脉冲防暴水炮非淹没气体射流的RANS和LES模拟

为提高脉冲防暴水炮刺激剂的雾化水平,必须提高射流的出口速度和改善雾化带形状,而这些因素与管内非淹没气体射流的湍流流场息息相关。为准确描述湍流分布和水柱加速过程,对脉冲防暴水炮的非淹没气体射流进行了RANS和LES模拟。结果表示LES模型较RANS的标准k-ε模型能更为精确地描述湍流分布和管内非淹没气体射流速度的各向异性。但两者对于水柱加速过程的描述基本一致,只是由于LES模型的气液参混较为充分,气液速度相差较小,而可能导致两模型气体在喷口膨胀规律的异同。LES模型气液界面复杂,是用于研究管内气液流型的理想方法。该方法为三维模拟打下了较好的基础,所得结果可以作为管外射流研究的初始条件。     

高温燃气与不同构型的再生冷却面板对流传热的数值模拟

对高温燃气与带有平行冷却通道的再生冷却面板之间的三维耦合传热开展了数值研究,其中冷却通道内冷却剂为超临界压力煤油,并结合理论分析探讨了冷却面板构型对耦合传热的影响。结果表明:随燃气侧壁厚以及冷却通道宽度和高度的增大,燃气侧壁面温度升高,热流密度降低。研究还发现:冷却通道不同壁面传递给煤油的热量占比几乎不随燃气侧壁厚变化,但随冷却通道宽度和高度的改变而变化。     

Investigation on the process parameters of TIG-welded aluminum alloy through mechanical and microstructural characterization

Multi-pass TIG welding was conducted on plates (15×300×180 mm3) of aluminum alloy Al-5083 that usually serves as the component material in structural applications such as cryogenics and chemical processing industries. Porosity formation and solidification cracking are the most common defects when TIG welding Al-5083 alloy, which is sensitive to the welding heat input. In the experiment, the heat input was varied from 0.89 kJ/mm to 5 kJ/mm designed by the combination of welding torch travel speed and welding current. Tensile, micro-Vicker hardness and Charpy impact tests were executed to witness the impetus response of heat input on the mechanical properties of the joints. Radiographic inspection was performed to assess the joint's quality and welding defects. The results show that all the specimens displayed inferior mechanical properties as compared to the base alloy. It was established that porosity was progressively abridged by the increase of heat input. The results also clinched that the use of me-dium heat input (1-2 kJ/mm) offered the best mechanical properties by eradicating welding defects, in which only about 18.26% of strength was lost. The yield strength of all the welded specimens remained unaffected indicated no influence of heat input. Partially melted zone (PMZ) width also affected by heat input, which became widened with the increase of heat input. The grain size of PMZ was found to be coarser than the respective grain size in the fusion zone. Charpy impact testing revealed that the absorbed energy by low heat input specimen (welded at high speed) was greater than that of high heat input (welded at low speed) because of low porosity and the formation of equiaxed grains which induce better impact toughness. Cryogenic (-196 C) impact testing was also performed and the results corroborate that impact properties under the cryogenic environment revealed no appreciable change after welding at designated heat input. Finally, Macro and micro fractured surfaces of tensile and impact specimens were analyzed using Stereo and Scanning Electron Microscopy (SEM), which have supported the experimental findings.     

Numerical investigation on cooling performance of filter in a pyrotechnic gas generator

As a key part of the pyrotechnic gas generator,the filter not only removes the particulate matter but also cools the hot gas to a safe level.This paper aims to improve the understanding of the basic heat and flow phenomenon in the gas generator.The pyrotechnic gas generator is modelling by a simplified filter structure with fiber arrays.A finite-volume model of the heat and fluid flow is proposed to simulate the detailed multi-dimensional flow and energy conversion behaviors.Several verification results are in good agreement with data in different references.Simulation results demonstrate that the filter can not only absorb heat from the gas but also cause the high intensity enhancement of the heat transfer.The per-formance difference between inline and staggered arrays is also discussed.The findings of the study put a further prediction tool for the understanding and design of the filter system with fibers.     

有限时间热力学研究的一些进展

介绍近年来在不可逆热机理论、回热式燃气轮机循环分析、类热机装置分析和广义热力学优化理论研究中的一些进展 ,并简要阐述其发展方向 .     

无铅汽油中烯烃、芳烃含量的分析

随着环境保护意识的加强,车用无铅汽油国家标准GB 17930-1999中对烯烃、芳烃含量提出了明确限值要求。相应分析方法是GB／T 11132-2002液体石油产品烃类测定法(荧光指示剂吸附法,FIA),该方法操作过程复杂,试验时间长,试验结果偏差大。为改进对汽油中烯烃、芳烃含量的测试方法,人们在这方面做了大量研究工作。对目前采用的快速、简便分析汽油中烯烃、芳烃含量的气相色谱和近红外光谱分析方法进行了评述。     

大功率气体开关重复频率的理论分析

分析了影响气体开关重复频率的各因素,从理论上推导了开关耗能的恢复时间以及气体的冷却时间对重复频率的影响。提出了提高重复频率的方法。     

航天器推进系统气液路故障仿真

为了研究和分析航天器推进系统气液路故障的发展变化规律及对整个推进系统性能的影响,在某挤压式航天器推进系统仿真模型的基础上,分别采用Realizable k-ε湍流模型和一维可压缩流模型对气路泄漏和堵塞故障进行动态仿真,采用一维不可压瞬变管流模型与变流量系数模型对液路泄漏和堵塞故障进行仿真分析。仿真结果表明:推进系统增压气路堵塞和泄漏故障,会导致增压不足,使推进剂供应管路压强下降;推进剂供应管路堵塞故障和泄漏故障会导致混合比偏离设计值,使推进系统性能降低。两类故障都会引起推力不足,致使系统性能降低。两者的不同之处在于:堵塞故障下,故障组件上游压强高于额定工况,推进剂消耗低于额定工况;泄漏故障下,故障组件上游压强低于额定工况,推进剂消耗高于额定工况。     

气液比对液体中心式气液同轴离心喷嘴燃烧过程的影响

为了分析气液比对液体中心式气液同轴离心喷嘴燃烧过程的影响,针对一台采用液体中心式气液同轴离心喷嘴的燃气发生器在不同气液比下进行热试,并对试验结果进行深入分析。结果表明:随着气液比的增加,燃烧过程存在三种状态——稳定燃烧、稳定燃烧过渡到低频不稳定燃烧、低频不稳定燃烧。这种低频不稳定燃烧与供应系统的振荡无关,是由气液比增加造成三岔火焰远离喷注面板,当三岔火焰到达喷雾撞击点后火焰稳定性降低,使得火焰在回流区内前后振荡引起的。     

醋酸纤维素膜除湿技术研究

制备了一系列醋酸纤维素膜,采用静态法评价了水及DMMP通过膜的渗透量,并用自行设计的除湿膜装置评价了膜的除湿效果．结果表明,当在膜外侧采取用干燥空气吹扫时,进气流速越低除湿效果越好．