新型钢-混凝土组合板的力学性能研究

以加劲肋形式、组合板厚度和栓钉布置为参数,进行了9块新型组合板的力学性能试验.试验结果表明,组合板的正截面承载力可按基于修正平截面假定的极限状态计算;组合板的跨中挠度,可在按现行规范计算的基础上,加上考虑界面滑移影响的附加变形值予以修正.     

Effect of projectile parameters on opening behavior of PELE penetrating RC target

When a penetrator with enhanced lateral effect (PELE) impacts on a reinforced concrete (RC) target, the target is damaged with a large opening. An understanding of how PELE projectile parameters affect the opening dimension, is essential for effective design of the PELE projectile. In this study, under the condition that the impact velocity and target parameters (strength and thickness) were fixed values, the important influence factors of the PELE (jacket wall thickness B, jacket material strength Y1, filling material strength Y2 and angle of monolithic jacketθ) were determined by a dimensional analysis. Tests and simulations of the PELE penetrating the RC target were conducted to analyze the influence of these factors on opening diameter ((D), an equivalent diameter under relative kinetic energy). Based on the test and simulation results, it is found that the influence of these factors B, Y1 andθon the deformation mode of the jacket shows a similar trend:as values of the three factors decrease, the jacket deforms from small bending deformation to large one, and then to curling deformation. This causes the opening diameter to first increase with the decrease of these three factors, and then decreases. It is well known that the bending resistance of the jacket is related to these factors B, Y1 andθ. Therefore, a plastic limit bending moment (M0) of the jacket was quoted to characterize the influence of these factors on the bending deformation of the jacket and the opening diameter of the target. The influence factor Y2 causes (D) to first increase with the increase of Y2, and then decreases. A formula was developed to predict the opening diameter, whose influence parameters were considered in a dimensionless way. It has been shown that the dimensionless opening diameter (D)/d1 is dependent on two dimensionless parameters Q = (d31fc/M0) and G = (fc/Y2), where d1 and fc are the outer diameter of the projectile and the compressive strength of the target, respectively.     

钢筋钢纤维混凝土既有裂缝梁中钢纤维阻裂作用有限元分析

通过建立钢筋钢纤维混凝土既有裂缝梁和钢筋混凝土既有裂缝梁的有限元分析模型,借助ANSYS分析了两种梁在荷载作用下的裂缝尖端处应力、裂缝宽度增幅和挠度并作出对比。分析结果表明钢纤维对裂缝开展有很好的阻止作用,而且能明显缓和裂缝尖端处应力,减小梁的挠度。     

磺化酚醛树脂的研究:高效减水剂的制备及其对混凝土工作度和力学性能的影响

制备了以磺化酚醛树脂为基础的3种高效减水剂,该高效减水剂能显著地减少用水量和改善混凝土工作度以及力学强度.测试结果显示:随掺量的增加,混凝土抗压强度在一定范围内有明显的提高,然后增加较慢或有所下降;混凝土的抗折、抗拉、抗剪强度以及与钢筋的粘接强度均高于对照空白样.同硅灰、磨砂矿渣相结合还获得了抗压强度大于100MPa、流动性好的超高强混凝土.     

新型BFRP筋增强混凝土受弯构件挠度控制

玄武岩纤维塑料增强筋（BFRP筋）的特性导致以其为增强筋的受弯构件出现裂缝后刚度降低非常明显,变形发展过快。因此,对BFRP筋混凝土梁的设计主要应根据其变形性能标准的要求来进行。为方便设计人员进行BFRP筋受弯构件设计,结合试验研究,通过对比国内外有关FRP筋混凝土梁开裂截面有限惯性矩计算模型的研究,探索出适合BFRP筋混凝土梁开裂截面有效惯性矩计算模型;通过建模分析,表明有限元计算模型和其他几种计算模型一起可以应用于BFRP筋混凝土梁直接挠度控制。推导出FRP筋受弯构件配筋率计算公式,结合直接挠度控制研究,提出通过控制跨高比限值来进行梁尺寸初选的间接挠度控制计算公式。     

型钢混凝土桁架节点有限元分析

由于普通结构设计软件无法实现型钢混凝土空间桁架节点内部细化计算分析,为解决这一问题,通过采用ANSYS软件对整体结构进行静力分析,并提取桁架节点处各构件的内力,将其施加于桁架节点的实体模型,进行精细的有限元计算分析;检验桁架节点实体模型内部应力是否满足强度要求,验证结构设计时节点区域的型钢选取和配筋的合理性;同时将分析结果与在该结构施工现场实际检测结果进行对比。结果表明,AN—SYS软件能够准确地完成普通结构设计软件无法完成的复杂结构模型的细化有限元分析。     

高掺量碳纤维增强活性粉末混凝土力学性能实验

采用一种新的碳纤维自分散工艺和专用分散设备制备出了掺量达胶结材质量8％的碳纤维增强活性粉末混凝土;研究了碳纤维掺量对活性粉末混凝土的力学性能影响规律。实验结果表明,在碳纤维掺量高时,活性粉末混凝土的力学性能受碳纤维掺量和水胶比两个因素共同作用。     

Polyurea coating for foamed concrete panel: An efficient way to resist explosion

Autoclaved aerated concrete (AAC) panels have ultra-light weight, excellent thermal insulation and energy absorption, so it is an ideal building material for protective structures. To improve the blast resistance of the AAC panels, three schemes are applied to strengthen the AAC panels through spraying 4 mm thick polyurea coating from top, bottom and double-sides. In three-point bending tests, the polyurea-coated AAC panels have much higher ultimate loads than the un-coated panels, but slightly lower than those strengthened by the carbon fiber reinforced plastics (CFRPs). Close-in explosion experiments reveal the dynamic strengthening effect of the polyurea coating. Critical scaled distances of the strengthened AAC panels are acquired, which are valuable for the engineering application of the AAC panels in the extreme loading conditions. Polyurea coatings efficiently enhance the blast resistance of the bottom and double-sided polyurea-coated AAC panels. It is interesting that the polyurea-coated AAC panels have much more excellent blast resistance than the CFRP reinforced AAC panels, although the latter have better static mechanical properties.     

混凝土板模爆方法数值模拟研究

分析混凝土结构在1/4模型中应变率对于爆炸相似律的影响,并用数值模拟的方法进行混凝土板的模爆方法研究,得出混凝土板在爆炸作用下复印比例定律近似成立的结论。考察数值模拟中产生计算误差的原因,发现混凝土板模型在采用4cm网格时会出现较大的计算偏差,其原因部分是由于网格尺寸引起的,部分是由于计算采用的混凝土局部损伤失效模型引起的。     

火灾场钢筋混凝土简支梁抗弯性能分析

通过对火灾中钢筋混凝土简支梁截面温度场和材料热力学性能分析,将混凝土分为弹性区和塑性区来分别计算其强度,建立了火灾场简支梁截面内混凝土应力和梁极限抗弯承载力的计算公式,通过具体算例分析了钢筋混凝土简支梁截面温度场和极限承载力的变化规律和原因。