Experiment and simulation of launching process of a small-diameter steel cartridge case

In order to explore the rules of the deformation force during the launching of a small-diameter steel cartridge, the semi-closed bomb test method is used to test the greatest strains on chamber outer wall under the different chamber pressures. The pressure curves of cartridge chamber are measured in experiment, and the tensile test data of cartridge are loaded into the numerical calculation to compare with the experimental data. The conclusion was obtained that the calculated results match better with the experimental results by considering strain rate bilinear kinematic hardening material constitutive model. The forces on the various parts of the cartridge during launching and their deformation rules are achieved, in which the equivalent plastic strain decreases and the cylinder ring withstands the maximum equivalent stress when the cartridge case clings to the bore from the mouth to the bottom.     

Theoretical and numerical investigations on the headspace of cartridge cases considering axial deformation and movement

The cartridge case headspace is the axial clearance between the cartridge and bolt of an automatic weapon, and influences the reliability and security of the weapon. Accordingly, theoretical and numerical studies were conducted to analyze the dynamic response of cartridge cases during internal impact considering the initial radial clearances between the cartridge case and chamber. A theoretical model was proposed to predict the cartridge case headspace considering both the deformation and movement of the cartridge case and confirmed by the results of nonlinear finite element simulations. The differences between the results of the conventional static model and the dynamic model were then comprehensively evaluated. The effects of the angle between the cartridge and chamber, the cartridge case material, and the internal impact pressure on the predicted headspace value were also analyzed. The dynamic response of the cartridge case predicted by the dynamic model was more accurate than that predicted by the conventional static model. The internal impact pressure, pressure change rate, and cartridge material were all found to affect the predicted headspace.     

Influences of different crossing types on dynamic response of underground cavern subjected to ground shock

An intersecting cavern is a common structural form used in underground engineering, and its safety and stability performance directly control the service performance of the whole project. The dynamic re-sponses of the three kinds of crossing type (+-shaped, T-shaped, L-shaped) caverns subjected to ground shock were studied by numerical simulation. The velocity plus force mode boundary setting method was proposed in the coupled static and dynamic analysis of a deep underground cavern. The results show that, among the three types of crossing caverns, the+-shaped cavern is the most significantly affected by the dynamic action, followed by T-shaped, and then L-shaped caverns. The vault settlement, straight wall deformation, vault peak particle velocity, effective plastic strain of surrounding rock, and maximum principal stress and strain at the bottom of the lining of the straight wall increase with the increase of cavern span. The vault settlement, straight wall deformation, effective plastic strain of surrounding rock, and the maximum principal stress and strain at the bottom of lining to the straight wall decrease with the increase of lateral pressure coefficient, and the peak particle velocity at the vault increases. The variation is small compared with the change of cavern span. The influence range of the underground cavern intersection is two cavern diameters from the intersection centre. The bottom of the straight wall at the intersection is the weak part. It is suggested to thicken the support locally to improve the stability of the cavern.     

超空泡水下航行体振动特性分析

用有限元方法分析了超空泡水下航行体的固有特性,计算了自由边界条件下超空泡航行体的振动特性,求出了固有频率和模态,并选取对其结构性能有重要影响的四类模态,即梁弯曲模态、呼吸模态、径向模态和轴向弯曲模态绘制了三维模态图.研究表明,超空泡水下航行体无阻尼自由振动的首阶模态为梁弯曲模态;呼吸模态发生的初始频率较高;径向模态发生的初始频率较低;轴向弯曲模态发生的频率比较集中,变形较为复杂.所得结果为今后开展进一步的超空泡航行体结构动力学研究提供了模型基础.     

圆形减压环力学试验与壁厚对其耗能性能的影响

圆形减压环主要由钢管、铝管套筒和钢丝绳组成,由于其耗能特性强,因此在被动防护系统中得到了广泛应用。在边坡防护工程中,将钢丝绳一端固定,另一端连接在防护阻挡结构上,通过钢管与铝管套筒的摩擦和钢管的大变形来散耗冲击动能。首先分析了圆形减压环的工作原理,并对其力学性能进行了拟静力试验,再利用ANSYS/LS-DYNA软件,研究了圆形减压环在荷载作用下,不同钢管壁厚对其耗能性能的影响。结果表明：随着钢管壁厚的增加,圆形减压环的启动荷载也随之增大;在低速荷载作用下,钢管壁厚对圆形减压环的耗能性能影响较弱,但是随着加载速度的提高,钢管壁厚对其耗能性能的影响明显增加,耗能总量上升明显。     

装配式管线水力瞬变的非线性流固耦合模型

装配式管线是一种重要的油料保障装备,用于地面铺设,属于典型的薄壁弱约束管线系统。根据装配式管线的特点,应用管道弹性变形理论,推导了水力瞬变状态下装配式管线的非线性流固耦合5-方程模型。该模型充分考虑了管道与流体之间的耦合互动效应,耦合形式包含了泊松耦合、摩擦耦合、结合部耦合,以及管线系统的轴向、横向和径向振动耦合,并计及了管道结构阻尼的影响。针对装配式管线的特殊连接约束方式,提出了一种带有扭转弹簧的铰支型约束边界,可通过确定扭转弹簧的弹性系数来建立管线两端的约束边界方程。     

软硬交替多层膜法向压入过程的有限元分析

采用大变形弹塑性有限单元法,对高速钢基体上的软硬交替多层膜在法向压痕作用下的力学行为,进行了模拟和分析.为了研究膜层数和膜厚的影响,对从单层到16层的不同膜层体系进行了计算.通过对诸如膜层的变形、最大应力随膜层数的变化、界面剪应力分布、表面张应力分布等的分析,得出了这些参数的分布及其对膜层体系的摩擦学性能的影响.这些结果可为多层膜的结构优化设计提供定量的依据.     

土工格栅加筋土挡墙稳定性影响因素敏感性分析

以灰关联分析法为手段,通过有限元强度折减法计算加筋土挡墙的稳定安全系数。结合水富—麻柳湾高速公路的土工格栅加筋土挡墙实际工程,分析了各因素对土工格栅加筋土挡墙稳定影响的敏感性,按大小依次为：内摩擦角、筋土间摩擦系数、粘聚力、筋带长度、筋带轴向拉伸刚度、筋带间距和填土密度。建议设计中,如果条件许可应优先选择摩擦角和粘聚力较高的填料,当填料受限制时,要提高加筋土挡墙的稳定性可以优先考虑选择与填土有较高摩擦系数和轴向拉伸刚度较大的土工格栅进行设计。     

50000m~3油罐壁厚设计比较与分析

油罐的壁厚设计关系到油罐的经济性和可靠性,如何把握两者的辩证关系对油罐的设计与建设具有十分重要的意义。传统上大型油罐壁厚设计采用的是变点法;以可靠度理论为基础,以可靠性分析模型为核心,提出利用可靠度法求解大型油罐壁厚的新方法。以50 000 m3油罐为例,编程分析并计算以2种方法设计的壁厚。变点法设计的底圈罐壁厚度与圈数无关;以中心点可靠度法求解壁厚,可靠性指标一定时,底圈罐壁厚度同样与圈数无关。探讨可靠度法求解壁厚的可行性,验证变点法设计壁厚的可靠性。     

Effect of projectile parameters on opening behavior of PELE penetrating RC target

When a penetrator with enhanced lateral effect (PELE) impacts on a reinforced concrete (RC) target, the target is damaged with a large opening. An understanding of how PELE projectile parameters affect the opening dimension, is essential for effective design of the PELE projectile. In this study, under the condition that the impact velocity and target parameters (strength and thickness) were fixed values, the important influence factors of the PELE (jacket wall thickness B, jacket material strength Y1, filling material strength Y2 and angle of monolithic jacketθ) were determined by a dimensional analysis. Tests and simulations of the PELE penetrating the RC target were conducted to analyze the influence of these factors on opening diameter ((D), an equivalent diameter under relative kinetic energy). Based on the test and simulation results, it is found that the influence of these factors B, Y1 andθon the deformation mode of the jacket shows a similar trend:as values of the three factors decrease, the jacket deforms from small bending deformation to large one, and then to curling deformation. This causes the opening diameter to first increase with the decrease of these three factors, and then decreases. It is well known that the bending resistance of the jacket is related to these factors B, Y1 andθ. Therefore, a plastic limit bending moment (M0) of the jacket was quoted to characterize the influence of these factors on the bending deformation of the jacket and the opening diameter of the target. The influence factor Y2 causes (D) to first increase with the increase of Y2, and then decreases. A formula was developed to predict the opening diameter, whose influence parameters were considered in a dimensionless way. It has been shown that the dimensionless opening diameter (D)/d1 is dependent on two dimensionless parameters Q = (d31fc/M0) and G = (fc/Y2), where d1 and fc are the outer diameter of the projectile and the compressive strength of the target, respectively.     

多管火箭武器储运发射箱长期储存蠕变性能预测

为探究火箭武器储运发射箱长期储存的蠕变性能,制备复合材料层压板并开展单轴拉伸蠕变试验,获得了单向纤维复合材料主方向的蠕变本构模型参数。采用有限元方法并借助用户自定义材料子程序建立储运发射箱长期储存蠕变的数值分析模型,预测了堆码储存15年后底层发射箱的蠕变变形。以储存后的发射箱作为初始状态建立弹管耦合发射动力学仿真计算模型,进一步分析蠕变对火箭弹发射过程的影响。仿真结果表明:蠕变引起的定向器平行度和发射箱底面平面度的变化均小于技术指标规定值,定向器束的最大残余变形在三维空间内呈马鞍状分布,上、下两行中间位置定向器的变形最大,左、右两列中间位置定向器的变形最小。定向器蠕变变形使得弹管间隙减小,火箭弹在管内运动使弹管之间的动态接触碰撞力增大,离轨速度降低。     

复合材料组合梁的分布参数传递函数法分析模型

应用分布参数传递函数法分析了复合材料组合梁在轴压载荷作用下的振动与稳定性问题。通过引入对偶变量，利用Ｌｅｇｒｅｎｄｒｅ 变换和Ｌａｐｌａｃｅ 变换，建立了可进入Ｈａｍ ｉｌｔｏｎ 体系的混合能量变分原理，并推导出了结构在复频域内的状态空间控制方程， 从而得到了任意边界条件下组合梁振动与稳定性问题的传递函数精确解。分析了一阶和高阶横向剪切变形、转动惯量、细长比、材料各向异性等多种因素对组合梁固有频率和屈曲载荷的影响。文中最后给出了数值算例， 验证了本方法的有效性和适应性。     

韧性材料梁在爆炸载荷作用下的全塑性动态断裂

本文运用刚塑性分析方法,研究了带裂纹韧性材料梁在爆炸载荷作用下的塑性动态断裂过程,建立了简支梁的运动和断裂过程的控制方程。本文考虑了应变率对梁的运动和断裂过程的影响,以及由于断裂引起的附加轴向力对梁的断裂过程的影响,给出了梁的裂纹启裂和上裂的时刻及其条件,以及裂纹扩展长度、裂改扩展速度、断裂截面上弯曲力矩和附加轴向力随时间的变化规律。     

Effect of the end cap on the fragment velocity distribution of a cylindrical cased charge

The prediction of the fragment velocity distribution of a cylindrical cased charge with end caps is one of the key issues to assess the damage efficiency of the warhead. However, limited work has been con-ducted to predict the fragment velocity distributions along the axis of cylindrical cased charges with end caps. This paper presents a study of the velocity distribution of fragments caused by the explosion of a cylindrical cased charge with end caps. The fragment velocity distribution and the end cap velocity were determined by an X-ray radiography method, and the axial fragment distribution was determined by witness plates. It was found that the velocities of fragments, especially near the edge, were increased when the end caps were added, and the position of maximum velocity is closer to the non-detonation end. The fragment velocities were increased, and the fragment projection range was decreased with the increase of the thickness of the end cap. A formula for fragment velocity distributions of a cylindrical cased charge with end caps, which is based on Huang's formula, was proposed by the theoretical analysis and data fitting and validated experimentally. The results indicate that the proposed formula is accurate in predicting the fragment velocity distribution along the axis of a cylindrical cased charge with end caps detonated at one end.     

Experiment and Calculation for Expansion Process of Ablation Plasma Jets in Liquid

The expansion process of ablation plasma jet in liquid was experimentally investigated by using high speed digital camera. The sequential pictures show that, in the initial stage of the jet, the Taylor cavity expands in the axial and radial directions simultaneously, and then, is subjected to the constraint of chamber wall, in axial direction mainly. The maximum axial speed of the cavity's head ranges from 240m/s to 280m/s. Some strong heat conduction and mass transmission effects can be found in the surface of Taylor cavity, where the plasma cools down and condenses as solid particles while the liquid vaporizes as gas. Compared the expansion processes of the cavities among the different discharge energies and the nozzle diameters, it can be seen that the expansion speed of the cavity is directly proportional to the discharge energy and inversely to the nozzle diameter, and the effect of the discharge energy is stronger than that of the nozzle diameter. A set of equations describing the expansion process of ablation plasma jet was derived under the assumption of momentum conservation. The calculated results by use of the equations coincide with the experimented results better.     

圆柱壳在轴向压力作用下的稳定性和振动特性

利用Hamilton原理得出轴向压力作用下圆柱壳位移增量的动力学方程,推导了方程的解析解。通过数值计算,分析了轴向压力作用下圆柱壳的临界屈曲压力随壳体长度变化的曲线,讨论了壳体几何参数(L,h)变化和轴向力幅值变化对振动频率影响的变化曲线。数值计算结果表明,圆柱壳的临界屈曲压力与失稳模态紧密相关;圆柱壳的自振频率随壳体的长度增加而下降,随壳体的厚度增加而提高;圆柱壳的自振频率和最低频率随轴向压力的增大而下降。     

圆柱形装药驱动轴向预制破片飞散特性

为了增强柱形战斗部轴向威力,在无壳柱形战斗部底面布置单层离散的预制破片。开展圆柱形TNT装药驱动轴向预制破片飞散试验,获得预制破片的最大初速、飞散角等特征参数;运用LS-DYNA软件对装药驱动预制破片过程进行数值模拟,阐述预制破片群飞散过程;对装药驱动整体平板理论计算公式进行改进,获得预制破片的最大初速。结果表明:破片初速理论计算结果、数值计算结果和试验结果吻合良好;随着与装药底部中心距离的加大,破片初速、径向飞散角分别近似呈“抛物线”减小、增大;试验实测、理论计算得到的破片最大初速值超过2500 m/s,试验实测的径向飞散角最大约为22°,而周向飞散角则普遍较小,均值在5°以内。     

Growth model of cavity generated by the projectile impacting liquid-filled tank

The high-speed impact of a projectile on a liquid-filled tank causes the hydraulic ram, in which a cavity is formed. To study the growth characteristics of the cavity, the formation mechanism of the cavity is analyzed. The effect of Reynolds number and Mach number on drag coefficient is considered, the axial and radial growth models of the cavity are established respectively. The relative errors between the cavity length calculated by the axial growth model, the cavity diameter calculated by the radial growth model and Ma L. Y. test results are less than 20%, which verifies the effectiveness of the axial and radial growth models. Finally, numerical simulation is carried out to study the growth characteristics of the cavity caused by the projectile impacting the satellite tank at the velocity of 4000 m/s. The cavity length and diameter calculated by the axial and radial growth models agree well with those obtained by simulation results, indicating that the cavity length and diameter in satellite tank can be accurately calculated by the axial and radial growth models.     

脉冲电抗器结构应力测量

为了对高压脉冲放电时电抗器结构受力及电流密度分布规律进行分析,使用电阻应变片对电抗器铜带进行应力测量。利用厚壁筒受压模型对应力测量系统的结果进行计算,设计内置气囊增压法来等效铜带上的应力对测量系统进行标定,并对标定实验数据进行验证。使用半桥补偿电路、屏蔽线及电桥盒共地的方法来减小脉冲电磁干扰及测量回路中寄生电阻和电容带来的电气干扰。实验结果表明:同一测量点处的环向应变峰值比轴向应变峰值大,边缘处的应变大于中心处的,需要在电抗器铜带边缘处加强外包约束。根据应力测量结果推断:铜带边缘处电流密度约为中心处电流密度的1.2倍。