A quasi-isentropic model of a cylinder driven by aluminized explosives based on characteristic line analysis

A quasi-isentropic study on the process of driving a cylinder with aluminized explosives was carried out to examine the influence of the aluminum (Al) reaction rate on cylinder expansion and the physical parameters of the detonation products. Based on the proposed quasi-isentropic hypothesis and relevant isentropic theories, the characteristic lines of aluminized explosives driving a cylinder were analyzed, and a quasi-isentropic model was established. This model includes the variation of the cylinder wall velocity and the physical parameters of the detonation products with the Al reaction degree. Using previously reported experimental results, the quasi-isentropic model was verified to be applicative and accurate. This model was used to calculate the physical parameters for cylinder experiments with aluminized cyclotrimethylenetrinitramine explosives with 15.0 % and 30.0 % Al content. The results show that this quasi-isentropic model can be used not only to calculate the cylinder expansion rule or Al reaction degree, but also to calculate the physical parameters of the detonation products in the process of cylinder expansion. For explosives with 15.0 % and 30.0 % Al, 24.3 % and 18.5 % of the Al was found to have reacted at 33.9 μs and 34.0 μs, respectively. The difference in Al content results in different reaction intensity, occurrence time, and duration of two forms of reaction (diffusion and kinetic) between the Al powder and the detonation products; the post-detonation burning reaction between the Al powder and the detonation products prolongs the positive pressure action time, resulting in a continuous rise in temperature after detonation.     

A study on the surface overpressure distribution and formation of a double curvature liner under a two-point initiation

The formation mechanism of an EFP(explosively formed projectile) using a double curvature liner under the overpressure effect generated by a regular oblique reflection was investigated in this paper.Based on the detonation wave propagation theory,the change of the incident angle of the detonation wave collision at different positions and the distribution area of the overpressure on the surface of the liner were calculated.Three-dimensional numerical simulations of the formation process of the EFP with tail as well as the ability to penetrate 45# steel were performed using LS-DYNA software,and the EFP ve-locity,the penetration ability,and the forming were assessed via experiments and x-ray photographs.The experimental results coincides with those of the simulations.Results indicate that the collision of the detonation wave was controlled to be a regular oblique reflection acting on the liner by setting the di-mensions of the unit charge and maintaining the pressure at the collision point region at more than 2.4 times the CJ detonation when the incident angle approached the critical angle.The distance from the liner midline to the boundary of the area within which the pressure ratio of the regular oblique reflection pressure to the CJ detonation pressure was greater than 2.5,2,and 1.5was approximately 0.66 mm,1.32 mm,and 3.3 mm,respectively.It is noted that pressure gradient caused the liner to turn inside out in the middle to form the head of the EFP and close the two tails of the EFP at approximately 120μs.The penetration depth of the EFP into a 45# steel target exceeded 30 mm,and there was radial expansion between the head and tail of the EFE increasing the penetration resistance of the EFP.Therefore,the structural size of the unit charge and the liner can be further optimized to reduce resistance to increase the penetration ability of the EFP.     

科学管理、精益管理与精确作战工程保障研究

设计是作战行动筹划的重要步骤,精确工程保障需要对工程保障行动进行精密的设计和精确管理与控制。科学管理采用科学实验的方法,通过劳动方法标准化和差别计件工资制度,有效提高了工作效率,其基本原理经过百余年的实际检验,被证明是一个成熟有效的管理方法。借鉴科学管理理论,需要对工程保障行动进行动作研究,进而研究工程保障行动的作业标准,以期提高其保障效率。精益管理是在科学管理在新的历史时期的发展与改进,它使用了准时制、零库存、均衡生产、持续改进等先进的管理理念和六西格玛管理、成组技术等先进技术,为基于信息系统体系作战的工程保障能力生成提供了有益的借鉴,可加深我们对精确工程保障的理解,促进精确工程保障研究的可操作性。     

飞机电磁弹射系统发展及其关键技术

总结论述了美国和英法国家的飞机电磁弹系统工程化应用研制的发展状况,综述了电磁弹射用直线电机的方案选型设计、仿真技术、性能优化和控制方法等方面的关键技术和研究现状,针对电磁弹射技术的发展前景和应用给出了相关建议,为国内电磁弹射相关技术的发展提供了借鉴。     

Influence of Al2O3 particles on the microstructure and mechanical properties of copper surface composites fabricated by friction stir processing

The influence of three factors, such as volume percentage of reinforcement particles (i.e. Al₂O₃), tool tilt angle and concave angle of shoulder, on the mechanical properties of Cu–Al₂O₃ surface composites fabricated via friction stir processing was studied. Taguchi method was used to optimize these factors for maximizing the mechanical properties of surface composites. The fabricated surface composites were examined by optical microscope for dispersion of reinforcement particles. It was found that Al₂O₃ particles are uniformly dispersed in the stir zone. The tensile properties of the surface composites increased with the increase in the volume percentage of the Al₂O₃ reinforcement particles. This is due to the addition of the reinforcement particles which increases the temperature of recrystallization by pinning the grain boundaries of the copper matrix and blocking the movement of the dislocations. The observed mechanical properties are correlated with microstructure and fracture features.     

逆变器-异步电机电磁噪声的分析与研究

利用Ansoft建立了样机的二维模型,计算了样机在空载运行下的各性能参数,分析了样机内的磁场分布情况.在此基础上,计算了负载大小、机壳设计尺寸和逆变器供电对异步电机电磁噪声的影响.仿真分析表明:通过合理改变机壳尺寸和质量以及选择合适的逆变器开关频率的方法可实现异步电机的降噪.     

Initiating insurgencies abroad: French plans to ‘chouannise’ Britain and Ireland, 1793–1798

Secret French plans to launch guerrilla-style raids on the British Isles devised in the spring of 1796 were referred to as ‘chouanneries’. The name and concept behind these small-war operations were modelled on the irregular tactics used by the Chouan rebels in the Vendée, which the French state army had brutally quashed, but some wished to transfer into their institutional practice. Part of France's ongoing military strategy in the war against Britain, which included fomenting insurrection in Ireland, these irregular operations were to be manned partially by pardoned deserters and released convicts and prisoners of war. Of these, only Tate's brief invasion of Wales in 1797 was realised, but the surviving plans provide insightful historical lessons into an Anglophobic mindset shared by a small network of practitioners and policy deciders on the effectiveness of such shock and awe tactics. Largely motivated by the desire to take revenge for Britain's support of counter-revolutionaries in the Vendée, these plans could more aptly be referred to as counter-‘chouanneries’.     

碳纤维强度的统计特性及对复合材料线芯力学性能的影响

测试了国产T300级碳纤维的单丝和复丝拉伸强度,并用Weibull分布来描述碳纤维单丝平均拉伸强度。采用拉挤工艺制备出国产碳纤维复合线芯,测试了国产碳纤维复合线芯的弯曲强度和短梁剪切强度性能。结果表明:国产T300级碳纤维单丝拉伸强度性能达到东丽T300碳纤维水平,且分散性更小;复丝强度略低。国产T300级碳纤维集束性较差,在拉挤抽纱过程中,容易夹纱和起毛。在纤维体积含量基本相同情况下,国产T300级碳纤维复合线芯力学性能与东丽T700碳纤维复合线芯力学性能相差不大。     

非相干背景光辐照二波耦合中的最佳匹配随机共振

针对非相干背景光辐照二波耦合中参数的最佳匹配设计问题,提出了一种基于随机共振理论的研究方法。首先,文章通过二波耦合过程进行物理机理分析和数值实验分析,证明了该问题在本质上可归结为一种随机共振现象。其次,从随机共振的角度,研究其中的最佳参数设计问题,给出了一种分布处理的最优参数设计流程。按照该方法,在给定增益要求的情况下,先根据信号光饱和与否来确定晶体长度,最后根据非相干光的比例对增益的影响来确定非相干光的比例。仿真实验表明,经过最佳参数设计后,信号的增益和输出信噪比上均有显著提高。     

Assessing the value of demand sharing in supply chains

We consider the problem of assessing the value of demand sharing in a multistage supply chain in which the retailer observes stationary autoregressive moving average demand with Gaussian white noise (shocks). Similar to previous research, we assume each supply chain player constructs its best linear forecast of the leadtime demand and uses it to determine the order quantity via a periodic review myopic order‐up‐to policy. We demonstrate how a typical supply chain player can determine the extent of its available information in the presence of demand sharing by studying the properties of the moving average polynomials of adjacent supply chain players. The retailer's demand is driven by the random shocks appearing in the autoregressive moving average representation for its demand. Under the assumptions we will make in this article, to the retailer, knowing the shock information is equivalent to knowing the demand process (assuming that the model parameters are also known). Thus (in the event of sharing) the retailer's demand sequence and shock sequence would contain the same information to the retailer's supplier. We will show that, once we consider the dynamics of demand propagation further up the chain, it may be that a player's demand and shock sequences will contain different levels of information for an upstream player. Hence, we study how a player can determine its available information under demand sharing, and use this information to forecast leadtime demand. We characterize the value of demand sharing for a typical supply chain player. Furthermore, we show conditions under which (i) it is equivalent to no sharing, (ii) it is equivalent to full information shock sharing, and (iii) it is intermediate in value to the two previously described arrangements. Although it follows from existing literature that demand sharing is equivalent to full information shock sharing between a retailer and supplier, we demonstrate and characterize when this result does not generalize to upstream supply chain players. We then show that demand propagates through a supply chain where any player may share nothing, its demand, or its full information shocks (FIS) with an adjacent upstream player as quasi‐ARMA in—quasi‐ARMA out. We also provide a convenient form for the propagation of demand in a supply chain that will lend itself to future research applications. © 2014 Wiley Periodicals, Inc. Naval Research Logistics 61: 515–531, 2014