ETC)guns was investigated.ETC guns can enhance the ignition and combustion of propellant in order to reduce the ignition delay and increase muzzle velocity of the projectile.A key component in ETC gun is the capillary plasma source.In this paper,a 2D steady state model of discharge was built by using magnetic hydrodynamics method.It took the plasma energy balance,material ablation,mass and momentum conservations in a quasi-neutral plasma region into account.Also,the effect of different compositions and PE concentration distribution were considered.In order to evaluate the validation of this model,the simulation results are compared with former works.     

Analysis on the resistive force in penetration of a rigid projectile

According to the dimensionless formulae of DOP (depth of penetration) of a rigid projectile into different targets, the resistive force which a target exerts on the projectile during the penetration of rigid projectile is theoretically analyzed. In particular, the threshold V_c of impact velocity applicable for the assumption of constant resistive force is formulated through impulse analysis. The various values of V_c corresponding to different pairs of projectile-target are calculated, and the consistency of the relative test data and numerical results is observed.     

基于刚柔耦合的坦克炮发射动力学仿真分析

炮口扰动是影响坦克炮射击精度的重要因素，为研究弹丸出炮口瞬间的炮口扰动规律，基于多体动力学与有限元方法构建了坦克刚柔耦合的全车动力学仿真模型，该模型考虑了身管的柔性特性，对身管进行了模态分析，得到了身管的模态中性文件。通过仿真，对比了后坐部分最大后坐位移与最大后坐速度的试验值与仿真值，对刚柔耦合模型的仿真结果进行了验证。在此基础上，分析了刚性身管和柔性身管对炮口扰动的影响，结果表明：考虑身管柔性特性的刚柔耦合模型能够有效提高坦克炮射击仿真精度。     

Experimental research on the instability propagation characteristics of liquid kerosene rotating detonation wave

In order to study the instability propagation characteristics of the liquid kerosene rotating detonation wave (RDW), a series of experimental tests were carried out on the rotating detonation combustor (RDC) with air-heater. The fuel and oxidizer are room-temperature liquid kerosene and preheated oxygen-enriched air, respectively. The experimental tests keep the equivalence ratio of 0.81 and the oxygen mass fraction of 35% unchanged, and the total mass flow rate is maintained at about 1000 g/s, changing the total temperature of the oxygen-enriched air from 620 K to 860 K. Three different types of instability were observed in the experiments: temporal and spatial instability, mode transition and re-initiation. The interaction between RDW and supply plenum may be the main reason for the fluctuations of detonation wave velocity and pressure peaks with time. Moreover, the inconsistent mixing of fuel and oxidizer at different circumferential positions is related to RDW oscillate spatially. The phenomenon of single-double-single wave transition is analyzed. During the transition, the initial RDW weakens until disappears, and the compression wave strengthens until it becomes a new RDW and propagates steadily. The increased deflagration between the detonation products and the fresh gas layer caused by excessively high temperature is one of the reasons for the RDC quenching and re-initiation.