铝合金-纯铝-钢复合板爆炸焊接试验及性能研究

通过设计爆炸焊接试验复合了铝合金-纯铝-钢爆炸复合板,对其界面形态、显微硬度及力学性能进行了研究。结果表明,铝合金-纯铝界面纯规则正弦波形,纯铝-钢复合板界面波形较小,铝合金-纯铝-钢复合板的界面剪切强度在75 MPa以上,爆炸复合过程中,纯铝与钢界面生成了金属间化合物,其界面处基体金属发生强烈的塑性变形。复合板变形及组织变化的结果造成复合板界面处的显微硬度最高,随着距界面距离的增加,两侧基体金属的硬度逐渐降低。     

单个球形装药浅层水中爆炸的试验研究

装药浅层水中爆炸研究是一个分复杂的问题。本文支用爆炸相似律对浅层水中爆炸冲击波参数进行了分析,并测试了水中冲以压力值。根据试验结果,本文对空间流场压力分布进行了分析并建立了模型进行了试验范围内冲击波压力的经验公式。     

封闭式爆炸容器小药量爆炸振动效应研究

为评估炸药在封闭容器内爆炸产生的振动效应对周围环境的影响,对封闭式爆炸容器小药量TNT炸药爆炸产生的爆炸振动效应进行了爆源邻近实地监测和测试。结果表明:小药量炸药爆炸引起的爆炸振动效应对距爆源100 m以外的普通砖结构民用住宅产生的速度强度远低于其临界峰值速度,不会对其结构产生明显影响。     

近场爆炸作用下简支钢筋混凝土梁冲剪破坏的预测方法

爆炸作用下钢筋混凝土梁会呈现多种破坏模式,针对近场爆炸载荷作用下钢筋混凝土梁的冲剪破坏,联合等效单自由度模型和临界剪切裂纹理论,提出一种预测钢筋混凝土梁冲剪破坏的方法,并通过开展两发球形梯恩梯装药近场爆炸试验,观察了钢筋混凝土梁的破坏形态,验证了冲剪破坏的预测方法.结果表明:提出的预测方法可用来评估钢筋混凝土梁在近场爆...     

爆炸场冲击波测试装置电磁屏蔽结构研究

为了减小弹药爆炸电磁辐射对测试的影响,提出了一种铝、坡莫合金组成双层屏蔽结构,采用Ansoft Maxwell对其屏蔽效果进行了仿真,与铝壳、钢壳的屏蔽效果对比,并进行了验证.结果表明:在模拟爆炸场环境中,3种壳体内的磁感应强度铝壳的最大为3.339 1×10-7 T;钢壳为1.960 1×10-7T;采用双层屏蔽的为...     

金属靶体材料动力硬度测试及动态阻力分析

以高速侵彻下45钢靶体侵彻阻力为研究对象,开展了弹体高速侵彻45钢靶体试验,获取了典型弹体对45钢靶体的成坑参数。基于高速侵彻阻力模型对靶体侵彻阻力及影响因素进行分析。结合流体动力学侵彻模型对不同弹体材料侵彻45钢靶体侵彻深度规律进行研究。研究结果表明:随着撞击速度的增大,45钢的靶体阻力从5. 13 GPa减小到3. 7 GPa;基于材料动力硬度测试方法的靶体动态阻力测试结果和理论计算结果吻合较好;随着靶体动态屈服强度的增大,靶体阻力呈线性增大的趋势;侵彻深度及靶体动态阻力理论计算结果和试验数据吻合较好,说明所提动态阻力确定方法可行,可为高速侵彻动力学研究提供参考。     

钢—混凝土复合爆炸容器内爆响应数值模拟

应用动力有限元方法模拟了轴对称椭球顶圆柱密闭式抗爆容器内部爆炸流场,并对钢衬-混凝土复合容器壁的应力应变响应进行了数值模拟分析.分析结果显示:钢衬层应力波动的低、高频两部分分别起因于压力波的反复作用及钢衬结构的本征振动,二次波对容器顶部的作用很重要,并由此对混凝土的塑性及损伤的时空分布产生重要影响.数值模拟结果与实验结果一致.     

考虑抗拉强度的含外倾结构面岩质边坡稳定性分析

当前工程设计都是将边坡失稳破坏看成整体的剪切破坏即M-C剪切破坏,基本不考虑岩土体本身抗拉强度.而岩质边坡真实的破坏应该是张拉-剪切复合破坏,不应是传统不考虑抗拉强度的单一剪切破坏模式.利用FLAC3D软件,基于张拉-剪切复合破坏准则对岩体和结构面强度参数同时进行强度折减,与只考虑抗剪强度的情况进行比较来研究抗拉强度对...     

不同材料壳体装药在空气中爆炸威力试验研究

为评估装药壳体材料对爆炸毁伤威力的影响,对裸装药、碳纤维复合壳体、钢壳体装药在空气中的爆炸破坏效应进行了试验研究,试验获得了3种装药冲击波超压曲线.试验结果表明,同样装药情况下,裸装药爆炸冲击渡超压大于带壳装药,碳纤维复合材料壳体装药爆炸产生的冲击波超压相对钢壳体装药高,且不会产生破片对远距离目标造成破坏;而钢壳体装药爆炸产生的破片对远距离目标具有一定的杀伤效应.     

FRC/钢嵌入式L型单向接头改进设计及失效机理

针对梅志远等提出的FRC/钢嵌入式单向接头所存在的初始损伤强度值偏低,不利于连接结构完整性的问题,提出了改进设计方案。通过开展改进型接头单向拉伸极限承载强度试验研究,验证了改进措施的有效性;利用Abaqus非线性显示求解技术和Cohesive界面模拟技术对接头承载特性进行仿真分析,进一步探讨了改进型单向接头承载应力分布特征、损伤演变规律以及连接失效机理。研究结果表明:改进设计方案初始损伤线强度值比梅志远等提出的结构方案提高了2~3倍;初始损伤主要表现为凹槽内表面FRC/钢粘结界面的剪切剥离。     

舰船静置爆炸气泡时总纵强度计算方法研究

新型"大气泡能"概念武器在水下爆炸能产生大气泡,对船体总纵强度造成很大影响,有可能使舰体发生纵向折断或倾覆。为研究这种作用,建立了舰船静置爆炸气泡时总纵弯曲强度的理论计算方法。采用静置爆炸气泡的假设,将气泡产生的浮力损失和压力差转化为等效载荷,计算气泡作用后船体的总纵弯矩和剪力并进行强度校核。以某舰艇为例进行计算,结果表明,爆炸气泡作用下船体的剪力和弯矩比静浮状态增大很多,船体发生纵向折断破坏的危险性也随之增大。     

An interface shear damage model of chromium coating/steel substrate under thermal erosion load

The Cr-plated coating inside a gun barrel can effectively improve the barrel's erosion resistance and thus increase the service life.However,due to the cyclic thermal load caused by high-temperature gun-powder,micro-element damage tends to occur within the Cr coating/steel substrate interface,leading to a gradual deterioration in macro-mechanical properties for the material in the related region.In order to mimic this cyclic thermal load and,thereby,study the thermal erosion behavior of the Cr coating on the barrel's inner wall,a laser emitter is utilized in the current study.With the help of in-situ tensile test and finite element simulation results,a shear stress distribution law of the Cr coating/steel substrate and a change law of the interface ultimate shear strength are identified.Studies have shown that the Cr coating/steel substrate interface's ultimate shear strength has a significant weakening effect due to increasing temperature.In this study,the interfacial ultimate shear strength decreases from 2.57 GPa(no erosion)to 1.02 GPa(laser power is 160 W).The data from this experiment is employed to establish a Cr coating/steel substrate interface shear damage model.And this model is used to predict the flaking process of Cr coating by finite element method.The simulation results show that the increase of coating crack spacing and coating thickness will increase the service life of gun barrel.     

Three-dimensional coordinates test method with uncertain projectile proximity explosion position based on dynamic seven photoelectric detection screen

To objectively obtain the three-dimensional coordinates of the projectile fuze proximity explosion when projectile intersects the head of missile target, we propose a dynamic seven photoelectric detection screen test method, which is made up of six plane detection screens and a flash photoelectric dynamic detection screen. The three-dimensional coordinates calculation model of the projectile proximity explosion position based on seven plane detection screens with dynamic characteristics is established. According to the relation of the dynamic seven photoelectric detection screen planes and the time values, the analytical function of the projectile proximity explosion position parameters under non-linear motion is derived. The projectile signal filtering method based on discrete wavelet transform is explored in this work. Additionally, the projectile signal recognition algorithm using an improved particle swarm is proposed. Based on the characteristics of the time duration and the signal peak error for the projectile passing through the detection screen, the signals attribution of the same projectile passing through six detection screens are analyzed for obtaining precise time values of the same projectile passing through the detection screens. On the basis of the projectile fuze proximity explosion test, the linear motion model and the proposed non-linear motion model are used to calculate and compare the same group of projectiles proximity explosion position parameters. The comparison of test results verifies that the proposed test method and calculation model in this work accurately obtain the actual projectile proximity explosion position parameters.     

氧气体积分数对油气爆炸特性的影响

作为燃烧和爆炸三要素之一,氧气体积分数的控制对于爆炸事故的防治具有重要意义。实验研究了氧气体积分数对汽油蒸气-空气混合物（简称油气）爆炸极限和爆炸压力的影响。结果表明：随着氧气体积分数的降低,油气爆炸下限呈一阶指数规律缓慢增大,油气爆炸上限呈线性规律迅速减小;爆炸极限范围由0.92%~3.76%缩小为1点,该爆炸极限临界点为1.22%,对应的临界氧气体积分数为11.4%;油气的最大爆炸压力和最大压力上升速率随着氧气体积分数的降低而减小,油气体积分数越大,氧气体积分数影响越显著。     

粮食粉尘爆炸灭火救援对策研究

粮食粉尘爆炸燃烧时间长,破坏力大,易发生中毒和人员伤亡。介绍了粮食粉尘爆炸形成的特点,分析了粮食粉尘爆炸的条件及控制措施,探讨了粮食粉尘爆炸灭火救援对策。     

不同边界条件下水下爆炸气泡的数值模拟

采用有限元程序MSC.Dytran对不同边界条件下水下爆炸气泡的脉动过程进行了数值模拟。对数值模拟中的一些重要问题,如炸药药包的建模、网格密度、状态方程和静压力场的设定等问题进行了探讨。对无限水域中的水下爆炸气泡以及自由面边界、水平刚性面边界和垂直刚性面边界三种边界条件下的水下爆炸气泡进行了数值模拟,分析了水下爆炸气泡的半径、外形变化、气泡脉动压力、流场中的速度分布,结果发现边界的存在对气泡外形的影响较大,刚性边界面会使气泡脉动压力增大较多,而自由面边界对气泡脉动压力的影响较小。将数值模拟的结果与理论模型、经验公式和试验结果进行了比较分析,结果吻合较好。     

水下爆炸载荷作用下受损加肋圆柱壳的剩余屈曲强度计算

研究了在水下爆炸载荷作用下受损的加肋圆柱壳的屈曲.结合DYTRAN软件和NASTRAN软件计算了水下爆炸载荷作用下受损的加肋圆柱壳的剩余屈曲强度,并且提出了一种结合上述两种软件计算加肋圆柱壳的剩余屈曲强度的方法.数值计算表明,预测结果与实验结果吻合较好.     

Modeling of the whole process of shock wave overpressure of free-field air explosion

The waveform of the explosion shock wave under free-field air explosion is an extremely complex problem. It is generally considered that the waveform consists of overpressure peak, positive pressure zone and negative pressure zone. Most of current practice usually considers only the positive pressure. Many empirical relations are available to predict overpressure peak, the positive pressure action time and pressure decay law. However, there are few models that can predict the whole waveform. The whole process of explosion shock wave overpressure, which was expressed as the product of the three factor functions of peak, attenuation and oscillation, was proposed in the present work. According to the principle of explosion similarity, the scaled parameters were introduced and the empirical formula was absorbed to form a mathematical model of shock wave overpressure. Parametric numerical simulations of free-field air explosions were conducted. By experimental verification of the AUTODYN numerical method and comparing the analytical and simulated curves, the model is proved to be accurate to calculate the shock wave overpressure under free-field air explosion. In addition, through the model the shock wave overpressure at different time and distance can be displayed in three dimensions. The model makes the time needed for theoretical calculation much less than that for numerical simulation.     

Numerical investigation of the shockwave overpressure fields of multi-sources FAE explosions

Shockwaves from fuel-air explosive (FAE) cloud explosions may cause significant casualties. The ground overpressure field is usually used to evaluate the damage range of explosion shockwaves. In this paper, a finite element model of multi-sources FAE explosion is established to simulate the process of multiple shockwaves propagation and interaction. The model is verified with the experimental data of a fourfold-source FAE explosion, with the total fuel mass of 340 kg. Simulation results show that the overpressure fields of multi-sources FAE explosions are different from that of the single-source. In the case of multi-sources, the overpressure fields are influenced significantly by source scattering distance and source number. Subsequently, damage ranges of overpressure under three different levels are calculated. Within a suitable source scattering distance, the damage range of multi-sources situation is greater than that of the single-source, under the same amount of total fuel mass. This research provides a basis for personnel shockwave protection from multi-sources FAE explosion.     

某石化公司6·28爆炸火灾事故原因认定

通过介绍一起石油化工装置爆炸火灾原因调查案例，阐述了运用现场勘验、调查访问、技术测试、逻辑分析等方法，认定装置爆炸火灾原因的过程。