挠性接管在轴对称载荷下的应力应变计算

针对目前挠性接管强度计算存在的不足,在充分考虑骨架层的弯曲刚度和扭转刚度对挠性接管强度影响的基础上,推导出在承受轴对称负荷(拉压、扭矩及内压)时,挠性接管及其加强筋的应变和外力的关系,为挠性接管的结构设计和强度计算提供了理论公式.     

解放战争时期城市接管与公安保卫工作研究

解放战争时期,军队保卫部门除做好军队保卫工作外,还调集和培训大批保卫干部,参与接管新解放城市国民党旧警察机构的工作。当时的接管工作科学、安全、有序,不仅顺利地完成了接管任务,还保证了城市社会管理工作的正常运行。     

弧形体挠性接管声学传递损失计算与分析

为提高弧形体挠性接管的声衰减能力,首先分析了管壁橡胶的粘弹性对其内部介质声速的影响;然后,基于一维声传播理论,推导了弧形体挠性接管的传递损失理论模型,并将理论计算值与有限元分析结果进行了对比;最后,利用弧形体挠性接管传递损失理论公式,分析了弧形体挠性接管结构参数对其传递损失的影响。研究结果表明:弧形体挠性接管内声速随频率增高而递增,以其中心频率为分界点,传递损失曲线分别向低频方向和高频方向移动;弧形体挠性接管传递损失的理论计算与有限元仿真结果在中低频率范围内吻合良好;减小弧形管的壁厚可使其传递损失曲线向低频移动;减小弧形曲率半径能够增大弧形管的传递损失;增加弧形管的长度,可以增加弧形管的传递损失,同时使其传递损失曲线向低频移动。     

1949年中国共产党成功接管南京的历史过程及启示

1949年南京解放前后曾经历了近一年时间的接管期.这一历程可分为"迎接南京解放的斗争"和"全面实施接管"两个阶段.中国共产党对南京的成功接管,具有5个鲜明特点,充分揭示出一致律、结合律、协调律、适应律和互促律等"五律",对当今经济社会发展仍有借鉴意义.     

橡胶挠性接管特性研究

对橡胶挠性接管的静、动态特性进行了研究 .给出了橡胶挠性接管耐压强度的理论计算公式 ,建立了粘弹性管壁管道动态特性数学模型 ,并对方程组进行了求解     

安徽广德：扩权强县给力兴武强兵

2009年,中央“一号文件”明确提出,推进省直接管理县（市）财政体制改革,稳步推进扩权强县（市）改革试点,鼓励有条件的省份率先减少行政层次,依法探索省直接管理县（市）的体制。     

用分布质量分析内燃机连杆动力特性

本文首先分析以传统的两质量替代系统研究连杆动力特性所存在的问题,并用分布质量法分析计算连杆动力特性。最后把两种方法的计算结果进行比较,发现了它们的差异及其原因,肯定了用分布质量分析连杆动力特性比较合理。     

单洞双层隧道围岩力学特性分析

单洞双层隧道作为一种新的隧道形式，不同于分离式隧道和连拱式隧道。利用ANSYS对单洞双层隧道和分离式隧道开挖后围岩的情况进行数值模拟，分析开挖后围岩的应力和位移变化情况、塑性区分布和安全系数，通过对比得出：在浅埋情况下两种隧道围岩应力和位移分布基本一致，地表沉降和分离式隧道相当；单洞双层隧道对围岩扰动深度较大，边墙是其薄弱部位，应力松弛明显，水平位移较大，塑性区水平方向分布较大。     

基于响应平面法的压力容器可靠性评定

针对压力容器制造、使用过程中各种参数的不确定性,提出了一种基于响应平面的随机分析方法.根据某压力容器的结构特点,确定性有限元分析采用了接触有限元,结合中心组合抽样设计构建了容器最大应力的响应平面,以此为基础对压力容器应力分布进行了随机分析.可靠性分析中引入应力—强度干涉模型,并分别对容器壁面和接管处进行了可靠性评定.实...     

国外军民融合发展情况及启示(二)

<正>三、区域整合:英、法、德的一体化尝试欧洲是两次世界大战的发源地,军工生产不乏强劲动力,冷战时期很多国家不惜以政府接管方式加快军工发展。到20世纪80年代初,西欧武器生产能力过剩问题严重,英、法、德、意、西班牙等开始出售国营军工企业,想通过此举实现扭亏为盈。英国是西方阵营的第二军事强国。其国防工业体系一大特点,就是直到20世纪60-70年代,多数军工企业都是国有企业,缺乏市场竞争,技术、财政风险全     

成层地基中压入法沉桩引起的桩周土体变形分析

通过在桩-土界面设置接触面,选用合理的单元类型,建立了较为符合压入桩压桩实际的三维有限元模型。利用得到的有限元模型,采用单元生死技术对压入桩压桩过程进行了数值模拟,讨论了成层地基压桩过程中桩周土体的竖向应力及应变随压桩深度的动态变化。选用桩型为钢管桩,分析结果表明:随着压桩深度的增加,桩内桩周土体的竖向应力(或应变)一直表现为压应力(或压应变),且逐渐增大;桩外桩周土体的竖向应力(或应变)逐渐由压应力(或压应变)变为拉应力(或拉应变)。随着压桩深度的增加,桩内桩周土体前3层竖向应力(或应变)的变化幅度基本一致,第4层的变化幅度增大;桩外桩周土体每2层土之间的差异都较大。     

加肋凹锥-环-柱结合壳结构参数分析

采用分区样条等参元法,分析了加肋凹锥 环 柱结合壳的应力和稳定性特点,研究了各项结构参数变化对结合壳应力和稳定性的影响,认为加肋凹锥 环 柱结合壳能有效降低锥柱结合部的纵向弯曲应力,但对于降低环向应力效果有限,建议在环壳段中部增加一档肋骨;半锥角的凹结合壳越大,嵌入环壳段的优势越明显;增大环壳与柱壳半径比可以有效降低环壳段中部的纵向弯曲应力.     

Equivalent accelerated life testing plans for log‐location‐scale distributions

Accelerated life testing (ALT) is widely used to determine the failure time distribution of a product and the associated life‐stress relationship in order to predict the product's reliability under normal operating conditions. Many types of stress loadings such as constant‐stress, step‐stress and cyclic‐stress can be utilized when conducting ALT. Extensive research has been conducted on the analysis of ALT data obtained under a specified stress loading. However, the equivalency of ALT experiments involving different stress loadings has not been investigated. In this article, a log‐location‐scale distribution under Type I censoring is considered in planning ALT. An idea is provided for the equivalency of various ALT plans involving different stress loadings. Based on this idea, general equivalent ALT plans and some special types of equivalent ALT plans are explored. For demonstration, a constant‐stress ALT and a ramp‐stress ALT for miniature lamps are presented and their equivalency is investigated. © 2010 Wiley Periodicals, Inc. Naval Research Logistics, 2010     

Comparison between constant‐stress and step‐stress accelerated life tests under Time Constraint

By running life tests at higher stress levels than normal operating conditions, accelerated life testing (ALT) quickly yields information on the lifetime distribution of a test unit. The lifetime at the design stress is then estimated through extrapolation using a regression model. In constant‐stress testing, a unit is tested at a fixed stress level until failure or the termination time point of test, whereas step‐stress testing allows the experimenter to gradually increase the stress levels at some prefixed time points during the test. In this work, the optimal k‐level constant‐stress and step‐stress ALTs are compared for the exponential failure data under complete sampling and Type‐I censoring. The objective is to quantify the advantage of using the step‐stress testing relative to the constant‐stress one. Assuming a log‐linear life–stress relationship with the cumulative exposure model for the effect of changing stress in step‐stress testing, the optimal design points are determined under C/D/A‐optimality criteria. The efficiency of step‐stress testing to constant‐stress one is then discussed in terms of the ratio of optimal objective functions based on the information matrix. © 2013 Wiley Periodicals, Inc. Naval Research Logistics 00: 000–000, 2013     

无约束自由体有限元分析中的准静态法

在对某水下无约束航行体进行有限元静力分析的时候,由于无法限定结构的自由度而使刚度矩阵奇异,从而导致求解失败。为了解决这一问题,采用强迫约束法和准静态法(惯性释放)对此航行体进行了有限元静力对比计算,结果表明:用强迫约束法对水下航行体进行静力分析时,在施加强迫约束的部位出现了严重的应力集中现象,应力最大值为1.25×106Pa,应力集中使得整个结构的应力分布与实验数据相差较大,可认为计算结果错误;采用惯性释放法对其进行静力分析时,应力最大值为3.27×105Pa,整个结构的应力分布合理,与实验数据一致,计算结果正确。     

Reliability inference for field conditions from accelerated degradation testing

Accelerated degradation testing (ADT) is usually conducted under deterministic stresses such as constant‐stress, step‐stress, and cyclic‐stress. Based on ADT data, an ADT model is developed to predict reliability under normal (field) operating conditions. In engineering applications, the “standard” approach for reliability prediction assumes that the normal operating conditions are deterministic or simply uses the mean values of the stresses while ignoring their variability. Such an approach may lead to significant prediction errors. In this paper, we extend an ADT model obtained from constant‐stress ADT experiments to predict field reliability by considering the stress variations. A case study is provided to demonstrate the proposed statistical inference procedure. The accuracy of the procedure is verified by simulation using various distributions of field stresses. © 2006 Wiley Periodicals, Inc. Naval Research Logistics, 2006.     

Statistical equivalency and optimality of simple step‐stress accelerated test plans for the exponential distribution

Accelerated life testing (ALT) is commonly used to obtain reliability information about a product in a timely manner. Several stress loading designs have been proposed and recent research interests have emerged concerning the development of equivalent ALT plans. Step‐stress ALT (SSALT) is one of the most commonly used stress loadings because it usually shortens the test duration and reduces the number of required test units. This article considers two fundamental questions when designing a SSALT and provides formal proofs in answer to each. Namely: (1) can a simple SSALT be designed so that it is equivalent to other stress loading designs? (2) when optimizing a multilevel SSALT, does it degenerate to a simple SSALT plan? The answers to both queries, under certain reasonable model assumptions, are shown to be a qualified YES. In addition, we provide an argument to support the rationale of a common practice in designing a SSALT, that is, setting the higher stress level as high as possible in a SSALT plan. © 2012 Wiley Periodicals, Inc. Naval Research Logistics, 2013     

921A钢在海水中腐蚀的力学化学效应

为了研究弹性应力和弹塑性应变对921A船体钢在模拟海水中腐蚀行为的影响,采用自制的载荷-电化学实验装置对921A钢在载荷与腐蚀介质协同作用时的开路电位、动电位极化曲线和电化学阻抗谱等电化学性能进行了测试,并由电化学阻抗谱拟合得到的电荷传递电阻定义载荷下的腐蚀速率修正因子,将实验得到的腐蚀速率修正因子与理论值进行了对比。结果表明:弹性拉应力与弹性压应力对力学化学效应的影响具有对称性。力学化学效应随着弹性应力的增大而增大,随着弹塑性应变的增大先增大后减小。弹塑性应变对力学化学效应的影响远远大于弹性应力的影响。在研究范围内,弹塑性应变引起的腐蚀电位负移量最大为62.6 mV,相应的腐蚀速率修正因子高达4.113,而弹性应力引起的腐蚀电位负移量最大为24.5 mV,相应的腐蚀速率修正因子为1.746。由此可见,应力应变对921A钢在海水中腐蚀行为的影响不容忽视。     

超声冲击处理改善22SiMn2TiB装甲钢抗应力腐蚀性能研究

采用超声冲击处理工艺对22SiMn2TiB装甲钢试样进行了表面冲击强化,采用四点弯曲加载装置将处理和未处理的试样在3.5%NaCl溶液中进行了150 d的应力腐蚀试验。用X射线应力测定仪测定了应力腐蚀试验前试样表面的残余应力,用扫描电镜和透射电镜观察了处理后试样的断面组织。分析了超声冲击处理引起的残余应力和断面组织变化对改善装甲钢抗应力腐蚀性能的作用。结果表明,超声冲击处理引入的残余压应力和表层晶粒细化可以大大提高22SiMn2TiB装甲钢的抗应力腐蚀性能。     

舰炮大型铸铝件断裂残余应力分析

采用盲孔法测试某型舰炮大型铸铝件残余应力,结果分析表明原结构中残余应力较大,部分位置残余应力超过材料屈服极限是其断裂的根本原因.通过工艺改进后,构件残余应力幅值大幅降低,满足工程要求.