Fabrication of AA7005/TiB2-B4C surface composite by friction stir processing: Evaluation of ballistic behaviour

The present work aims to enhance the ballistic resistance of AA7005 alloy by incorporating the TiB₂ and B₄C ceramic reinforcement particles. Surface composites with different weight fractions of TiB₂ and B₄C particles were processed by friction stir processing. Micro-hardness and depth of penetration tests were carried out to evaluate the ballistic properties of the surface composites. The surface hardness of the composite was found to be nearly 70 HV higher than base alloy. The depth of penetration of the steel projectile was 20–26 mm in the composites as compared to 37 mm in the base alloy. Ballistic mass efficiency factor of the surface composite was found to be 1.6 times higher than base alloy. This is mainly attributed to the dispersion strengthening from the reinforcement particles.     

添加SiC微粉对硅树脂先驱体转化3D Cf/Si-O-C材料性能的影响

以三维碳纤维织物和廉价的硅树脂为原料,采用先驱体转化工艺制备3D G/Si-O-C材料,考察了浸渍液中添加SiC填料对材料微观结构、力学性能和抗氧化性能影响.结果表明:添加适量的SiC填料有助于减少基体孔隙,改善界面结合,从而提高材料的力学性能;而SiC含量过高时,容易在材料内部形成闭孔,从而导致材料力学性能下降.当SiC微粉含量为18.2%时,材料具有最好的力学性能,弯曲强度和断裂韧度分别为421.3MPa和13.0 MPa·m1/2;而材料的抗氧化性能随着SiC微粉含量的增加而增加,当SiC微粉含量为25.0%时,材料的弯曲强度保留率最高,达到了89.5%.     

Effect of nano powder (Al2O3-CaO) addition on the mechanical properties of the polymer blend matrix composite

This work describes the preparation and study of the properties of composite nanoparticles prepared by the sol-gel method which consists of two materials (Al₂O₃-CaO), and study the effect of these nanoparticles on the mechanical behavior of a polymer blend (EP 4% + 96% UPE). The powder was evaluated by X-ray diffraction analysis, scanning electron microscopy analysis (SEM), particle size analysis, and energy dispersive X-ray analysis (EDX). The mechanical behavior of the composite material was assessed by tensile test, bending test and hardness test. The evaluation results of the composite nanoparticles showed good distribution of the chemical composition between aluminum oxide and calcium oxide, smoothness in particles' size at calcination in high and low temperatures, formation of different shapes of nanoparticles and different (kappa and gamma) phases of the Al₂O₃ particles. The results of mechanical behavior tests showed marked improvement in the mechanical properties of the resulted composite material, especially at 1.5%, compared with polymer blend material without nano powder addition. The tensile properties improved about (24 and 14.9) % and bending resistance about (23.5 and 16.8) % and hardness by (25 and 22) % when adding particles of size (63.8 and 68.6) respectively. Therefore, this reflects the efficiency of the proposed method to manufacture the nanocomposite powder and the possibility of using this powder as a strengthening material for the composite materials and using these composite materials in bio applications, especially in the fabrication of artificial limbs.     

Enhancement of wear and ballistic resistance of armour grade AA7075 aluminium alloy using friction stir processing

Industrial applications of aluminium and its alloys are restricted because of their poor tribological properties. Thermal spraying, laser surfacing, electron beam welding are the most widely used techniques to alter the surface morphology of base metal. Preliminary studies reveal that the coating and layering of aluminium alloys with ceramic particles enhance the ballistic resistance. Furthermore, among aluminium alloys,7075 aluminium alloy exhibits high strength which can be compared to that of steels and has profound applications in the designing of lightweight fortification structures and integrated protection systems. Having limitations such as poor bond integrity, formation of detrimental phases and interfacial reaction between reinforcement and substrate using fusion route to deposit hard particles paves the way to adopt friction stir processing for fabricating surface composites using different sizes of boron carbide particles as reinforcement on armour grade 7075 aluminium alloy as matrix in the present investigation. Wear and ballistic tests were carried out to assess the performance of friction stir processed AA7075 alloy. Significant improvement in wear resistance of friction stir processed surface composites is attributed to the change in wear mechanism from abrasion to adhesion. It has also been observed that the surface metal matrix composites have shown better ballistic resistance compared to the substrate AA7075 alloy. Addition of solid lubricant Mo S2 has reduced the depth of penetration of the projectile to half that of base metal AA7075 alloy. For the first time, the friction stir processing technique was successfully used to improve the wear and ballistic resistances of armour grade high strength AA7075 alloy.     

Tuning the reactivity of Al–Ni by fine coating of halogen-containing energetic composites

In this paper, various core-shell structured Al–Ni@ECs composites have been prepared by a spray-drying technique. The involved ECs refer to the energetic composites (ECs) of ammonium perchlorate/nitrocellulose (AP/NC, NA) and polyvinylidene fluoride/hexanitrohexaazaisowurtzitane (PVDF/CL-20, PC). Two Al–Ni mixtures were prepared at atomic ratios of 1:1 and 1:3 and named as Al/Ni and Al/3Ni, respectively. The thermal reactivity and combustion behaviors of Al–Ni@ECs composites have been comprehensively investigated. Results showed that the reactivity and combustion performance of Al–Ni could be enhanced by introducing both NA and PC energetic composites. Among which the Al/Ni@NA composite exhibited higher reactivity and improved combustion performance. The measured flame propagation rate (v = 20.6 mm/s), average combustion wave temperature (T_max = 1567.0 °C) and maximum temperature rise rate (γ_t = 1633.6 °C/s) of Al/Ni@NA are higher than that of the Al/Ni (v = 15.8 mm/s, T_max = 858.0 °C, and γ_t = 143.5 °C/s). The enhancement in combustion properties could be due to presence of the acidic gaseous products from ECs, which could etch the Al₂O₃ shell on the surface of Al particles, and make the inner active Al to be easier transported, so that an intimate and faster intermetallic reaction between Al and Ni would be realized. Furthermore, the morphologies and chemical compositions of the condensed combustion products (CCPs) of Al–Ni@ECs composites were found to be different depending on the types of ECs. The compositions of CCPs are dominated with the Al–Ni intermetallics, combining with a trace amount of Al₅O₆N and Al₂O₃.     

The mechanical performance and a rate-dependent constitutive model for Al3Ti compound

The Al₃Ti compound has potential application in the high temperature structure materials due to its low density, high strength and stiffness. The mechanical behaviors of the material under different loading rates were studied using compression tests. The results indicate that Al₃Ti is a typical brittle material and its compressive strength is dependent on the strain rate. Therefore, a series of rate-dependent constitutive equations are needed to describe its mechanical behaviors accurately. However, it is still short of professional research on the material model for Al₃Ti. In this study, the material model was developed on the basis of JH-2 constitutive equations using the experimental data. The model was then applied in simulating the impact process of Ti/Al₃Ti metal-intermetallic laminate composites so as to validate the established model. Good agreement between simulation and experiment results shows the constitutive model predict the material responses under high rate and large deformation accurately. This work provides more support for the theoretical and numerical research on the intermetallic.     

列车用复合材料阻燃性能研究

不同类别的阻燃剂配合使用能产生协效作用,大大提高阻燃效果。在甲基丙烯酸类不饱和聚酯树脂9001基体中,添加微囊化红磷/氢氧化铝/三氧化二锑/甲基膦酸二甲酯(MRP/Al(OH)3/Sb2O3/DMMP)阻燃剂体系,对其树脂体系固化物及玻璃纤维织物复合材料的力学性能和阻燃性能进行了实验研究,提出了一种有望用于列车复合材料大尺寸构件制造的性能优异、价格低廉的新体系。结果表明,当质量添加比例分别为12%MRP、50%Al(OH)3、2%Sb2O3时,树脂体系室温粘度100mPa.s左右,凝胶时间超过80min,适用于RTM和VIMP等大尺寸构件成型工艺;复合材料拉伸强度215.4MPa,弯曲强度177.15MPa,拉伸模量13.85GPa,弯曲模量13.36GPa,氧指数39.7。     

Investigating the surface integrity of aluminium based composites machined by EDM

In the present work, the surface characteristics of Electrical Discharge Machined (EDM) Al (6351)SiC and Al (6351)SiCB₄C composites are investigated. The composites are prepared by employing the conventional stir casting technique, as it can produce better particle dispersion in the matrix. The detailed experimental study is performed on the composites by varying current (I), duty factor (τ), pulse on time (T_on), and the gap voltage (V) in order to analyze the Heat Affected Zone (HAZ) formed in the sub surface and the average crater diameter formed on the machined surface of the composites as an output function. The formation of recast layers, presence of bubbles and the surface texture of the composites at various machining conditions are observed. The results show that the increased Metal Removal Rate (MRR) increases the depth of HAZ and the average crater diameter on the machined area. Further, the addition of B₄C particles to the composite produces more surface defect than the AlSiC composite.     

Synergistic effect of hybrid Himalayan Nettle/Bauhinia-vahlii fibers on physico-mechanical and sliding wear properties of epoxy composites

The cellulosic bast fibers are recognized as a justifiable and biodegradable substitute for producing moderate strength polymer composite materials because of their characteristics of renewability, eco-friendliness, and higher specific strength. Hence the aim of this research work is to fabricate Himalayan bast fibers (Nettle fiber (NF)/bauhinia vahlii fiber (BF)) based mono/hybrid epoxy composites at varying weight percentage of 2–6 wt% and evaluate the physical (void fraction and water absorption), mechanical (tensile strength, flexural strength, hardness) and sliding wear properties of as-fabricated composites. The 6 wt% NBF reinforced composites exhibited higher mechanical properties as compared to NF and BF composites with tensile strength of 34.04 MPa, flexural strength of 42.45 MPa, and hardness of 37.01 H_v respectively. The influence of various control factors (sliding velocity, NF/BF/NBF contents, normal load and sliding distance) on specific sliding wear rate of composites was evaluated by Taguchi (three factors at three levels) experimental design and the percentage contribution of these selected parameters on sliding wear performance was examined by Analysis of variance (ANOVA). The sliding wear property of as-developed composites was found to be greatly influenced by sliding velocity and the wear resistance was observed to be improved with the NF/BF/NBF contents. The wear mechanism of the as-fabricated composites has been elucidated by scanning electron microscopy analysis. The research outcomes demonstrated that the hybridization of Bauhinia vahlii fiber with Nettle fiber led to improve the mechanical and wear properties of epoxy composites.     

Optimization of process parameters of aluminum alloy AA 2014-T6 friction stir welds by response surface methodology

The heat treatable aluminum-copper alloy AA2014 finds wide application in the aerospace and defence industry due to its high strength-toweight ratio and good ductility. Friction stir welding(FSW) process, an emerging solid state joining process, is suitable for joining this alloy compared to fusion welding processes. This work presents the formulation of a mathematical model with process parameters and tool geometry to predict the responses of friction stir welds of AA 2014-T6 aluminum alloy, viz yield strength, tensile strength and ductility. The most influential process parameters considered are spindle speed, welding speed, tilt angle and tool pin profile. A four-factor, five-level central composite design was used and a response surface methodology(RSM) was employed to develop the regression models to predict the responses.The mechanical properties, such as yield strength(YS), ultimate tensile strength(UTS) and percentage elongation(%El), are considered as responses. Method of analysis of variance was used to determine the important process parameters that affect the responses. Validation trials were carried out to validate these results. These results indicate that the friction stir welds of AA 2014-T6 aluminum alloy welded with hexagonal tool pin profile have the highest tensile strength and elongation, whereas the joints fabricated with conical tool pin profile have the lowest tensile strength and elongation.     

烧结助剂对碳纳米管增强氮化铝陶瓷结构与性能的影响

采用热压烧结工艺制备了碳纳米管增强氮化铝陶瓷,研究了烧结助剂种类、含量对碳纳米管增强氮化铝陶瓷性能及结构的影响.利用XRD、SEM和TEM等分析测试手段对其相组成,断口形貌和微观结构进行了分析.结果表明,烧结助剂Y2O3+CaF2较YE3+CaF2更能促进碳纳米管增强氮化铝陶瓷致密化,但随烧结助剂Y2O3+CaF2含量的增加,碳纳米管增强氮化铝陶瓷致密度提高,而力学、导热性能下降.     

Influence of yttrium on microstructure and properties of Ni–Al alloy coatings prepared by laser cladding

Ni–Al alloy coatings with different Y additions are prepared on 45^# medium steel by laser cladding. The influence of Y contents on the microstructure and properties of Ni–Al alloy coatings is investigated using X-ray diffraction, scanning electron microscopy, electron probe microanalyzer, Vickers hardness tester, friction wear testing machine, and thermal analyzer. The results show that the cladding layers are mainly composed of NiAl dendrites, and the dendrites are gradually refined with the increase in Y additions. The purification effect of Y can effectively prevent Al₂O₃ oxide from forming. However, when the atomic percent of Y addition exceeds 1.5%, the extra Y addition will react with O to form Y₂O₃ oxide, even to form Al₅Y₃O₁₂ oxide, depending on the amount of Y added. The Y addition in a range of 1.5–3.5 at.% reduces the hardness and anti-attrition of cladding layer, but improves obviously its wear and oxidation resistances.     

纤维增强SiO2气凝胶隔热复合材料的制备及其性能

将无机陶瓷纤维与SiO2溶胶混合,经超临界干燥制备了SiO2气凝胶隔热复合材料。SiO2气凝胶纤细的骨架颗粒减少了固态热传导,纳米级孔减少了气体热传导和对流传热,同时无机陶瓷纤维减少了辐射传热。SiO2气凝胶复合材料具有良好的隔热性能,其200℃和800℃的热导率分别为0.017W/m.K和0.042W/m.K。纤维的加入提供了力学支撑,高温处理增强了气凝胶骨架强度,材料在常温和高温下均具有良好的力学性能,其常温的拉伸、弯曲和抗压强度分别为1.44MPa、1.31MPa和0.98MPa(10%应变),800℃的拉伸、弯曲和抗压强度分别为1.95MPa、1.80MPa和1.42MPa(10%应变)。     

Insensitive energetic microspheres DAAF/RDX fabricated by facile molecular self-assembly

Insensitive energetic materials are promising in the defense weapons field. However, energetic materials still suffer from great challenges and the concern about their safety limits their utilization. In this work, insensitive energetic explosive 3,3′-diamino-4,4′-azoxyfurazan/hexahydro-1,3,5-trinitro-1,3,5-triazine (DAAF/RDX) microspheres were fabricated by self-assembly method. Rod-like DAAF/RDX was prepared by mechanical ball milling for comparison. DAAF/RDX composites with different mass ratios (90:10, 80:20, and 70:30) were obtained. The morphologies and structures of as-obtained DAAF/RDX composites were characterized by scanning electron microscopy (SEM), powder x-ray diffraction (PXRD) and fourier transform infrared spectroscopy (FT-IR). The results showed that DAAF/RDX microspheres exhibited regular shaped microspheres with sizes from 0.5 to 1.2 μm. There was no crystal transition during the modification process. The thermal properties of as-obtained materials were then evaluated by differential scanning calorimetry (DSC) and materials studio software. DAAF/RDX microspheres showed an advanced decomposition peak temperature compared with rod-like DAAF/RDX. The binding energy and peak temperature values at zero β_i (T_P0) of DAAF/RDX (90:10) increased by 36.77 kJ/mol, 1.6 °C, and 58.11 kJ/mol, 12.3 °C compared to DAAF/RDX (80:20) and DAAF/RDX (70:30), indicating the better thermal stability of DAAF/RDX (90:10). The characteristic drop height (H₅₀) of DAAF/RDX (higher than 100 cm) composites was higher than that of raw RDX (25 cm), suggesting significant improvements in mechanical safety. The preparation of DAAF/RDX microspheres is promising for the desensitization of RDX and useful for the formation of other materials and future wide applications.     

用溶胶-凝胶法制备碳纤维三维编织物增强氧化铝基复合材料的研究

本文研究了溶胶－凝胶（Ｓｏｌ－ｇｅｌ）法制备碳纤维三维编织物增强氧化铝（Ａｌ２Ｏ３）基复合材料的成型工艺及其力学性能，研究了两种主要起始物Ａｌ（ＮＯ３）３、ＡｌＣｌ３配制的氧化铝溶胶对复合材料成型工艺和力学性能的影响。分别以Ａｌ（ＮＯ３）３和ＡｌＣｌ３为起始物，制备得到Ⅰ＃、Ｉ＃复合材料。研究表明，以Ａｌ（ＮＯ３）３为起始物配制的溶胶粘度较小，利于材料的致密化。经过溶胶浸渍、凝胶、裂解１３个周期后，Ⅰ＃材料的密度和室温三点弯曲强度分别为１．８６ｇ／ｃｍ３和１４５．２ＭＰａ，而ＩＩ＃材料的密度和室温三点弯曲强度分别为１．６３ｇ／ｃｍ３和１０４．１ＭＰａ，材料均呈典型的韧性断裂模式。用扫描电子显微镜（ＳＥＭ）观察试样的断口形貌，发现断口表面有大量的纤维拔出，纤维表现了较好的增韧效果。     

表面官能化对碳纳米管/环氧复合材料玻璃化转变温度及韧性的影响

通过碳纳米管的不同表面官能化,构造其与环氧树脂的不同界面。采用动态机械性能分析研究不同表面官能化碳纳米管对环氧树脂复合材料玻璃化转变温度的影响;采用摆锤冲击试验研究环氧树脂复合材料的韧性。结果表明:与纯环氧树脂相比,氨基化碳纳米管/环氧树脂复合材料的玻璃化转变温度升高,而羧基化碳纳米管/环氧树脂复合材料的玻璃化转变温度反而有所下降;碳纳米管/环氧树脂复合材料的冲击强度相比纯环氧树脂均提高了近一倍。复合材料性能的这些变化规律主要归因于不同表面官能化碳纳米管与环氧树脂基体间形成了不同的界面。     

Effect of organo-modified montmorillonite nanoclay on mechanical,thermal and ablation behavior of carbon fiber/phenolic resin composites

The mechanical, thermal and ablation properties of carbon phenolic (C-Ph) composites (Type-I) rein-forced with different weight percentages of organo-modified montmorillonite (o-MMT) nanoclay have been studied experimentally. Ball milling was used to disperse different weight (wt) percentages (0, 1,2,4,6 wt.％) of nanoclay into phenolic resin. Viscosity changes to resin due to nanoclay was studied. On the other hand, nanoclay added phenolic matrix composites (Type-II) were prepared to study the dispersion of nanoclay in phenolic matrix by small angle X-ray scattering and thermal stability changes to the matrix by thermogravimetric analyser (TGA). This data was used to understand the mechanical, thermal and ablation properties of Type-I composites. Inter laminar shear strength (ILSS), flexural strength and flexural modulus of Type I composites increased by about 29％, 12％and 7％respectively at 2 wt.％ addition of nanoclay beyond which these properties decreased. This was attributed to reduced fiber volume fraction (％Vf) of Type-I composites due to nanoclay addition at such high loadings. Mass ablation rate of Type-I composites was evaluated using oxy acetylene torch test at low heat flux (125 W/cm2) and high heat flux levels (500 W/cm2). Mass ablation rates have increased at both flux levels marginally up to 2 wt.％ addition of nanoclay beyond which it has increased significantly. This is in contrast to increased thermal stability observed for Type-I and Type-Ⅱ composites up to 2 wt.％addition of nanoclay. Increased ablation rates due to nanoclay addition was attributed to higher insulation effi-ciency of nanolcay, which accumulates more heat energy in limited area behind the ablation front and self-propagating ablation mechanisms triggered by thermal decomposition of organic part of nanoclay.     

Multifunctional A356 alloy/ PKSAnp composites: Microstructure and mechanical properties

Mechanical properties and microstructure of multifunctional composites produced with palm kernel shell ash nanoparticle (PKSAnp)-A356 alloy composites was studied. The composites were produced using Double layer feeding stir casting method (DLF-SCM) by adding 1 wt%‒4 wt.% PKSAnp. The microstructure, density, electrical and mechanical properties were determined. The results shows that there was a uniform distribution of the PKSAnp in A356 alloy. The mismatch at the interface between the PKSAnp and A356 alloy was 4.26%. Improvement of 30.47%, 41.91%, 49.52%, 40.90% and 65.09% were obtained for hardness values, tensile, yield strength, %elongation and impact energy at 4 wt% PKASnp. The work has established that the developed composites can be used for multifunctional applications where combination of toughness and strength is vital.     

Consequence of reinforced SiC particles and post process artificial ageing on microstructure and mechanical properties of friction stir processed AA7075

Friction stir processing and post process artificial ageing was successfully carried out on AA7075 with and without reinforcement of SiC particles producing defect free processed zone with uniform distribution of filler material. Effect of SiC particle reinforcement and artificial ageing times on the microstructural modifications was characterized using optical and electron microscopy, electron backscattered diffraction and X-Ray diffraction. Hardness, impact and wear tests were carried out to investigate mechanical behaviour before and after processing. Reinforcement of SiC particles during FSP and subsequent age hardening treatment brought about nearly twofold increase in hardness and impact toughness values by the combined effect of grain refinement, Zener pinning, dispersion strengthening and precipitation hardening. Significant improvement in wear resistance in terms of wear loss was also observed after processing compared to the reference material AA7075-T6. Fractured surface of post FSP age hardened AA7075 alloy exhibited features of ductile fracture during Charpy impact test.     

Effect of tool rotational speed on the particle distribution in friction stir welding of AA6092/17.5 SiCp-T6 composite plates and its consequences on the mechanical property of the joint

This study investigates the effect of tool rotational speed (TRS) on particle distribution in nugget zone (NZ) through quantitative approach and its consequences on the mechanical property of friction stir welded joints of AA6092/17.5 SiC_p-T6 composite. 6 mm thick plates are welded at a constant tool tilt angle of 2° and tool traverse speed of 1 mm/s by varying the TRS at 1000 rpm, 1500 rpm and 2000 rpm with a taper pin profiled tool. Microstructure analysis shows large quantity of uniformly shaped smaller size SiC particle with lower average particle area which are homogeneously distributed in the NZ. The fragmentation of bigger size particles has been observed because of abrading action of the hard tool and resulting shearing effect and severe stress generation due to the rotation of tool. The particles occupy maximum area in the matrix compared to that of the base material (BM) due to the redistribution of broken particles as an effect of TRS. The migration of particles towards the TMAZ-NZ transition zone has been also encountered at higher TRS (2000 rpm). The microhardness analysis depicts variation in average hardness from top to bottom of the NZ, minimum for 1500 rpm and maximum for 2000 rpm. The impact strength at 1000 rpm and 1500 rpm remains close to that of BM (21.6 J) while 2000 rpm shows the accountable reduction. The maximum joint efficiency has been achieved at 1500 rpm (84%) and minimum at 1000 rpm (68%) under tensile loading. Fractographic analysis shows mixed mode of failure for BM, 1000 rpm and 1500 rpm, whereas 2000 rpm shows the brittle mode of failure.