动力车纵向气动力风洞试验及数值模拟

采用风洞试验(在地板抽吸和不抽吸情况下)和数值模拟计算对200km/h动力集中型电动旅客列车组动力车纵向气动力进行了研究,得到了动力车作为头、尾车的纵向气动力系数。结果表明,地板抽吸后,头、尾车空气阻力均有明显增加,头车负升力增加,尾车正升力减少;动力车头、尾两车联挂时底部空气阻力占总的空气阻力的25.9%,列车减阻的重点在车体底部空气阻力。     

旋转弹丸空气动力特性数值解法

为提高在弹道计算和弹丸设计中弹丸空气动力系数精度,采用隐式LU算法求解N S方程并考虑代数湍流模型,在旋转物面边界条件下计算弹丸的阻力、升力、俯仰力矩、滚转阻尼力矩、马格努斯力和力矩。通过对美国T388等弹丸的气动力系数计算并与弹道靶试验数据进行比较,以及对某榴弹的气动力计算结果在弹道计算中进行应用分析,表明用数值模拟得到的旋转弹丸空气动力系数好于以前用工程方法给出的结果。     

质量矩拦截器机动能力估算

首先介绍了质量矩拦截器的概念和特点,提出建立过载的速度是质量矩拦截器机动性的关键因素。通过建立简化的模型,得到了质量矩拦截器在俯仰平面内运动时建立攻角响应时间的解析表达式,并在此基础上进行了初步分析,表明质量矩拦截器具有很强的机动能力。     

不同攻角下AUV回收过程中的水动力规律

通过对AUV(Autonomous Underwater Vehicle)回收过程中运动规律的研究和对纳维—斯托克斯方程(Navier-Stokes equations)及其求解方法的分析,基于CFD(Computational Fluid Dynamics)理论建立了AUV回收运动的三维计算模型,并使用CFD软件完成其物理模型的建立、网格的划分及求解设置。在此基础上对AUV回收过程中的阻力、升力干扰进行分析计算,得到不同攻角下AUV所受到的水动力干扰与AUV和回收平台之间距离的相互联系。     

固定舵二维弹道修正组件结构模型

为了满足二维弹道修正组件小型化设计要求,设计了3种二维弹道修正组件模型,应用Solid Works软件和ICEM软件分别建立3种修正组件的实体模型和网格模型,并利用Fluent软件进行气动特性数值计算,将计算结果进行对比分析,得出不同修正组件模型参数对气动特性的影响。研究结果表明,修正组件尺寸的减小会增大阻力系数;舵片形状和尺寸对阻力系数和升力系数影响较小,但是对滚转力矩系数影响较大,矩形结构的舵片对舵片周围气动特性会产生不利影响;在满足修正要求的前提下,可以适当缩小舵片面积来降低舵机控制难度,提升飞行稳定性。     

考虑几何及力和力矩非线性时弹丸运动方程的研究

从矢量形式的六自由度弹丸运动方程组出发,推导出了在全部力和全部力矩作用下考虑几何非线性及力和力矩非线性时的弹丸运动方程组,并导出了其用于数值计算的柯西标准形式,得到了攻角和进动角的计算表达式.此动力学模型可用于弹丸大攻角飞行时的弹道计算及某些灵巧弹药(如末敏弹)的设计.     

Bang-Bang控制方式旋转导弹气动特性数值分析

为研究Bang-Bang控制式鸭舵对旋转导弹气动特性的影响,在CFD软件中采用嵌套网格方法模拟导弹的旋转和鸭舵的偏转,对Bang-Bang控制式旋转导弹在不同攻角、马赫数和转速下的气动特性进行了数值模拟,得到了气动特性变化规律。研究表明,因鸭舵洗流方向的改变,耦合导弹自旋会导致弹体和尾翼的侧向力发生突变。通过与不控鸭舵的旋转导弹进行对比,采用Bang-Bang控制式鸭舵的旋转导弹的周期平均侧向力系数变小,周期平均法向力系数变大。由于侧向力的存在,导弹在一个周期内的合力会偏离竖直方向,合力偏离竖直方向的角度随着马赫数、自旋速率和攻角的增大而减小。     

高超声速钝锥体俯仰阻尼导数影响因素分析

采用非定常双时间步长方法、刚性旋转动网格技术,结合空间隐式格式数值分析了高超声速钝锥体定常与非定常流场特征,并运用最小二乘法辨识出钝锥体的俯仰阻尼导数。通过与相应的实验数据、工程估算值进行比较,分析并验证了壁面网格雷诺数、钝头比、攻角与质心位置对钝锥体俯仰阻尼导数的影响。同时采用五种差分格式,其中包含五阶精度WENO与高精度WNND格式,对钝锥体俯仰阻尼导数进行了计算,结果表明不同无粘差分格式对俯仰静导数影响较小,但不同格式之间俯仰动导数结果存在差异,分析认为差分格式之间不同的粘性分辨率应是差异的主要来源。     

测试投稿，大家不要管哈~

采用非定常双时间步长方法、刚性旋转动网格技术,结合空间隐式格式数值分析了高超声速钝锥体定常与非定常流场特征,并运用最小二乘法辨识出钝锥体的俯仰阻尼导数。通过与相应的实验数据、工程估算值进行比较,分析并验证了壁面网格雷诺数、钝头比、攻角与质心位置对钝锥体俯仰阻尼导数的影响。同时采用五种差分格式,其中包含五阶精度WENO与高精度WNND格式,对钝锥体俯仰阻尼导数进行了计算,结果表明不同无粘差分格式对俯仰静导数影响较小,但不同格式之间俯仰动导数结果存在差异,分析认为差分格式之间不同的粘性分辨率应是差异的主要来源。     

远程火箭弹滑翔增程技术研究

基于火箭弹滑翔增程技术中采用的控制导弹法向过载和保持升阻比最优的2种滑翔控制方案,建立了滑翔弹道模型,分析了2种不同控制方案的约束条件,并进行了全弹道仿真,计算了不同下滑点对弹道增程的影响,为增程弹道控制方案的选择提供了依据.     

二维水翼空化流动的数值模拟

基于RANS方程,结合不同湍流模型与空化模型对粘性流中二维NACA66012模型水翼附近流场进行数值计算与模拟.计算得到固定攻角、固定来流速度时升力系数和阻力系数随空化数的变化规律以及固定空化数时升力系数随攻角的变化规律,并对相应流场进行分析.在二维水翼空化流动的准稳态模拟中,重点对比分析了不同湍流模型、空化模型对空化流动模拟结果的影响,并将计算结果与实验数据进行比较.研究结果表明,在二维水翼附近空化流动的数值模拟中,采用k-ω湍流模型和均相流空化模型计算得到的结果与实验数据吻合较好.最后,采用分离涡模型对不稳定的空化流动进行了瞬态模拟,并得到空化流动的变化规律.     

Formation of explosively formed penetrator with fins and its flight characteristics

The ultimate goal of weapon system employing an explosively formed penetrator (EFP) is to defeat a target at the longest standoff. In order to do this, an EFP must be aerodynamically stable so as to strike the target at a small angle of obliquity, and the decay velocity per meter of EFP must be smaller at extended standoff. As the angle of attack increases, the penetration ability of EFP greatly reduces. The fins improve the EFP aeroballistic characteristics and decrease the flight drag of EFP as well. EFP with fins formed by three-point initiation is presented. The formation of EFP with fins is studied by LS-DYNA, and the aeroballistics is studied through experiment. The experimental results show that the decay velocity per meter of EFP with fins is much smaller than that of normal EFP, and the attitude angle steadily decreases.     

正规形法在弹箭非线性运动分析中的应用

非线性气动力对弹箭运动特性具有重要影响,而其复杂性和有效分析工具的缺乏往往制约了弹箭非线性运动理论的发展.为探索正规形方法在弹箭非线性运动分析中的应用,构造了考虑二次非线性阻尼和七次非线性静力矩下攻角方程的正规形,进而求得攻角的通用解析解,通过数值积分验证了其在较大攻角范围内的有效性,该解析解也同样适用于无阻尼角运动和...     

凹槽构型对平板气层减阻影响试验分析

通过平板凹槽喷气减阻模型试验,研究了航速和气流量等因素对平板气层减阻规律的影响,并利用水下摄像系统对不同凹槽构型内的气层形态进行了观测。试验结果表明:不喷气时凹槽的存在会使平板的阻力增加;喷气可以有效减小平板阻力,存在饱和气流量;饱和气流量随着槽深的增加而减小,饱和气流量下平板的绝对减阻率随航速的增加而降低;设置凹槽构型是保持平板下表面气层稳定性的有效措施,合适的凹槽构型可以明显改善平板底部喷气流场,提高平板喷气减阻效果;在Fr为0.119时,饱和气流量下平板的绝对减阻率可以达到40%以上。     

高超声速飞行器分离干扰的伴随方法分析

以大气层内高超声速飞行器级间分离过程为研究对象,采用伴随方法得到了由冲击力和气动干扰力矩引起的攻角的解析解。利用该解析解,得到了分离干扰引起的攻角的瞬时变化曲线。结果表明,在高超声速飞行器级间分离开始0.4s内,冲击力和气动干扰力矩对攻角有一定的影响,并且随干扰的增大而增大。本研究实现了预示高超声速飞行器分离过程风险的目的,对高超声速飞行器分离干扰策略的制定提供了理论依据。     

Effect of change of sand properties on travel distance of ricocheted debris

The debris from exploded buildings can ricochet after colliding with the ground, thus increasing the debris travel distance and danger from any associated impacts or collisions. To reduce this danger, the travel distance of ricocheted debris must be accurately predicted. This study analyzed the change in the travel distance of ricocheted concrete debris relative to changes in the properties of a sand medium. Direct shear tests were conducted to measure the change in internal friction angle as a function of temperature and water content of the sand. Finite element analysis (FEA) was then applied to these variables to predict the speed and angle of the debris after ricochet. The FEA results were compared with results of low-speed ricochet experiments, which employed variable temperature and water content. The travel distance of the debris was calculated using MATLAB, via trajectory equations considering the drag coefficient. As the internal friction angle decreased, the shear stress decreased, leading to deeper penetration of the debris into the sand. As the loss of kinetic energy increased, the velocity and travel distance of the ricocheted debris decreased. Changes in the ricochet velocity and travel distance of the debris, according to changes in the internal friction angle, indicated that the debris was affected by the environment.     

Influences of different crossing types on dynamic response of underground cavern subjected to ground shock

An intersecting cavern is a common structural form used in underground engineering, and its safety and stability performance directly control the service performance of the whole project. The dynamic re-sponses of the three kinds of crossing type (+-shaped, T-shaped, L-shaped) caverns subjected to ground shock were studied by numerical simulation. The velocity plus force mode boundary setting method was proposed in the coupled static and dynamic analysis of a deep underground cavern. The results show that, among the three types of crossing caverns, the+-shaped cavern is the most significantly affected by the dynamic action, followed by T-shaped, and then L-shaped caverns. The vault settlement, straight wall deformation, vault peak particle velocity, effective plastic strain of surrounding rock, and maximum principal stress and strain at the bottom of the lining of the straight wall increase with the increase of cavern span. The vault settlement, straight wall deformation, effective plastic strain of surrounding rock, and the maximum principal stress and strain at the bottom of lining to the straight wall decrease with the increase of lateral pressure coefficient, and the peak particle velocity at the vault increases. The variation is small compared with the change of cavern span. The influence range of the underground cavern intersection is two cavern diameters from the intersection centre. The bottom of the straight wall at the intersection is the weak part. It is suggested to thicken the support locally to improve the stability of the cavern.     

防空武器火控系统对空中目标参数估计方法仿真

针对防空武器火控系统的特点,提出了一种防空武器火控系统对空中目标参数估计的方法,可以在不知道目标距离的条件下得到目标的航向角与俯仰角,实现对目标的被动式跟踪,对估计误差的统计特性进行了分析,仿真结果表明了该方法比传统的估计方法更加可行.     

3D laser scanning strategy based on cascaded deep neural network

A 3D laser scanning strategy based on cascaded deep neural network is proposed for the scanning system converted from 2D Lidar with a pitching motion device. The strategy is aimed at moving target detection and monitoring. Combining the device characteristics, the strategy first proposes a cascaded deep neural network, which inputs 2D point cloud, color image and pitching angle. The outputs are target distance and speed classification. And the cross-entropy loss function of network is modified by using focal loss and uniform distribution to improve the recognition accuracy. Then a pitching range and speed model are proposed to determine pitching motion parameters. Finally, the adaptive scanning is realized by integral separate speed PID. The experimental results show that the accuracies of the improved network target detection box, distance and speed classification are 90.17%, 96.87% and 96.97%, respectively. The average speed error of the improved PID is 0.4239°/s, and the average strategy execution time is 0.1521 s. The range and speed model can effectively reduce the collection of useless information and the deformation of the target point cloud. Conclusively, the experimental of overall scanning strategy show that it can improve target point cloud integrity and density while ensuring the capture of target.     

舰艇姿态对雷达测量误差的影响分析

为了研究舰艇姿态对雷达测量误差的影响,分析了雷达测量过程中引入舰艇姿态误差的机理.。采用对误差传递过程进行建模的方法,建立了包含舰艇姿态因素的雷达测量误差模型。通过该模型分析了舰艇姿态角误差对雷达测量目标距离、方位角和高低角误差的不同影响,得出雷达测距误差不受姿态角误差影响,方位角误差与艏向角误差呈线性关系,高低角误差受纵摇角与横摇角误差影响,并随目标方位按正弦规律变化的结论。计算机仿真结果验证了结论的正确性。