粘弹性介质中球形空腔嵌入层的共振特性研究

潜艇吸声覆盖层在低频对抗主动声纳的探测是目前面临的一个重要技术难题.利用空腔共振时的吸收是解决低频吸声问题的一种有效途径.文中在假设入射球形纵波完全被腔壁反射的情形下,对球形空腔嵌入层的共振特性进行了理论分析.结果表明,在粘弹性介质中嵌入适当厚度的低剪切波速包覆层能有效地降低空腔共振的频率.     

目次

为改善等离子体合成射流激励器在稀薄空气环境中的控制效果,增强其临近空间环境适应性,开展了腔体增压条件下激励器工作特性的研究。建立了腔体增压效果理论分析模型,计算结果表明:采用高压气源供气可以较好地提升激励器腔体气压,并且腔体气压对高压气源气压具有较好的跟随性,从而为射流强度调节提供了一种新的方式。搭建了腔体增压等离子体合成射流激励器实验系统,开展了腔体增压压力和射流流场特性测量,实验测量结果与计算结果吻合良好,误差小于2.6%。高速纹影观测显示:在腔体增压作用下,激励器控制力得到显著改善,射流锋面峰值速度由256 m/s提升至507 m/s。     

弯曲载荷作用下复合材料T型接头的失效分析

运用蔡-吴逐步失效判据和黏聚接触模型建立弯曲加载下的T型接头的有限元模型。对复合材料T型接头在弯曲加载下的损伤机理和承载能力进行数值模拟。结合静态弯曲加载实验,揭示T型接头在弯曲破坏过程中的四种失效模式。T型接头的弯曲失效载荷的有限元模型计算结果与实测值吻合较好。     

空腔噪声非线性数值模拟

将雷诺平均N-S方程与非线性噪声求解方法相结合,对M219空腔在Ma=0.6,Ma=0.85,Ma=1.35条件下进行了气动噪声分析。通过雷诺平均N-S方程求解空腔流场,得到包含空腔平均流场基本特征以及强制设定的湍流脉动统计描述的初始湍流统计平均解,采用非线性噪声求解方法重构噪声源并高精度模拟压力脉动的传播。通过与试验结果对比表明非线性噪声求解方法能够较好地捕捉空腔流动中的压强脉动及噪声水平。与分离涡模拟方法相比,非线性噪声求解方法在保持计算精度的同时大大减少计算网格,对内埋弹舱快速设计具有一定的参考意义。     

Resistance of grid steel-tube-confined concrete targets against projectile impact: Experimental investigation and analytical engineering model

Steel-tube-confined concrete (STCC) targets are provided with excellent anti-penetration performance over semi-infinite concrete (SIC) targets since the steel tube imposes passive restraint on the in-filled concrete during the penetration process. Grid STCC system with square steel tubes is a potential solution to protective structures. In this paper, experiments of 9-cell grid STCC targets penetrated by 12.7 mm Armor Piercing Projectile (APP) were performed. The influence of side length and thickness of steel tube, steel ratio and impact velocity on anti-penetration performance were taken into account. Additionally, single-cell square STCC targets were also designed and tested for comparison with the 9-cell grid STCC targets. Damage modes and parameters of the tested targets were measured and discussed. Moreover, the stiffness of radial confinement of grid STCC targets is achieved according to the elastic solution of infinite cylindrical shell in Winkler medium. Furthermore, the penetration resistance and depth of penetration (DOP) for grid STCC targets are obtained on the basis of the dynamic finite spherical cavity-expansion (FSCE) models including radial confinement effect. It is shown that the 9-cell grid STCC targets with optimal dimension match of thickness and side length of steel tube can reduce the DOP by about 17 % and 23 % in comparison with the SIC targets and single-cell square STCC targets, respectively, due to both the confinement of square steel tube to concrete in the impacted cell and the additional confinement of the surrounding cells to the impacted cell; the penetration resistance and DOP of the grid and cellular STCC targets with similar steel ratio is close, and thus the grid STCC targets with simpler manufacturing process and excellent in-plane expandability are preferred in engineering practice; moreover, the predicted results of DOP model based on the FSCE models agree well with the tested results with the maximum disparity less than 12 % and the proposed model is more applicable to the grid and cellular STCC targets with high radial confinement.     

预处理方法在低速粘性流动中的应用

用时间相关法、LU SGS隐式求解经过预处理后的二维可压Navier Stokes方程 ,数值模拟了低速情况下不同马赫数、不同雷诺数的驱动空腔流动。为了使时间相关法能应用于计算低速流动及加快收敛 ,在控制方程的时间导数项前乘了一个预处理矩阵 ,实现了对方程的预处理。数值模拟结果表明 ,预处理确实加快了计算的收敛性 ,而定常解却没有改变。所得结果与可能的计算结果进行了比较     

机载激光器聚光腔的设计及试验

分析了影响固体激光器聚光腔效率的各种因素,对激光器的泵浦效率相对于聚光腔的几何形状、反射面镀层及冷却方式的关系进行了试验研究,提出了机载激光器聚光腔的设计原则。     

An air cavity method for increasing the underwater acoustic targets strength of corner reflector

In order to improve the underwater acoustic target strength of corner reflectors, according to the principle of acoustic impedance mismatch of the boundary layer, the method of using air cavity to increase the underwater acoustic target strength of corner reflectors is proposed. The acoustic reflection coefficients of underwater air layer and single layer metal sheet are calculated and compared. The results show that the reflection coefficient of single layer metal sheet is greatly affected by frequency and incidence angle, and the reflection coefficient of air layer in water is large and little affected by frequency and incidence angle. On this basis, a new kind of airfilled cavity corner reflector is designed. The acoustic scattering characteristics of underwater airfilled cavity corner reflector are calculated cumulatively, and the results are compared with the monolayer metal sheet corner reflector. The simulation results show that the acoustic reflection effect of the airfilled cavity corner reflector is better. In order to verify the correctness of the method, the test was carried out in the silencing tank. The experimental results show that the simulation results are in good agreement with the experimental results, and the airfilled cavity can improve on acoustic reflection performance of the underwater corner reflector.     

高速破片撞击充液容器形成液压水锤的试验研究

为研究高速破片撞击充液容器形成的液压水锤效应,设计一套试验装置和测试方法,试验破片撞击充液容器产生空腔的变化过程、液体中不同位置处的压力变化以及前后面板的变形情况。试验发现：破片撞击容器后面板时会出现一圈空化气泡,气泡在后面板内表面从撞击点位置迅速沿径向扩展;液压水锤初始冲击阶段,距离撞击点较近区域在初始冲击波压力脉冲过后会出现一个较大负压,而距离撞击点较远区域不受负压影响;破片撞击速度对容器前面板最大变形影响较小,变形范围随着撞击速度的增大沿撞击点向四周扩展。后面板的最大变形及变形范围都随着破片撞击速度的增大而变大。     

钢球侵彻不同靶标的相似性分析

为研究相同弹丸侵彻不同靶标所造成损伤之间的相似性,以钢球侵彻明胶造成的瞬时空腔的最大直径为研究对象,基于相似理论推导出瞬时空腔最大直径的相似准则方程,利用钢球侵彻明胶的实验数据求解出准则方程的系数和指数,最后通过钢球侵彻猪后腿实验验证了所得到的准则方程可用于不同靶标之间的相似性分析,并具有准确性和合理性。