预处理方法在全速度流场数值模拟中的应用

基于预处理方法,采用有限差分方法,LU-SGS隐式求解了二维可压Navier-Stokes方程,数值模拟了无粘突包、粘性空腔、化学非平衡流场,并与试验结果进行了对比。计算结果表明,所采用的数值模拟方法能够求解低速及亚、跨、超全速度流场和化学非平衡流场,所采用的预处理方法在亚声速范围内保持数值精度的前提下,加速了收敛。     

燃烧对固体燃料冲压发动机附着点的影响

应用 PHOENICS软件模拟了固体燃料冲压发动机 ( SFRJ)的冷流和以 HTPB、PS为推进剂的简单反应流。结果表明 :在相同入口条件下 ,燃烧使附着点明显前移 ,从而改变了流场结构 ;入口温度不影响冷流时的附着点 ,但在有反应情况下则有一定影响 ;在两种情况下入口流量对附着点均无影响。     

Development of multi-physics numerical simulation model to investigate thermo-mechanical fatigue crack propagation in an autofrettaged gun barrel

In this research, a detailed multi-physics study has been carried out by numerically simulating a solid fractured gun barrel for 20 thermo-mechanical cycles. The numerical model is based on thermal effects, mechanical stress fields and fatigue crack mechanics. Elastic-plastic material data of modified AISI 4340 at temperatures ranging from 25 to 1200 °C and at strain rates of 4, 16, 32 and 48 s⁻¹ was acquired from high-temperature compression tests. This was used as material property data in the simulation model. The boundary conditions applied are kept similar to the working gun barrel during continuous firing. A methodology has been provided to define thermo-mechanically active surface-to-surface type interface between the crack faces for a better approximation of stresses at the crack tip. Comparison of results from non-autofrettaged and autofrettaged simulation models provide useful information about the evolution of strains and stresses in the barrel at different points under combined thermo-mechanical loading cycles in both cases. The effect of thermal fatigue under already induced compressive yield due to autofrettage and the progressive degradation of the accumulated stresses due to thermo-mechanical cyclic loads on the internal surface of the gun barrel (mimicking the continuous firing scenario) has been analyzed. Comparison between energy release rate at tips of varying crack lengths due to cyclic thermo-mechanical loading in the non-autofrettaged and autofrettaged gun has been carried out.     

Numerical studies on four-engine rocket exhaust plume impinging on flame deflectors with afterburning

This paper studies the four-engine liquid rocket flow field during the launching phase. Using three-dimensional compressible Navier-Stokes equations and two-equation realizable k-epsilon turbulence model, an impact model is established and flow fields of plume impinging on the two different shapes of flame deflectors, including wedge-shaped flame deflector and cone-shaped flame deflector, are calcu-lated. The finite-rate chemical kinetics is used to track chemical reactions. The simulation results show that afterburning mainly occurs in the mixed layer. And the region of peak pressure occurs directly under the rocket nozzle, which is the result of the direct impact of exhaust plume. Compared with the wedge-shaped flame deflector, the cone-shaped flame deflector has great performance on guiding exhaust gas. The wedge-shaped and cone-shaped flame deflectors guide the supersonic exhaust plume away from the impingement point with two directions and circumferential direction, respectively. The maximum pressure and temperature on the wedge-shaped flame deflector surface are 37.2% and 9.9% higher than those for the cone-shaped flame deflector. The results provide engineering guidance and theoretical significance for design in flame deflector of the launch platforms.     

Damage to aircraft composite structures caused by directed energy system: A literature review

This paper presents a comprehensive review of the research studies on direct energy system effect on aircraft composite structures to develop a good understanding of state-of-the-art research and devel-opment in this area. The review begins with the application of composite materials in the aircraft structures and highlights their particular areas of application and limitations. An overview of directed energy system is given. Some of the commonly used systems in this category are discussed and the working principles of laser energy systems are described. The experimental and numerical studies re-ported regarding the aircraft composite structures subject to the effect of directed energy systems, especially the laser systems are reviewed in detail. In particularly, the general effects of laser systems and the relevant damage mechanisms against the composite structures are reported. The review draws attention to the recent research and findings in this field and is expected to guide engineers/researchers in future theoretical, numerical, and experimental studies.     

Numerical study on the case effect of a bomb air explosion

When considering the bomb explosion damage effect, the air shock wave and high-speed fragments of the bomb case are two major threats. In experiments, the air shock wave was studied by the bare ex-plosives superseding the real cased bomb; in contrast, the bomb case influence was ignored to reduce risk. The air explosion simulations of the MK84 warhead with and without the case were conducted. The numerical simulation results showed that the bomb case significantly influenced the shock wave generated by the bomb: the spatial distribution of shock wave in the near field changed, and the peak value of shock wave was reduced. Breakage of the case and kinetic energy of the fragmentation consumed 3 and 38% of the explosion energy, respectively. The increasing factors of the peak over-pressure induced by the bare explosive on the ground and in the air were 1.43-3.04 and 1.37-1.57, respectively. Four typical stages of case breakage were defined. The mass distribution of the fragments follows the Mott distribution. The initial velocity distribution of the fragments agreed well with the Gurney equation.     

高超音速导弹气动光学效应研究方法综述

气动光学效应是高超音速导弹设计需要解决的关键技术。全面论述了气动光学效应的定量研究方法,包括:小孔径技术、统计方法、随机相位屏方法和涡动力学研究方法,指出了工程上广泛使用的统计方法的适用范围,建议使用大涡模拟方法进行气动光学效应的数值仿真。     

制导航空子母炸弹高速抛撒分离数值仿真

制导航空子母炸弹在跨音速抛撒子弹药过程中，子弹药与母弹的分离伴随着复杂的流场和激波干扰，该过程中不仅存在着激波与激波的相互碰撞、部分激波的多次反射，而且由于受到多体运动的相互作用，其气流方向也发生变化，形成了变化复杂的压力、速度分布区域。采用数值模拟的方法对制导航空子母炸弹子弹药高速抛撒分离过程进行了数值仿真分析，应用嵌套网格技术，耦合多体动力学方程以及 N－S 方程求解子母炸弹高速分离过程，为工程设计、研究提供理论指导与计算依据。     

Interface defeat studies of long-rod projectile impacting on ceramic targets

The interface defeat phenomenon always occurs when a long-rod projectile impacting on the ceramic target with certain velocity, i.e., the projectile is forced to flow radially on the surface of ceramic plates for a period of time without significant penetration. Interface defeat has a direct effect upon the ballistic performance of the armor piercing projectile, which is studied numerically and theoretically at present. Firstly, by modeling the projectiles and ceramic targets with the SPH (Smoothed Particle Hydrodynamics) particles and Lagrange finite elements, the systematic numerical simulations on interface defeat are performed with the commercial finite element program AUTODYN. Three different responses, i.e., complete interface defeat, dwell and direct penetration, are reproduced in different types of ceramic targets (bare, buffered, radially confined and oblique). Furthermore, by adopting the validated numerical algorithms, constitutive models and the corresponding material parameters, the influences of projectile (material, diameter, nose shape), constitutive models of ceramic (JH-1 and JH-2 models), buffer and cover plate (thickness, constraints, material), as well as the prestress acted on the target (radial and hydrostatic) on the interface defeat (transition velocity and dwell time) are systematically investigated. Finally, based on the energy conservation approach and taking the strain rate effect of ceramic material into account, a modified model for predicting the upper limit of transition velocity is proposed and validated. The present work and derived conclusions can provide helpful reference for the design and optimization of both the long-rod projectile and ceramic armor.     

Study on performance degradation and failure analysis of machine gun barrel

An increase in the use of the gun barrel will cause wear of the inner wall, which reduces the muzzle velocity and the spin rate of the projectile. The off-bore flight attitude and trajectory of the projectile also change, affecting the shooting power and the accuracy. Exterior ballistic data of a high-speed spinning projectile are required to study the performance change. Therefore, based on the barrel's accelerated life test, the whole process of projectile shooting is reproduced using numerical simulation technology, and key information on the ballistic performance change at each shooting stage are acquired. Studies have shown that in the later stages of barrel shooting, the accuracy of shooting has not decreased significantly. However, it is found that the angle of attack of the projectile increases as the wear of the barrel increases. The maximum angle of attack reaches 0.106 rad when the number of shots reaches 4300. Meanwhile, elliptical bullet hole has appeared on the target at this shooting stage. Through combining external ballistic theory with simulation results, the primary reason of this phenomenon is found to be a significant decrease in the muzzle spin rate of the projectile. At the end of the barrel life, the projectile muzzle spin rate is 57.5% lower than that of a barrel without wear.