卫星中心承力筒结构优化设计研究

利用有限元软件ANSYS建立复合材料中心承力筒式卫星平台结构的参数化有限元分析模型,计算了整星结构振动模态,在此基础上对复合材料蜂窝夹层中心承力筒结构分析模型进行简化,在满足结构的强度、变形、振动和屈曲约束条件下,对承力筒结构进行优化设计,并对多种方案进行比较,提出的方法和思路为今后同类结构设计提供了参考。     

尾座式电动飞机复合材料机翼结构优化设计

以复杂地形地区物资快速投送平台设计为背景,开展尾座式电动飞机复合材料机翼设计研究。对机翼结构载荷进行分析,对机翼结构构件布置和铺层进行设计,形成复合材料机翼结构设计方案。建立复合材料机翼结构有限元模型,开展典型工况条件下的静力分析,得到机翼结构变形、应力和Tsai-Wu失效因子分布。采用分步优化策略,以机翼结构铺层厚度和铺层角度为设计变量,开展机翼结构质量优化计算,优化结果表明,优化后的机翼结构在满足强度和刚度要求下质量减轻约47.77%,可为尾座式电动飞机结构设计提供重要参考。     

Optimization of buckling load for laminated composite plates using adaptive Kriging-improved PSO: A novel hybrid intelligent method

An effective hybrid optimization method is proposed by integrating an adaptive Kriging (A-Kriging) into an improved partial swarm optimization algorithm (IPSO) to give a so-called A-Kriging-IPSO for maxi-mizing the buckling load of laminated composite plates (LCPs) under uniaxial and biaxial compressions. In this method, a novel iterative adaptive Kriging model, which is structured using two training sample sets as active and adaptive points, is utilized to directly predict the buckling load of the LCPs and to improve the efficiency of the optimization process. The active points are selected from the initial data set while the adaptive points are generated using the radial random-based convex samples. The cell-based smoothed discrete shear gap method (CS-DSG3) is employed to analyze the buckling behavior of the LCPs to provide the response of adaptive and input data sets. The buckling load of the LCPs is maximized by utilizing the IPSO algorithm. To demonstrate the efficiency and accuracy of the proposed methodology, the LCPs with different layers (2, 3, 4, and 10 layers), boundary conditions, aspect ratios and load patterns (biaxial and uniaxial loads) are investigated. The results obtained by proposed method are in good agreement with the literature results, but with less computational burden. By applying adaptive radial Kriging model, the accurate optimal results-based predictions of the buckling load are obtained for the studied LCPs.     

基于ANSYS的油罐拱顶稳定性分析

针对加肋拱顶稳定性十分复杂的问题,基于ANSYS建立了加肋拱顶油罐的三维有限元模型,对加肋拱顶的结构稳定性进行了数值模拟。对加肋拱顶在外压作用下的线性与非线性临界屈曲载荷进行了对比分析,利用弧长法获得了拱顶在加肋情况下径向、环向、轴向的载荷-位移曲线。结果表明:数值模拟的加肋拱顶屈曲方向和屈曲区域与实际失稳结果相一致,可以为加肋拱顶设计和稳定性分析提供一定参考。     

喷嘴结构对高压水射流影响及结构参数优化设计

喷嘴是产生高压水射流的关键部件,其结构形式对射流动力学性能有很大影响。以圆柱形喷嘴为对象,进行喷嘴结构对高压水射流的影响分析及结构参数优化设计。采用两相流计算流体力学模型进行喷嘴内外的射流流场分析。为节省计算资源,在优化设计时引入Kriging代理模型替代计算流体力学模型。分别采用改进的非劣分类遗传算法和基于分解的多目标进化算法进行单目标和多目标优化设计。研究结果表明:直线型喷嘴总体性能较优,凹型喷嘴的次之,凸型喷嘴性能最差。以直线型喷嘴为设计对象,以射流初始段长度和流量为目标,得到了单目标和多目标优化设计结果。单目标优化时,两个指标较基准外形分别提高14.71%和27.56%。多目标优化时,优化得到的半锥角处于[15.4°,89.8°]区间内。运用代理模型和进化算法的全局优化方法在进行喷嘴的优化设计时是有效的。     

基于静力与稳定性分析的小卫星主接头选型优化

基于对预埋主接头蜂窝板的静力与稳定性分析,对小卫星主接头进行选型优化。采用三明治夹心板理论建立预埋分叉式和面板式小卫星主结构连接接头的蜂窝板试件有限元模型,分析得到了蜂窝板最大应力值与失稳载荷,通过与试验结果的对比分析确定了蜂窝板试件破坏原因。在此基础上讨论结构参数对蜂窝板承载性能的影响,确定出最优的接头设计形式。     

Multiobjective optimization of friction welding of UNS S32205 duplex stainless steel

The present study is to optimize the process parameters for friction welding of duplex stainless steel(DSS UNS S32205).Experiments were conducted according to central composite design.Process variables,as inputs of the neural network,included friction pressure,upsetting pressure,speed and burn-off length.Tensile strength and microhardness were selected as the outputs of the neural networks.The weld metals had higher hardness and tensile strength than the base material due to grain refinement which caused failures away from the joint interface during tensile testing.Due to shorter heating time,no secondary phase intermetallic precipitation was observed in the weld joint.A multi-layer perceptron neural network was established for modeling purpose.Five various training algorithms,belonging to three classes,namely gradient descent,genetic algorithm and LevenbergeM arquardt,were used to train artificial neural network.The optimization was carried out by using particle swarm optimization method.Confirmation test was carried out by setting the optimized parameters.In conformation test,maximum tensile strength and maximum hardness obtained are 822 MPa and 322 Hv,respectively.The metallurgical investigations revealed that base metal,partially deformed zone and weld zone maintain austenite/ferrite proportion of 50:50.     

Crashworthiness performance of hybrid kenaf/glass fiber reinforced epoxy tube on winding orientation effect under quasi-static compression load

This research was aimed to study the effect winding orientation on the crashworthiness performance of hybrid tube. The specimens tested under quasi-static compression load involve of three winding parameters (θ = 30°, 45° and 70°) of hybrid kenaf/glass fiber reinforced epoxy and glass fiber reinforced epoxy as contrast specimen. The automated filament winding technique has been used in fabrication of hybrid and non-hybrid composite tube and crashworthiness performance was investigated experimentally. The effects of winding orientation on energy absorption capabilities and crashworthiness characteristic were investigated through quasi-static compression load and the result are compared with the glass fiber composite tube to justify the capability of hybrid natural/synthetic as energy absorption application. Hybridized samples proved to enhancing the progressive crushing capability as combination of local buckling, delaminate and brittle fracturing as progressive crushing modes.In the view of winding orientation aspect, the results of high winding orientation of hybrid composite tube elevated the crush load efficiency, specific energy absorption and energy absorption capability compared to glass composite tube (GFRP). The hybrid kenaf/glass composite tube with high winding orientation showed the best winding orientation to enhance the energy absorber characteristics as energy absorption application.     

应用Isight的复合材料桁架结构优化设计

轻质复合材料及其结构以其优异的力学性能在航天航空飞行器上得到了广泛应用。考察玻璃纤维/环氧复合材料方形截面桁架在典型弯曲载荷工况条件下的非线性结构承载性能。采用Isight集成平台对桁架结构进行多参数优化设计,获得满足结构刚度和承载性能要求的最轻质桁架结构的几何参数,并分析最优化结构在载荷作用下的结构非线性响应行为。结果表明采用Isight平台对桁架结构进行多参数优化设计具有较高的效率和可信度。     

基于粒子群算法的H_∞混合灵敏度控制研究

针对步进电机存在负载摄动和失步超步问题,提出了一种基于粒子群优化算法的混合灵敏度设计方法。在H∞混合灵敏度约束下,采用粒子群算法寻找能够反映系统特性的适应度函数最优值,在搜索到合适的加权阵基础上,利用Matlab得到了H∞最优控制器,并利用优化控制器对步进电机进行控制仿真实验。实验结果表明：该系统具有响应快速平稳、抗负载扰动强等特点。     

混合模糊测试中混合符号执行优化策略评估与分析

针对传统混合模糊测试提升技术多聚焦于利用多种动静态分析手段辅助而忽略了混合符号执行自身性能的问题,提出一种混合模糊测试平衡点模型,并基于该模型对主流混合符号执行方案进行剖析,包括污点分析辅助模糊测试、混合模糊测试以及混合符号执行,归纳了6种符号执行方案,基于混合符号执行引擎Triton复现了6种符号执行方案,并通过10个典型真实程序进行了测试评估。从效率、内存、覆盖率三个维度对各个方案进行性能对比与影响因素分析。实验证明,优化方案都可以消除不必要的约束并减少时间和空间开销,但约束缩减会造成信息丢失,造成覆盖率降低。基于实验数据分析,提出了一个优化方案的性能序列,并提出三种针对不同测试需求的优化方案。     

Beginning of the End: ARVN and Vietnamisation (1969–72)

The ‘Nixon Doctrine,’ announced on 25 July 1969, which emphasised the singularity of US interest over all others, was a reflection of US war weariness and the President Richard Nixon's political constraints. The net effect was the unilateral withdrawal of troops in phases and Vietnamisation returning combat responsibilities to the South Vietnamese. Indeed, negotiations and diplomacy fell short of expectations, failing to force the North Vietnamese to abandon their objectives. However, Vietnamisation, the third leg of Nixon's strategy, became the most visible of Nixon's failures. Such was the debacle that Nixon was sorely tempted to simply walk away concluding, ‘Vietnamization has been completed and [South Vietnam President Nguyen Van] Thieu then can do what he likes.’     

复合材料圆锥壳稳定性分析的传递函数法

基于线弹性小变形理论， 利用Ｆｏｕｒｉｅｒ级数展开、Ｌａｐｌａｃｅ 变换和摄动方法， 建立了复合材料薄壁圆锥壳的静力响应、频率响应、自由振动与屈曲特征值问题的渐近传递函数解。构造了复杂边界条件、中间带支撑、变锥度及阶梯变厚度圆锥壳的传递函数解。数值计算结果表明该方法具有很高的计算精度。     

基于边界交叉法的高超声速滑翔飞行器多目标轨迹优化研究

针对高超声速滑翔飞行器复杂约束条件下多目标轨迹设计问题，基于边界交叉法和伪谱法提出了其多目标轨迹优化方法。首先，分析了高超声速滑翔飞行器复杂约束轨迹优化问题的特点，提出了多目标轨迹优化问题。然后，采用边界交叉法和伪谱法将多目标轨迹优化问题转化为一组单目标优化子问题，利用非线性规划算法分别求解。在优化过程中，将已求解子问题的解作为下一个子问题的初始值。利用上述方法求解了最大横程和最小峰值热流轨迹优化问题，仿真结果表明：本文方法能够有效搜索到优化轨迹的Pareto前沿，可以为高超声速滑翔飞行器轨迹设计提供参考。     

圆柱壳稳定性分析的一种新方法

针对圆柱壳在复杂载荷作用下静力稳定性问题提出了一种新的求解方法.基于分离变量的方法,设定一组可涵盖任意边界条件的复数位移函数,将位移函数代入系统平衡方程后,圆柱壳的静力稳定性问题就可以转化为一个复系数八次多项式的求根问题.该特征方程的偶次幂系数项以及常数项为实数,而奇数次幂项均为纯虚数.研究表明,根的大小代表了圆柱壳端部作用力的强度,以及该作用力在离开这个边界一定距离上的衰减特性.分析了该新方法和经典方法的关系,并给出了一个各向同性圆柱壳在轴向压力作用下稳定性分析算例,得到了线弹性失稳解.和经典方法的结果比较表明,文中所提出的新方法适用可行,且和经典方法具有同样的精度.     

A technique which combines modified pattern search methods with composite designs and polynomial constraints to solve constrained optimization problems

This paper presents a method of selecting design parameters which optimizes a specific measure (aircraft design example: minimum weight, maximum mission effectiveness) and guarantees designated levels of response in specified areas (such as combal ceiling, acceleration time). The method employs direct search optimization applied to a nonlinear functional constrained by nonlinear surfaces. The composite design technique is combined with regression methods to determine adequate surface representations with a minimum of required data points. A sensitivity analysis is conducted at the optimum set of design parameters to test for uniqueness.     

助推—滑翔式导弹中段弹道方案的初步分析

建立了助推—滑翔式弹道中段的无量纲运动方程。采用非线性规划方法实现弹道优化。首先求解不同初始速度、速度倾角和最大升阻比的最大射程弹道,然后考虑驻点热流、过载约束,求解总气动加热最小和射程最大的最优弹道。基于前者的计算结果分析了初始条件对最大射程弹道的影响。将考虑约束的再入滑翔弹道与弹道式再入的特征参数比较,表明再入滑翔弹道的峰值热流较小,而总气动加热增加,但再入滑翔飞行时间在一般锥形体再入机动飞行器的热防护系统可承受的时间范围内。     

钢筋混凝土楼板耐火当量时间研究

从隔热性方面研究钢筋混凝土楼板的耐火极限，以室内火灾轰燃后的房间热平衡和热传导理论为基础，以钢筋混凝土楼板火灾中背火面的最高温度相等为原则，用计算机数值分析方法计算出楼板的隔火当量时间，并用最小二乘法回归出当量时间关于火灾荷栽密度和开口因子的计算公式，结果可使设计方法得到简化，为性能化耐火设计提供一定的参考。     

潜艇概念设计阶段的多目标优化研究

研究了潜艇在概念设计阶段的多目标优化问题。基于多目标遗传算法(MOGA),把潜艇航速和排水量这两个概念设计阶段的重要属性作为目标函数,考虑了浮力平衡和水下稳性等约束条件,研究了潜艇主尺度确定的问题。计算了一个潜艇概念的数值算例,给出了多目标优化问题的Pareto前沿。文中给出的方法能够快速求解多目标优化解,为实际的潜艇设计提供参考。