协同空战的最小共享信息集

首先提出了最小共享信息集的概念。然后 ,提出了作战飞机的智能系统模型。从它入手 ,分析了协同空战的信息 ,提出了确定协同空战的最小共享信息集的事件法 ,并应用信息论证明了事件法的确能够减少通信的信息量。在上述基础上 ,确定了超视距空对空协同作战的最小共享信息集 ;仿真结果验证了它的合理性     

单片机系统常用软硬件抗干扰措施

抗干扰性能是微机系统可靠性的重要指标,抗干扰设计是单片机系统研制中不容忽视的重要内容。单片机系统的可靠性由多种因素决定,从干扰的来源和途径,分析干扰对单片机主要硬件CPU、SFR、RAM、ROM及软件的影响,探索抗干扰的原理和设计方法。提出从电源、输入通道、印制板电路加强硬件抗干扰;通过开机自检、掉电保护、睡眠抗干扰及"看门狗"等技术,采用指令冗余和软件陷阱等软件措施,及时发现干扰导致的错误,使系统尽快恢复正常或及时报警,最大限度降低干扰对系统的影响,有效提高单片机系统在恶劣工况下运行的可靠性。     

基于测试码并行的同步时序电路故障模拟方法

将组合电路故障模拟的一些加速技术推广到时序电路故障模拟中,提出并实现了一个功能块级的基于测试码并行的同步时序电路故障模拟方法,对部分ISCAS89 Benchmark电路的模拟结果表明,该故障模拟方法有较好的性能.     

Single machine sequencing with linear models of release dates

The paper deals with a problem of scheduling a set of jobs on a single machine. Before a job is released for processing, it must undergo some preprocessing treatment that consumes resources. It is assumed that the release date of a job is a linear decreasing continuous function of the amount of a locally and globally constrained, continuously divisible resource (e.g., energy, catalyzer, financial outlay, gas). The problem is to find a sequence of jobs and a resource allocation that will minimize the maximum job completion time. Such a problem appears, for example, in the ingot preheating and hot-rolling process in steel mills. It is shown that the problem is strongly NP-hard. Some polynomially solvable cases of the problem and approximate algorithms with both experimental and worst-case analysis are presented. © 1998 John Wiley & Sons, Inc. Naval Research Logistics 45: 99–113, 1998     

单级入轨运载器干质量影响因素分析

提出了单级入轨运载器干质量计算方法。对给定的飞行任务,提出了基准运载器,并计算了贮箱材料、热防护系统及设计余量对运载器干质量的影响。计算结果表明,先进的材料和设计能降低运载器的干质量,并使运载器干质量对设计余量的敏感性降低     

炮兵对有生力量压制比的仿真计算方法

为了评估炮兵对有生力量压制效果,应用离散事件仿真方法建立了炮兵射击有生力量仿真模型,提出一种炮兵对有生力量压制比的仿真计算方法。首先,给出了压制比的概念与模型。然后,建立了基于离散事件仿真的炮兵射击有生力量模型。最后,结合实例验证了仿真计算方法的正确性。     

A hybrid method for simulation factor screening

Factor screening is performed to eliminate unimportant factors so that the remaining important factors can be more thoroughly studied in later experiments. Controlled sequential bifurcation (CSB) and controlled sequential factorial design (CSFD) are two new screening methods for discrete‐event simulations. Both methods use hypothesis testing procedures to control the Type I Error and power of the screening results. The scenarios for which each method is most efficient are complementary. This study proposes a two‐stage hybrid approach that combines CSFD and an improved CSB called CSB‐X. In Phase 1, a prescreening procedure will estimate each effect and determine whether CSB‐X or CSFD will be used for further screening. In Phase 2, CSB‐X and CSFD are performed separately based on the assignment of Phase 1. The new method usually has the same error control as CSB‐X and CSFD. The efficiency, on the other hand, is usually much better than either component method. © 2009 Wiley Periodicals, Inc. Naval Research Logistics, 2010     

一种消除直线永磁无刷直流电机边端效应对换相时机影响的方法

电磁弹射用直线永磁无刷直流电机的永磁体动子具有开断结构,使动子边端的磁场分布发生变形。当采用霍尔元件检测磁场实现换相时,这种边端效应就会影响换相时机。分析了这类电机的换相机理和动子开断结构对换相时机的影响,指出这类边端效应受极弧系数影响显著,并提出了利用不对称滞环比较器或简易单限比较器对霍尔输出信号进行处理从而消除这类边端效应影响的方法,实验验证了简易单限比较器方案的可行性。     

A note on combined job selection and sequencing problems

We investigate the solvability of two single‐machine scheduling problems when the objective is to identify among all job subsets with cardinality k,1≤k≤n, the one that has the minimum objective function value. For the single‐machine minimum maximum lateness problem, we conclude that the problem is solvable in O(n²) time using the proposed REMOVE algorithm. This algorithm can also be used as an alternative to Moore's algorithm to solve the minimum number of tardy jobs problem by actually solving the hierarchical problem in which the objective is to minimize the maximum lateness subject to the minimum number of tardy jobs. We then show that the REMOVE algorithm cannot be used to solve the general case of the single‐machine total‐weighted completion time problem; we derive sufficient conditions among the job parameters so that the total weighted completion time problem becomes solvable in O(n²) time. © 2013 Wiley Periodicals, Inc. Naval Research Logistics 60: 449–453, 2013     

A PANEL DATA ANALYSIS OF THE NEXUS BETWEEN DEFENCE SPENDING AND GROWTH IN THE EUROPEAN UNION: A COMMENT

Abstract

This paper explains and assesses the UK experience with determining prices and profitability for non-competitive defence contracts. Three periods are considered, namely pre-1968, the 1968 Profit Formula Agreement and the changes introduced in 2014. Two cases of ‘excessive’ profits were major determinants of the 1968 Profit Formula Agreement; but continued dissatisfaction with the 1968 Agreement led to changes in 2014. The historical overview of UK experience provides a basis for understanding current UK policy and offers insights for other countries facing similar policy challenges. A critique is presented of UK policy on single source pricing and profitability.