Investigation on the process parameters of TIG-welded aluminum alloy through mechanical and microstructural characterization

Multi-pass TIG welding was conducted on plates (15×300×180 mm3) of aluminum alloy Al-5083 that usually serves as the component material in structural applications such as cryogenics and chemical processing industries. Porosity formation and solidification cracking are the most common defects when TIG welding Al-5083 alloy, which is sensitive to the welding heat input. In the experiment, the heat input was varied from 0.89 kJ/mm to 5 kJ/mm designed by the combination of welding torch travel speed and welding current. Tensile, micro-Vicker hardness and Charpy impact tests were executed to witness the impetus response of heat input on the mechanical properties of the joints. Radiographic inspection was performed to assess the joint's quality and welding defects. The results show that all the specimens displayed inferior mechanical properties as compared to the base alloy. It was established that porosity was progressively abridged by the increase of heat input. The results also clinched that the use of me-dium heat input (1-2 kJ/mm) offered the best mechanical properties by eradicating welding defects, in which only about 18.26% of strength was lost. The yield strength of all the welded specimens remained unaffected indicated no influence of heat input. Partially melted zone (PMZ) width also affected by heat input, which became widened with the increase of heat input. The grain size of PMZ was found to be coarser than the respective grain size in the fusion zone. Charpy impact testing revealed that the absorbed energy by low heat input specimen (welded at high speed) was greater than that of high heat input (welded at low speed) because of low porosity and the formation of equiaxed grains which induce better impact toughness. Cryogenic (-196 C) impact testing was also performed and the results corroborate that impact properties under the cryogenic environment revealed no appreciable change after welding at designated heat input. Finally, Macro and micro fractured surfaces of tensile and impact specimens were analyzed using Stereo and Scanning Electron Microscopy (SEM), which have supported the experimental findings.     

深水环境下潜艇舯部结构撞击强度数值分析

潜艇结构水下碰撞是潜艇的主要事故形式,也是船舶碰撞最为危险的状态之一。文中首先提出潜艇碰撞问题,对碰撞特征进行分析,然后针对某型潜艇舯部典型结构的撞击极限强度特性进行数值计算,结果显示,由于准静压载荷的附连耦合作用,随着静水压力的增加,潜艇舯部耐压壳体结构的防撞能力将大幅下降,而耐压壳体内部平台和舱壁结构将有效提高壳体结构的横向失稳临界应力,改善潜艇结构的径向耐撞能力。     

舰船静置爆炸气泡时总纵强度计算方法研究

新型"大气泡能"概念武器在水下爆炸能产生大气泡,对船体总纵强度造成很大影响,有可能使舰体发生纵向折断或倾覆。为研究这种作用,建立了舰船静置爆炸气泡时总纵弯曲强度的理论计算方法。采用静置爆炸气泡的假设,将气泡产生的浮力损失和压力差转化为等效载荷,计算气泡作用后船体的总纵弯矩和剪力并进行强度校核。以某舰艇为例进行计算,结果表明,爆炸气泡作用下船体的剪力和弯矩比静浮状态增大很多,船体发生纵向折断破坏的危险性也随之增大。     

基于多元高斯概率分布的无线局域网定位方法研究

针对无线局域网环境及室内目标定位需求,研究了基于接收信号强度指示的定位技术,提出了一种基于多元高斯概率分布的信号强度模式匹配方法,讨论了定位系统框架。试验结果表明,该方法具有较好的室内定位效果。     

基于贝叶斯网络的态势估计时间推理方法

基于贝叶斯网络的态势估计方法是目前态势估计领域中的主要方法之一,然而,传统的贝叶斯网络不具备时间语义,因此无法解决态势估计中的时间推理问题.基于此,对贝叶斯网络进行改造,研究了时间贝叶斯网络的构建方法.通过一个战场想定,说明了时间贝叶斯网络构建、推理的过程与方法,证明了提出方法的有效性.     

区域防空兵力需求优化模型研究

区域防空兵力需求是防空作战保障部门实施高效保障的基本依据,也是进行区域防空作战布势的前提和基础。讨论了地面防空兵器和空袭兵器作战效能指数的计算方法,建立了地空对抗条件下的兰切斯特动态方程,得出了满足一定作战效能指标的区域防空各型防空火力单元的数量与规模。     

鱼雷命中后舰船的载荷计算和剩余强度评估

以某舰船为例,计算了鱼雷在舰船底部非接触爆炸使舰体结构产生破损后由于进水引起的浮态和载荷变化,给出了鱼雷命中破损后波浪弯矩随不同破损部位、不同进水体积的变化规律.计算了破损舰船的弹塑性极限弯矩,并对舰船的剩余强度进行了评估.计算结果表明,鱼雷命中的最危险位置是船中,外载荷的增大和结构承载能力的减小使舰体结构在单发命中时也可能失效.     

基于两级供应关系的军械战备器材存储模型研究

提出了在一定经费的约束条件下,使所有二级存储场站的所有战备器材期望缺货数最小的模型,通过对后方仓库存量初值和场站库存量的确定,求解出后方仓库和场站之间库存量的优化分配调整方案。最后通过实例得出发散型布局形态模型。     

在现代化背景下重解“传统”

对人们思想观念中关于"传统"和"现代"的种种误区进行了分析和批评,对"传统"与"现代"的关系、传统文化的真正含义以及现代化的本质等问题予以深入的讨论,进而针对在当代中国城市和建筑发展中如何正确理解"传统"和"现代",如何正确思考和处理二者之间的关系等问题提出了见解.     

磁悬挂天平校准关系的非线性拟合

以磁悬挂天平系统的校准为研究背景 ,介绍了传统的校准关系的线性建模方案 ,针对其存在的缺陷 ,并结合校准实验数据的特点 ,提出了非线性拟合的改进方案 ,该方案借鉴了主成份分析法的合理成分 ,采用三次样条拟合方法建立校准关系 ,获得了令人满意的实际效果 ,最后 ,还定量比较了校准拟合的改进方案和传统的线性建模方案。