高速水下射弹空泡形态及其CFD分析

射弹在水下空泡形态高速运动,实验研究存在很多限制。本文应用两种方法对高速水下射弹的空泡形态及阻力性质进行了研究,一是应用CFD仿真模拟软件,二是应用基于空泡截面独立扩张原理所建立的公式。研究表明：仿真计算结果与公式计算结果吻合很好;随着空化数的减小,空泡的相对长度、相对直径和长细比都在增大;在小空化数下,空泡前部形态基本不变,阻力系数主要为压差阻力系数,其值基本不变。研究结果为射弹的外形设计提供参考。     

Experiment and Calculation for Expansion Process of Ablation Plasma Jets in Liquid

The expansion process of ablation plasma jet in liquid was experimentally investigated by using high speed digital camera. The sequential pictures show that, in the initial stage of the jet, the Taylor cavity expands in the axial and radial directions simultaneously, and then, is subjected to the constraint of chamber wall, in axial direction mainly. The maximum axial speed of the cavity's head ranges from 240m/s to 280m/s. Some strong heat conduction and mass transmission effects can be found in the surface of Taylor cavity, where the plasma cools down and condenses as solid particles while the liquid vaporizes as gas. Compared the expansion processes of the cavities among the different discharge energies and the nozzle diameters, it can be seen that the expansion speed of the cavity is directly proportional to the discharge energy and inversely to the nozzle diameter, and the effect of the discharge energy is stronger than that of the nozzle diameter. A set of equations describing the expansion process of ablation plasma jet was derived under the assumption of momentum conservation. The calculated results by use of the equations coincide with the experimented results better.     

动态旋流器湍流流场的模拟研究

采用雷诺应力模型对动态旋流器湍流流场进行模拟.模拟结果与文献实验数据基本吻合,证明该模型的正确性.其中,轴向和切向速度的模拟结果和实际结果非常接近;径向速度的模拟将有助于旋流器结构及性能的分析.所建立的模型和所使用的计算方法为深入探讨动态水力旋流器的流场特性、分离机理及结构优化设计提供了一条有效的途径.     

基于内角流动的板式表面张力贮箱内推进剂流动过程研究

分析了在微重力环境下,板式表面张力贮箱内推进剂的流动和定位过程.利用VOF方法对贮箱内推进剂的重定位过程进行了仿真计算,验证了贮箱及PMD的推进剂管理性能.用数学方法分析了液体在导流板的内角流动,用解析计算的方法求出流动过程中液面的长度,并和仿真计算结果进行了对比.因为实际的贮箱模型比较复杂,仿真计算结果和理论计算结果存在一定的误差,但其流动趋势保持一致.本文的工作能够为内角流动的研究提供有益的参考.     

基于刚柔耦合的坦克炮发射动力学仿真分析

炮口扰动是影响坦克炮射击精度的重要因素，为研究弹丸出炮口瞬间的炮口扰动规律，基于多体动力学与有限元方法构建了坦克刚柔耦合的全车动力学仿真模型，该模型考虑了身管的柔性特性，对身管进行了模态分析，得到了身管的模态中性文件。通过仿真，对比了后坐部分最大后坐位移与最大后坐速度的试验值与仿真值，对刚柔耦合模型的仿真结果进行了验证。在此基础上，分析了刚性身管和柔性身管对炮口扰动的影响，结果表明：考虑身管柔性特性的刚柔耦合模型能够有效提高坦克炮射击仿真精度。     

Real-time prediction of projectile penetration to laminates by training machine learning models withfinite element solver as the trainer

Studies on ballistic penetration to laminates is complicated, but important for design effective protection of structures. Experimental means of study is expensive and can often be dangerous. Numerical simu-lation has been an excellent supplement, but the computation is time-consuming. Main aim of this thesis was to develop and test an effective tool for real-time prediction of projectile penetrations to laminates by training a neural network and a decision tree regression model. A large number of finite element models were developed;the residual velocities of projectiles fromfinite element simulations were used as the target data and processed to produce sufficient number of training samples. Study focused on steel 4340tpolyurea laminates with various configurations. Four different 3D shapes of the projectiles were modeled and used in the training. The trained neural network and decision tree model was tested using independently generated test samples using finite element models. The predicted projectile velocity values using the trained machine learning models are then compared with thefinite element simulation to verify the effectiveness of the models. Additionally, both models were trained using a published experimental data of projectile impacts to predict residual velocity of projectiles for the unseen samples. Performance of both the models was evaluated and compared. Models trained with Finite element simulation data samples were found capable to give more accurate predication, compared to the models trained with experimental data, becausefinite element modeling can generate much larger training set, and thus finite element solvers can serve as an excellent teacher. This study also showed that neural network model performs better with small experimental dataset compared to decision tree regression model.     

Damage modeling of ballistic penetration and impact behavior of concrete panel under low and high velocities

This work presents a numerical simulation of ballistic penetration and high velocity impact behavior of plain and reinforced concrete panels. This paper is divided into two parts. The first part consists of numerical modeling of reinforced concrete panel penetrated with a spherical projectile using concrete damage plasticity (CDP) model, while the second part focuses on the comparison of CDP model and Johnson-Holmquist-2 (JH-2) damage model and their ability to describe the behavior of concrete panel under impact loads. The first and second concrete panels have dimensions of 1500 mm × 1500 mm × 150 mm and 675 mm × 675 mm × 200 mm, respectively, and are meshed using 8-node hexahedron solid elements. The impact object used in the first part is a spherical projectile of 150 mm diameter, while in the second part steel projectile of a length of 152 mm is modeled as rigid element. Failure and scabbing characteristics are studied in the first part. In the second part, the com-parison results are presented as damage contours, kinetic energy of projectile and internal energy of the concrete. The results revealed a severe fracture of the panel and high kinetic energy of the projectile using CDP model comparing to the JH-2 model. In addition, the internal energy of concrete using CDP model was found to be less comparing to the JH-2 model.     

旋转弹体入水弹道的计算方法

借助已有的实验资料与经验 ,给出了弹体入水空泡的数学模型 ;分析了旋转弹体与空泡壁相互作用引起的弹体上的流体动力特性 ,提出了一种预测旋转弹体入水弹道的计算方法     

Damage of multi-layer spaced metallic target plates impacted by radial layered PELE

Three different kinds of PELE (the penetrator with lateral efficiency) were launched by ballistic artillery to impact the multi-layer spaced metal target plates. The impact velocities of the projectiles were measured by the velocity measuring system. The damage degree and process of each layer of target plate impacted by the three kinds of projectiles were analyzed. The experimental results show that all the three kinds of projectiles have the effect of expanding holes on the multi-layer spaced metal target plates. For the normal structure PELE(without layered) with tungsten alloy jacket and the radial layered PELE with tungsten alloy jacket, the diameters of holes on the second layer of plates are 3.36 times and 3.76 times of the diameter of the projectile, respectively. For radial layered PELE with W/Zr-based amorphous composite jacket, due to the large number of tungsten wires dispersed after the impact, the diameter of the holes on the four-layer spaced plates can reach 2.4 times, 3.04 times, 5.36 times and 2.68 times of the diameter of the projectile. Besides, the normal structure PELE with tungsten alloy jacket and the radial layered PELE whit tungsten alloy jacket formed a large number of fragments impact marks on the third target plate. Although the number of fragments penetrating the third target plate is not as large as that of the normal structure PELE, the area of dispersion of fragments impact craters on the third target plate is larger by the radial layered PELE. The radial layered PELE with W/Zr-based amorphous composite jacket released a lot of heat energy due to the impact of the matrix material, and formed a large area of ablation marks on the last three target plates.     

Interface defeat studies of long-rod projectile impacting on ceramic targets

The interface defeat phenomenon always occurs when a long-rod projectile impacting on the ceramic target with certain velocity, i.e., the projectile is forced to flow radially on the surface of ceramic plates for a period of time without significant penetration. Interface defeat has a direct effect upon the ballistic performance of the armor piercing projectile, which is studied numerically and theoretically at present. Firstly, by modeling the projectiles and ceramic targets with the SPH (Smoothed Particle Hydrodynamics) particles and Lagrange finite elements, the systematic numerical simulations on interface defeat are performed with the commercial finite element program AUTODYN. Three different responses, i.e., complete interface defeat, dwell and direct penetration, are reproduced in different types of ceramic targets (bare, buffered, radially confined and oblique). Furthermore, by adopting the validated numerical algorithms, constitutive models and the corresponding material parameters, the influences of projectile (material, diameter, nose shape), constitutive models of ceramic (JH-1 and JH-2 models), buffer and cover plate (thickness, constraints, material), as well as the prestress acted on the target (radial and hydrostatic) on the interface defeat (transition velocity and dwell time) are systematically investigated. Finally, based on the energy conservation approach and taking the strain rate effect of ceramic material into account, a modified model for predicting the upper limit of transition velocity is proposed and validated. The present work and derived conclusions can provide helpful reference for the design and optimization of both the long-rod projectile and ceramic armor.     

旋成体射弹倾斜入水运动仿真

为了研究运动参数和弹头外形对弹体斜入水过程的影响规律,采用气液两相流体积分数和水汽空化模型,通过嵌套网格实现刚体三自由度运动学和动力学耦合,模拟了弹体以80～100 m/s速度倾斜入水开空泡阶段的运动过程。经文献实验验证,入水弹体速度与位移的误差为0～6%和-8%～0,转动角度误差为-6%～0。通过对入水速度和入水角度的多工况模拟研究,发现入水速度增大,弹体轴向冲击载荷增大,最大载荷与速度的平方呈线性关系,弹体速度非线性衰减率大;入水角增大,弹体转动角速率减小,运动稳定性强,速度衰减率不受入水角影响。与圆锥头部弹体相比,采用头部阶梯状修型后的弹体的平均速度衰减率、转动角速率和最大轴向冲击载荷分别降低到66.7%、40%和77.2%,显著提高了运动稳定性。     

An air cavity method for increasing the underwater acoustic targets strength of corner reflector

In order to improve the underwater acoustic target strength of corner reflectors, according to the principle of acoustic impedance mismatch of the boundary layer, the method of using air cavity to increase the underwater acoustic target strength of corner reflectors is proposed. The acoustic reflection coefficients of underwater air layer and single layer metal sheet are calculated and compared. The results show that the reflection coefficient of single layer metal sheet is greatly affected by frequency and incidence angle, and the reflection coefficient of air layer in water is large and little affected by frequency and incidence angle. On this basis, a new kind of airfilled cavity corner reflector is designed. The acoustic scattering characteristics of underwater airfilled cavity corner reflector are calculated cumulatively, and the results are compared with the monolayer metal sheet corner reflector. The simulation results show that the acoustic reflection effect of the airfilled cavity corner reflector is better. In order to verify the correctness of the method, the test was carried out in the silencing tank. The experimental results show that the simulation results are in good agreement with the experimental results, and the airfilled cavity can improve on acoustic reflection performance of the underwater corner reflector.     

基于可执行模型架构的成像侦察卫星系统建模与仿真

成像侦察卫星系统内部关系复杂、任务需求种类较多,利用基于町执行模型架构的系统工程对其进行建模研究,可以有效地实现从模型到仿真的综合集成．通过研究可执行模型架构理论,集成UPDM与成像侦察卫星系统功能模型,对成像侦察卫星系统进行了建模与仿真,验证了可执行模型架构的有效性与实用性．     

随移动窗推进的带电粒子束团长程传输模拟分析

直接采用粒子模拟方法较难实现带电粒子束团千米量级的长程传输模拟,针对此问题以静电模型为基础,引入移动窗技术,使百米量级的粒子传输窗口与束团同步推进运动,建立了带电粒子束团的长程传输模型。将模拟得到的带电粒子束团径向膨胀特性同包络方程的计算结果进行对比,两者吻合较好,证明了在带电粒子束团长程传输模拟研究中结合移动窗技术的可行性及所建模型的合理性。利用此模型分析了100 MeV相对论电子束团的长程传输过程,发现传输过程中束团的自生电场和磁场在径向上呈高度对称分布,轴向上则呈轻微前冲分布;同时,束团内部粒子的轴向速度分布也会发生变化。利用此模型分析了100 MeV电子束团的长程传输过程及其内部参数和自生场量的变化。     

Aerodynamics analysis of a hypersonic electromagnetic gun launched projectile

A hypersonic aerodynamics analysis of an electromagnetic gun (EM gun) launched projectile configuration is undertaken in order to ameliorate the basic aerodynamic characteristics in comparison with the regular projectile layout. Static margin and pendulum motion analysis models have been applied to evaluate the flight stability of a new airframe configuration. With a steady state computational fluid dynamics (CFD) simulation, the basic density, pressure and velocity contours of the EM gun projectile flow field at Mach number 5.0, 6.0 and 7.0 (angle of attack = 0°) have been analyzed. Furthermore, the static margin values are enhanced dramatically for the EM gun projectile with configuration optimization. Drag, lift and pitch property variations are all illustrated with the changes of Mach number and angle of attack. A particle ballistic calculation was completed for the pendulum analysis. The results show that the configuration optimized projectile, launched from the EM gun at Mach number 5.0 to 7.0, acts in a much more stable way than the projectiles with regular aerodynamic layout.     

火药脉冲助推器控制在舰载火箭弹中的应用

建立了采用火药脉冲助推器控制的简易制导火箭弹的弹道模型 ,进行了数字仿真 .理论研究和数字仿真结果表明 ,采用火药脉冲助推器控制可以有效地提高火箭弹的命中精度 ,它对实际弹道修正的效果与其冲量大小、数目、作用起始时刻、作用方位角、作用时间间隔等因素有关     

Experimental investigation on enhanced damage to fuel tanks by reactive projectiles impact

Enhanced damage to the full-filled fuel tank,impacted by the cold pressed and sintered PTFE/AL/W reactive material projectile(RMP)with a density of 7.8 g/cm3,is investigated experimentally and theoretically.The fuel tank is a rectangular structure,welded by six pieces of 2024 aluminum plate with a thickness of 6 mm,and filled with RP-3 aviation kerosene.Experimental results show that the kerosene is ignited by the RMP impact at a velocity above 1062 m/s,and a novel interior ignition phenomenon which is closely related to the rupture effect of the fuel tank is observed.However,the traditional steel projectile with the same mass and dimension requires a velocity up to 1649 m/s to ignite the kerosene.Based on the experimental results,the radial pressure field is considered to be the main reason for the shear failure of weld.For mechanism considerations,the chemical energy released by the RMP enhances the hydrodynamic ram(HRAM)effect and provides additional ignition sources inside the fuel tank,thereby enhancing both rupture and ignition effects.Moreover,to further understand the enhanced ignition effect of RMP,the reactive debris temperature inside the kerosene is analyzed theoretically.The initiated reactive debris with high temperature provides effective interior ignition sources to ignite the kerosene,resulting in the enhanced ignition of the kerosene.     

Study of high-speed interaction processes between fluoropolymer projectiles and aluminum-based targets

The experimental results and numerical modeling of penetration process of fluoropolymer projectiles in aluminum-based targets are presented. Analysis of mathematical models for interaction of elastoplastic projectile and target without taking additional energy released during interaction of fluoropolymer and aluminum into consideration is carried out. Energy fraction which is spent effectively on the increase in cavity volume is determined. The experimental and calculated results of penetration by combined and inert projectiles are compared.     

弹道导弹反拦截作战中子母弹抛撒方法研究

以弹道导弹突破“爱国者”反导弹为背景 ,研究了一种通过调整子母弹抛撒高度提高突防能力的方法。通过对所建子母弹飞行动力学模型的仿真 ,计算出子母弹不被拦截的最优抛撒高度 ,同时也计算了该抛撒高度下子弹抛撒圆的半径及其抛撒误差 ,为作战应用提供了理论基础     

路面对坦克火炮动态特性影响的计算机模拟

就不平地面行驶时坦克火炮系统的动态特性进行了动力学建模和仿真,主要包括:通过随机抽样法建立双侧不平地面模型,采用状态方程法建立三维车体、双侧任意车轮、任意位置座椅在内的坦克底盘的振动模型、火炮的运动模型,并编制相应的程序进行了仿真。将路面-坦克-火炮相互作用过程体现出来,更加全面和客观地反映了坦克行进过程中火炮的动态特性,比实车测量法获得火炮运动特性的方法更为高效和系统,对于坦克火控系统的综合仿真有着积极的作用。