聚乙二醇对纳米SiO2水悬浮液分散稳定性的影响

通过沉降试验主要研究了聚乙二醇对纳米SiO2水悬浮液分散稳定性的影响,研究发现聚乙二醇的分子量和含量、悬浮液的pH值及超声分散功率、所含电解质的浓度对纳米SiO2水悬浮液的分散稳定性都有显著影响.红外光谱分析表明聚乙二醇是以氢键吸附在纳米SiO2颗粒表面,2者并没有发生化学反应.     

高官能度水性聚氨酯丙烯酸酯/纳米SiO2杂化材料的制备及性能

以聚己内酯二醇(PCL)、异佛尔酮二异氰酸酯(IPDI)、二羟甲基丙酸(DMPA)和季戊四醇三丙烯酸酯(PETA)为原料,合成了高官能度水性聚氨酯丙烯酸酯WPUA。以WPUA为有机相,γ-甲基丙烯酰氧丙基三甲氧基硅烷(TMSPM)改性纳米SiO2为无机相,制备了水性光固化有机/无机纳米杂化体系。通过傅立叶变换红外光谱对合成产物进行了表征,并对杂化薄膜的表面形貌、热稳定性、光固化动力学及力学性能进行了分析。结果表明合成了预期产物,杂化体系中改性纳米SiO2分散均匀稳定;随着SiO2含量的增加,材料的热稳定性、力学性能均有明显提高;不同SiO2条件下体系均保持了较高的光固化速率和最终凝胶含量。     

油溶性纳米ZnS粒子的制备、表征及在油品中的分散稳定性

采用均匀沉淀法制备硬脂酸修饰的纳米ZnS粒子,用扫描电子显微镜、红外光谱仪和热分析仪对其结构进行了表面分析,通过离心试验考查在基础油中的分散稳定性.结果表明硬脂酸修饰的纳米ZnS粒子粒径在20～50 nm之间,且分布均匀;表面修饰剂与纳米粒子之间发生了化学反应,从而使得纳米粒子在基础油中具有优良的分散稳定性.作为油品添加剂,硬脂酸对纳米ZnS粒子的最佳修饰比例为21(物质的量比).     

非均匀形核法制备Cu包覆纳米SiO2复合粉体

采用非均匀形核法制备了Cu包覆纳米SiO2复合颗粒,利用X射线衍射仪、扫描电镜、能谱仪及透射电镜等分析手段对复合颗粒进行了表征,并探讨了包覆结构的形成机制。结果表明:复合颗粒分散均匀,无团聚,单颗粒内包含多个分布均匀的纳米SiO2颗粒,且均被Cu包覆层隔离,纳米SiO2颗粒的分散性得到了显著改善;新制备的复合颗粒不存在氧化,在存放或者制样过程中会部分氧化为Cu2O;纳米SiO2颗粒表面Cu包覆层的形成机制主要是非均匀形核作用,包覆的结构取决于 Cu晶粒在纳米SiO2颗粒表面的沉积以及对复合颗粒的团聚控制。     

纳米SiO_2增韧改性环氧乙烯基酯树脂的性能研究

为了对环氧乙烯基酯树脂(EVER)进行增韧改性,采用KH570硅烷偶联剂对纳米SiO2进行表面处理,考察了纳米SiO2表面改性及其质量分数对EVER力学性能的影响。经过偶联剂处理的纳米SiO2复合材料在树脂基体中具备更好的分散性和相容性,力学性能明显优于纯EVER材料和未经偶联剂处理的复合材料。纳米SiO2质量分数为3%时,纳米SiO2复合材料的拉伸强度、断裂伸长率、冲击强度分别比纯EVER材料提高了42.10%,43.38%和91.91%;纳米SiO2质量分数为4%时,纳米SiO2复合材料的拉伸模量比纯EVER材料提高了34.57%。通过观察冲击断面的SEM照片,分析了纳米SiO2增韧改性的作用机理。结果表明:纳米SiO2增韧改性的关键在于诱发基体产生银纹,使其对裂纹扩展起到钝化、阻碍的作用。     

纳米Fe_3O_4磁性流体的制备与测试

采用化学共沉淀法制备Fe_3O_4磁性纳米颗粒,用油酸作为分散剂制备出煤油基和二脂基磁性流体.用X射线荧光光谱仪(XRF)、X射线衍射(XRD)测试分析颗粒的组成、结构、平均粒径,表明所制备的颗粒为纯净Fe_3O_4纳米粒子,其平均粒径小于15 nm,分布均匀.用傅立叶变换红外光谱仪(FTIR)、热重法(TGA) 和导数热重量(DTG)分析法对磁性流体进行性能测试,结果表明磁性流体进行性能稳定,煤油基磁性流体工作温度应低于88.6 ℃,二脂基磁性流体的应低于236.0 ℃.     

纳米SiO2颗粒增强铜基复合材料性能研究

以纳米SiO2颗粒为增强体,采用粉末冶金法制备铜基纳米复合材料.考察不同质量分数的纳米颗粒对复合材料密度、硬度以及摩擦磨损性能的影响.结果表明纳米SiO2颗粒的加入,使铜基体的硬度和摩擦磨损性能都得到了明显提高;但随着纳米SiO2质量分数的增加,复合材料的密度和硬度均呈下降趋势;当纳米SiO2质量分数为0.3 %时,复合材料的减摩耐磨性最好.     

一种新型甲醛气体清除材料的实验研究

采用溶胶-凝胶法将纳米TiO2负载在活性碳纤维上,制备出一种新型甲醛气体清除材料。在制备中依次掺杂Fe3+和十二烷基苯磺酸钠(SDBS)对纳米TiO2进行改性,研究了纳米TiO2光催化活性的变化,并测试了自制材料的甲醛清除效率。结果表明:Fe3+和SDBS的添加不会改变纳米TiO2的晶型结构,但有利于晶粒的成长和负载膜的光催化活性;添加体积分数分别为0.8%的Fe3+和3%的SDBS时,材料的甲醛清除效率最高。     

纳米SiO2形态对铜基摩擦材料摩擦学性能的影响

采用粉末冶金法分别制备了添加0.75 wt%的纳米SiO2(n-SiO2)和0.75 wt%Cu包纳米SiO2(Cu/n-SiO2)复合粉体的新型铜基摩擦材料.采用惯性台架试验机,研究比较了2种材料与未添加纳米SiO2的材料的摩擦学性能.结果表明添加0.75 wt% Cu/n-SiO2的铜基摩擦材料,耐热性提高了32%,摩擦因数更稳定,耐磨性提高了2.02倍.经铜包覆处理后的n-SiO2对材料性能的影响优于未处理的n-SiO2.     

InSb纳米颗粒的制备与原子力显微镜

为进一步研究半导体纳米材料的物理特性,用真空沉积的方法在SiO2基片上制备了纳米InSb颗粒膜。用原子力显微镜扫描样品表面的分析显示,纳米InSb颗粒均匀地分布在SiO2基片表面。实验结果表明通过改变镀膜时间,可以得到具有不同颗粒尺寸的InSb纳米颗粒。     

悬浮固相颗粒对储集层基质孔隙的堵塞规律研究

应用胜利油区8个不同区块的岩心及注入水,采用岩心流动实验手段,研究了注入水中悬浮颗粒对储层孔隙的堵塞特征,发现悬浮颗粒对储层的堵塞特征表现为孔隙逐步堵塞和迅速堵塞两种类型;悬浮颗粒浓度低且孔径与粒径的比值较大时易形成孔隙避步堵塞;悬浮颗粒浓度大或孔径与粒径的比值较小时易形成迅速堵塞;悬浮颗粒对储层的堵塞程度、堵塞类型是颗粒浓度、颗粒粒径与储层孔喉匹配综合作用的结果;迅速堵塞特征的初始堵塞效果主要取决于孔径与粒径的匹配关系,最终堵塞效果主要与注入水中的颗粒浓度有关;高浓度的小颗粒对孔隙基质的堵塞特征表现为迅速堵塞。     

纳米SiO_2在润滑油中的高温摩擦学性能

采用多功能SRV试验机考察了纳米SiO2在菜籽油中的高温摩擦学性能,利用表面轮廓仪观察磨损表面形貌。结果表明,在恒定负荷试验中,纳米SiO2能明显改善菜籽油的高温减摩抗磨性能,在500℃时,摩擦因数仅为0.16,磨损量降低了80%以上。在连续加载的高温试验中,当试验温度为200℃时,纳米SiO2对菜籽油的减摩抗磨性能没有明显的改善;而当试验温度达到500℃时,纳米SiO2能明显地改善菜籽油的减摩抗磨性能,在大负荷(500N)的情况下更为突出。     

粉末粒度对储氢电极电化学性能的影响

以M1（NiCoMnTi）5为例,系统研究了粉末粒度对储氢电极电化学性能的影响。结果表明,在试验粒度范围内,合金粉越细,其放电容量越高,高倍率放电性能和循环稳定性也越好;将两种不同粒度的合金粉混合使用时,粒径相差越大,其放电容量越高。且当粗细粉质量比为7：3时,放电容量最高。     

无电焊接材料的燃烧速度和燃烧温度研究

采用高放热性的铝热剂（CuO＋Al）并加入适当的添加剂,制备了便携式的无电焊接笔材料,其燃烧速度可控,且具有高的燃烧温度。研究了反应剂颗粒大小、混料均匀性等对无电焊接笔材料的燃烧性能的影响。结果表明：反应剂粒径对无电焊接笔的燃烧速度具有显著影响,随着反应剂粒径的增大,燃烧速度明显减慢。反应剂粒径和混料时间是影响单位时间放热量和混料均匀度的主要因素,因而对无电焊接笔的燃烧温度具有明显影响。在一定的混料时间下,反应物粉末具有最佳的混料均匀性。反应物粒径小且混料均匀性好的无电焊接笔材料,其燃烧温度高。     

The effect of al particle size on thermal decomposition,mechanical strength and sensitivity of Al/ZrH2/PTFE composite

To study the thermal decomposition of Al/ZrH2/PTFE with different Al particle size as well as mechanical strength and impact sensitivity under medium and low strain rates, molding-vacuum sintering was adopted to prepare four groups of power materials and cylindrical specimens with different Al particle size. The active decomposition temperature of ZrH2 was obtained by TG-DSC, and the quasi-static me-chanics/reaction characteristics as well as the impact sensitivity of the specimen were studied respec-tively by quasi-static compression and drop-hammer test. The results show that the yield strength of the material decreased with the increase of the Al particle size, while the compressive strength, failure strain and toughness increased first and then decreased, which reached the maximum values of 116.61 MPa, 191％, and 119.9 MJ/m respectively when the Al particle size is 12—14μm because of particle size grading. The specimens with the highest strength and toughness formed circumferential open cracks and reacted partly when pressed. Those with developmental cracks formed inside did not react. It is considered that fracture of specimens first triggered initial reaction between Al and PTFE to release an amount of heat. Then ZrH2 was activated and decomposed, and participated in subsequent reaction to generate ZrC. The impact sensitivity of the specimens decreased with the increase of Al particle size.     

粉末燃料冲压发动机内镁粉尘云层流燃烧模型

对粉末燃料冲压发动机预燃室内镁粉尘云燃烧过程进行了研究,建立了镁粉尘云的一维层流预混燃烧模型。研究表明,镁粉尘云层流火焰传播很稳定,燃烧过程中火焰结构基本不变,燃烧区很薄,而预热区厚度约是燃烧区的2-3倍。粉尘云中镁颗粒的蒸发和气相镁与氧气的均相反应是产生火焰的直接原因,也是火焰得以传播的关键。预热区气相温度升高主要靠燃烧区气体的导热和扩散过来的气相镁与氧气反应释放热量,而预热区颗粒相温度升高主要靠气相对其对流传热。分析了各参数对粉尘云燃烧的影响,颗粒相对浓度对粉尘云燃烧的影响比较复杂,在浓度较低的情况下,增大颗粒相对浓度有利于粉尘云快速燃烧;而在浓度较高的情况下,增大颗粒相对浓度则不利于粉尘云快速燃烧。随颗粒粒径的增加,火焰传播速度减小,火焰温度升高,预热区厚度增大。火焰传播速度和火焰温度随粉尘云初温增加线性增长,预热区厚度随粉尘云初温增加抛物线增长。数值模拟与文献中试验结果的变化趋势相一致。     

基于磁流变阻尼器的车辆悬挂二自由度模型控制算法

将磁流变(MRF)新型阻尼减振器用于车辆悬挂减振系统中,用以实现变阻尼式履带车辆悬挂系统半主动控制。在基于线性二次型最优控制理论(LQR法)的基础上,对车辆悬挂系统的半主动控制算法进行了深入研究,建立了二自由度1/4车体的动力学模型,并对其控制效果进行了仿真,结果表明这种半主动控制算法对车辆悬挂系统的半主动有着很好的效果。     

球磨时间对纳米SiO_2/Cu复合材料摩擦学性能的影响

采用球磨法与热压烧结工艺制备了添加w（n-SiO2）=1.0%的铜基纳米复合材料。通过球盘式摩擦磨损试验机测试了复合材料的摩擦磨损性能,采用排水法和场发射扫描电镜（FSEM）研究了复合材料的致密度、显微组织和磨损形貌。结果表明：球磨可提高复合材料的致密度,改善n-SiO2在铜基体中的分散均匀性;随球磨时间的增加,复合材料的动摩擦因数和磨损量先减小后增加,球磨10 h复合材料具有较低的摩擦因数和磨损量,磨损机理主要为磨料磨损。     

Effect of tool rotational speed on the particle distribution in friction stir welding of AA6092/17.5 SiCp-T6 composite plates and its consequences on the mechanical property of the joint

This study investigates the effect of tool rotational speed (TRS) on particle distribution in nugget zone (NZ) through quantitative approach and its consequences on the mechanical property of friction stir welded joints of AA6092/17.5 SiC_p-T6 composite. 6 mm thick plates are welded at a constant tool tilt angle of 2° and tool traverse speed of 1 mm/s by varying the TRS at 1000 rpm, 1500 rpm and 2000 rpm with a taper pin profiled tool. Microstructure analysis shows large quantity of uniformly shaped smaller size SiC particle with lower average particle area which are homogeneously distributed in the NZ. The fragmentation of bigger size particles has been observed because of abrading action of the hard tool and resulting shearing effect and severe stress generation due to the rotation of tool. The particles occupy maximum area in the matrix compared to that of the base material (BM) due to the redistribution of broken particles as an effect of TRS. The migration of particles towards the TMAZ-NZ transition zone has been also encountered at higher TRS (2000 rpm). The microhardness analysis depicts variation in average hardness from top to bottom of the NZ, minimum for 1500 rpm and maximum for 2000 rpm. The impact strength at 1000 rpm and 1500 rpm remains close to that of BM (21.6 J) while 2000 rpm shows the accountable reduction. The maximum joint efficiency has been achieved at 1500 rpm (84%) and minimum at 1000 rpm (68%) under tensile loading. Fractographic analysis shows mixed mode of failure for BM, 1000 rpm and 1500 rpm, whereas 2000 rpm shows the brittle mode of failure.     

Combustion of B4C/KNO3 binary pyrotechnic system

Presented herein is an experimental study on the combustion of B4C/KNO3 binary pyrotechnic system.Combustion products were tested using X-ray diffraction(XRD),scanning electron microscopy(SEM),and energy dispersive spectrometer(EDS).According to the results of tests and CEA calculation,the combustion reaction equation was established.The flames and burning rates were recorded by a high speed camera and a spectrophotometer.The effect of B4C particle size on the thermal sensitivity of B4C/KNO3 was investigated by differential scanning calorimetry(DSC)techniques.In addition,a reliable method for calculating the flame temperature was proposed.Based on the results of experiments,the combustion reaction mechanism was briefly analyzed.The burning rate,flame temperature and thermal sensitivity of B4C/KNC3 increase with the decrease of B4C particle size.The mass ratio of B4C/KNO3 has a great effect on combustion properties.Oxidizer-rich compositions have low flame temperatures,low burning rates,and provide green light emission.The combustion reactions of fuel-rich compositions are vigorous,and the B4C/KNO3 with mass ratio of 25:75 has the highest burning rate and the highest flame temperature.