A study on the surface overpressure distribution and formation of a double curvature liner under a two-point initiation

The formation mechanism of an EFP(explosively formed projectile) using a double curvature liner under the overpressure effect generated by a regular oblique reflection was investigated in this paper.Based on the detonation wave propagation theory,the change of the incident angle of the detonation wave collision at different positions and the distribution area of the overpressure on the surface of the liner were calculated.Three-dimensional numerical simulations of the formation process of the EFP with tail as well as the ability to penetrate 45# steel were performed using LS-DYNA software,and the EFP ve-locity,the penetration ability,and the forming were assessed via experiments and x-ray photographs.The experimental results coincides with those of the simulations.Results indicate that the collision of the detonation wave was controlled to be a regular oblique reflection acting on the liner by setting the di-mensions of the unit charge and maintaining the pressure at the collision point region at more than 2.4 times the CJ detonation when the incident angle approached the critical angle.The distance from the liner midline to the boundary of the area within which the pressure ratio of the regular oblique reflection pressure to the CJ detonation pressure was greater than 2.5,2,and 1.5was approximately 0.66 mm,1.32 mm,and 3.3 mm,respectively.It is noted that pressure gradient caused the liner to turn inside out in the middle to form the head of the EFP and close the two tails of the EFP at approximately 120μs.The penetration depth of the EFP into a 45# steel target exceeded 30 mm,and there was radial expansion between the head and tail of the EFE increasing the penetration resistance of the EFP.Therefore,the structural size of the unit charge and the liner can be further optimized to reduce resistance to increase the penetration ability of the EFP.     

Reaction degree of composition B explosive with multi-layered compound structure protection subjected to detonation loading

The explosive reaction degree and protection from explosions are concerns in the military field.In this work,the reaction degree of the composition B explosive was investigated experimentally.Multi-layered compound structures were used as barriers to weaken the blast loads.A comprehensive experiment using a high-speed camera and image processing techniques,side witness plates,and bottom witness plates was presented.Using the experimental fragment velocities,fragment piercing patterns,and damage characteristics,the reaction degree of the explosive impeded by different multi-layered com-pound structures could be precisely differentiated.Reaction parameters of the explosive obstructed by compound structures were obtained by theoretical analysis and numerical simulations.Unlike the common method in which the explosive reaction degree is only distinguished based on the initial pressure amplitude transmitted into the explosive,a following shock wave reflected from the side steel casing was also considered.Different detonation growth paths in the explosive formed.Therefore,all these shock wave propagation characteristics must be considered to analyze the explosive response impeded by compound structures.     

Effect of wave shaper on reactive materials jet formation and its penetration performance

Wave shaper effect on formation behavior and penetration performance of reactive liner shaped charge (RLSC) are investigated by experiments and simulations. The reactive materials liner with a density of 2.3 g/cm³ is fabricated by cold pressing at a pressure of 300 MPa and sintering at a temperature of 380 °C. Experiments of the RLSC with and without wave shaper against steel plates are carried out at standoffs of 0.5, 1.0, and 1.5 CD (charge diameter), respectively. The experimental results show that the penetration depths and structural damage effects of steel plates decrease with increasing the standoff, while the penetration depths and the damage effects of RLSC without wave shaper are much greater than that with wave shaper at the same standoff. To understand the unusual experimental results, numerical simulations based on AUTODYN-2D code are conducted to discuss the wave shaper effect, including the propagation behavior of detonation wave, the velocity and temperature distribution of reactive jet, and penetration depth of reactive jet. The simulations indicate that, compared with RLSC without wave shaper, there is a higher temperature produced inside reactive jet with wave shaper. This unusual temperature rise effects are likely to be an important mechanism to cause the initiation delay time of reactive jet to decline, which results in significantly decreasing its penetration performance.     

驱动管中柱状装药爆轰过程的数值模拟

数值模拟了爆炸驱动管中柱状装药内爆轰波的传播过程.计算采用欧拉型有限体积方法,炸药及爆轰产物均采用JWL状态方程,空气采用理想气体状态方程,采用"点火-生长"模型计算化学反应速率.计算得到了驱动管内波系结构的发展过程,爆速与经验公式符合得较好.计算表明,驱动管侧壁的压力峰值在800MPa以上,而在管底中心处,由于激波的汇聚,压力峰值高达12.4GPa.     

Fracture mechanism of a cylindrical shell cut by circumferential detonation collision

The failure mechanism of a cylindrical shell cut into fragments by circumferential detonation collision was experimentally and numerically investigated. A self-designed detonation wave regulator was used to control the detonation and cut the shell. It was found that the self-designed regulator controlled the fragment shape. The macrostructure and micro-characteristics of fragments revealed that shear fracture was a prior mechanism, the shell fractured not only at the position of detonation collision, but the crack also penetrated the shell at the first contact position of the Chapmen-Jouguet (C-J) wave. The effects of groove number and outer layer thickness on the fracture behavior were tested by simulations. When the thickness of the outer layer was 5–18 mm, it has little effect on fragmentation of the shell, and shells all fractured at similar positions. The increase of the groove number reduced the fracture possibility of the first contact position of the C-J wave. When the groove number reached 7 with a 10 mm outer layer (1/4 model), the fracture only occurred at the position of detonation collision and the fragment width rebounded.     

强脉冲 CO2 激光与靶的相互作用

在真空背景下的实验表明,当微秒量级的强脉冲激光与靶材相互作用时,由于靶材的升华,激光维持爆震波依然存在。爆震波产生的压缩波传入靶内,该应力波的作用是材料破坏的重要因素。而强脉冲激光引起的汽化反冲压力、热应力和烧蚀破坏也是不可忽视的因素。实验还表明,在真空背景下维持爆震波足以将后续激光屏蔽。     

Effects of total pressures and equivalence ratios on kerosene/air rotating detonation engines using a paralleling CE/SE method

In this paper, the kerosene/air rotating detonation engines(RDE) are numerically investigated, and the emphasis is laid on the effects of total pressures and equivalence ratios on the operation characteristics of RDE including the initiation, instabilities, and propulsive performance. A hybrid MPI + OpenMP parallel computing model is applied and it is proved to be able to obtain a more effective parallel performance on high performance computing(HPC) systems. A series of cases with the total pressure of 1 MPa, 1.5 MPa, 2 MPa, and the equivalence ratio of 0.9, 1, 1.4 are simulated. On one hand, the total pressure shows a significant impact on the instabilities of rotating detonation waves. The instability phenomenon is observed in cases with low total pressure (1 MPa) and weakened with the increase of the total pressure. The total pressure has a small impact on the detonation wave velocity and the specific impulse. On the other hand, the equivalence ratio shows a negligible influence on the instabilities, while it affects the ignition process and accounts for the detonation velocity deficit. It is more difficult to initiate rotating detonation waves directly in the lean fuel operation condition. Little difference was observed in the thrust with different equivalence ratios of 0.9, 1, and 1.4. The highest specific impulse was obtained in the lean fuel cases, which is around 2700 s. The findings could provide insights into the understanding of the operation characteristics of kerosene/air RDE.     

两道同侧扫掠激波作用下形成的三维平板边界层

为探索一种减弱扫掠激波/边界层干扰强度的侧压方式,采用数值计算方法研究两道同侧扫掠激波作用下形成的三维平板边界层。对三维边界层的流动机理进行研究,并与相同气流偏转角的一道扫掠激波作用下形成的三维边界层进行定量比较。研究表明,存在两道同侧扫掠激波时,第一道扫掠激波使侧壁附近边界层变薄,进而使第二道扫掠激波与再附形成的边界层的相互作用减弱,从而总的效果是两道扫掠激波与边界层的相互作用强度比一道扫掠激波的弱;两道扫掠激波的气流总偏转角与一道扫掠激波的相同,相交后汇聚成的激波强度与一道扫掠激波的基本相同,之前被两道扫掠激波"扫"起来的边界层在汇聚激波作用下还呈现锥形流动,分离线和来流的夹角也与一道扫掠激波的基本相同。     

Application of Two-dimensional Viscous CE/SE Method in Calculation of Two-phase Detonation

The method of two-dimensional viscous space-time conservation element and solution element (CE/SE) can be used to calculate the gas-liquid two-phase interior flow field in pulse detonation engine (PDE). In this paper, the evolution of the detonation wave and the distribution of its physical parameters were analyzed. The numerical results show that the change of axial velocity of gas is the same as that of detonation pressure. The larger the liquid droplet radius is, the longer the time to get stable detonation wave is. The calculated results coincide with the experimented results better.     

1D study of the detonation phenomenon and its influence on the interior ballistics of the combustion light gas gun

One-dimensional simulations with a detailed hydrogen-oxygen reaction mechanism have been performed to investigate detonation phenomenon in a combustion light gas gun (CLGG). Convection fluxes of the Navier-Stokes equations are solved using the WAF (weighted average flux) scheme HLLC Riemann solver. A high resolution fifth-order WENO scheme for the variable extrapolation at the volume interface and a fourth-order Runge-Kutta scheme for the time advancement are used. Validation tests of the stoichiometric hydrogen-oxygen deflagration to detonation transition process shows good agreement between the computed results and the analytical and documented solutions, demonstrating the reliability on the detonation simulation of the current scheme. Simulation results of the interior ballistic process of the CLGG show that the flame propagation experiences three distinct stages. The blast detonation wave causes a high-pressure shock and hazardous oscillations in the chamber and makes the projectile accelerate with fluctuations, but has only a small improvement to the muzzle velocity.     

Influence of propagation direction on operation performance of rotating detonation combustor with turbine guide vane

Due to the pressure gain combustion characteristics, the rotating detonation combustor (RDC) can enhance thermodynamic cycle efficiency. Therefore, the performance of gas-turbine engine can be further improved with this combustion technology. In the present study, the RDC operation performance with a turbine guide vane (TGV) is experimentally investigated. Hydrogen and air are used as propellants while hydrogen and air mass flow rate are about 16.1 g/s and 500 g/s and the equivalence ratio is about 1.0. A pre-detonator is used to ignite the mixture. High-frequency dynamic pressure transducers and silicon pressure sensors are employed to measure pressure oscillations and static pressure in the combustion chamber. The experimental results show that the steady propagation of rotating detonation wave (RDW) is observed in the combustion chamber and the mean propagation velocity is above 1650 m/s, reaching over 84% of theoretical Chapman-Jouguet detonation velocity. Clockwise and counterclockwise propagation directions of RDW are obtained. For clockwise propagation direction, the static pressure is about 15% higher in the combustor compared with counterclockwise propagation direction, but the RDW dominant frequency is lower. When the oblique shock wave propagates across the TGV, the pressure oscillations reduces significantly. In addition, as the detonation products flow through the TGV, the static pressure drops up to 32% and 43% for clockwise and counterclockwise propagation process respectively.     

Effects of nano-sized aluminum on detonation characteristics and metal acceleration for RDX-based aluminized explosive

Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the param-eters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0％to 15％,every 5％increase of aluminum resulted in about a 1.3％decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14％and 8％higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 μs throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12％and 2.9 μs higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80％of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.     

Analysis on damage characteristics and detonation performance of solid rocket engine charge subjected to jet

To further explore the damage characteristics and impact response of the shaped charge to the solid rocket engine (SRE) in storage or transportation, protective armor was designed and the shelled charges model (SCM)/SRE with protective armor impacting by shaped charge tests were conducted. Air overpressures at 5 locations and axial acceleration caused by the explosion were measured, and the experimental results were compared with two air overpressure curves of propellant detonation obtained by related scholars. Afterwards, the finite element software AUTODYN was used to simulate the SCM impacted process and SRE detonation results. The penetration process and the formation cause of damage were analyzed. The detonation performance of TNT, reference propellant, and the propellant used in this experiment was compared. The axial acceleration caused by the explosion was also analyzed. By comprehensive comparison, the energy released by the detonation of this propellant is larger, and the HMX or Al particles contained in this propellant are more than the reference propellant, with a TNT equivalent of 1.168–1.196. Finally, advanced protection armor suggestions were proposed based on the theory of woven fabric rubber composite armor (WFRCA).     

Chain damage effects of multi-spaced plates by reactive jet impact

Chain damage is a new phenomenon that occurs when a reactive jet impacts and penetrates multi-spaced plates.The reactive jet produces mechanical perforations on the spaced plates by its kinetic energy(KE),and then results in unusual chain rupturing effects and excessive structural damage on the spaced plates by its deflagration reaction.In the present study,the chain damage behavior is initially demonstrated by experiments.The reactive liners,composed of 26 wt％Al and 74 wt％PTFE,are fabricated through a pressing and sintering process.Three reactive liner thicknesses of 0.08 CD,0.10 CD and 0.12 CD(charge diameter)are chosen to carry out the chain damage experiments.The results show a chain rupturing phenomenon caused by reactive jet.The constant reaction delay time and the different penetration velocities of reactive jets from liners with different thicknesses result in the variation of the deflagration position,which consequently determines the number of ruptured plates behind the armor.Then,the finite-element code AUTODYN-3D has been used to simulate the kinetic energy only-induced rupturing effects on plates,based on the mechanism of behind armor debris(BAD).The significant discrepancies between simulations and experiments indicate that one enhanced damage mechanism,the behind armor blast(BAB),has acted on the ruptured plates.Finally,a theoretical model is used to consider the BAB-induced enhancement,and the analysis shows that the rupturing area on aluminum plates depends strongly upon the KE only-induced pre-perforations,the mass of reactive materials,and the thickness of plates.     

管道超声导波无损检测技术应用研究

利用研制的磁致伸缩超声导波无损检测装置对长直无缝钢管、舰用锅炉U型管和弯管进行了大量试验研究.研究发现,通过对该装置中磁致伸缩传感器的放置位置及方向进行适当调整,此装置即可在管道中激发纵向导波;该技术对管道壁厚减薄、磨损或腐蚀、裂纹、焊缝等缺陷同样具有检测能力;选择低频(20~40 kHz)激励脉冲信号有利于减少波的发散特性和提高缺陷的检测能力;导波在管道中传播衰减缓慢,适用于长距离、大范围、快速、非接触管道检测.     

地表目标复合散射的强迫激励法分析

研究了强迫激励方法在电磁散射计算中的应用 ,此方法将地表目标散射分析化为两步 :首先分析地面的散射 ,再将地面的散射作为激励作用于目标 ,从而得到地面背景下目标的电磁散射信号。应用强迫激励方法计算了地表背景下车体的时域电磁散射 ,并与试验作了对比 ,两者比较吻合     

连续旋转爆震波传播模态试验

通过保持空气流量不变、改变H2/air当量比开展了连续旋转爆震对比试验,发现随当量比的降低出现三种传播模态:在较高的当量比(0.90~1.86)下,连续旋转爆震波以同向传播模态传播;在较低的当量比(≈0.75)下,则以双波对撞模态传播;在中间工况,则以上述混合模态维持传播。分析了不同传播模态下的高频压力特征,并初步分析了传播模态的转换机制:当量比较高时,爆震强度较高,传播过程中的损失和速度亏损相对较小,爆震波以同向传播模态维持传播;当量比较低时,爆震强度较低,传播过程中的损失和速度亏损较大,此时无法维持同向传播模态,而以双波对撞模态传播,这是由于双波对撞模态中的激波对撞产生高温环境,有利于燃烧放热,其可能是连续旋转爆震的极限传播模态。     

Numerical investigation on free air blast loads generated from center-initiated cylindrical charges with varied aspect ratio in arbitrary orientation

In current guidelines, the free air blast loads (overpressure and impulse) are determined by spherical charges, although most of ordnance devices are more nearly cylindrical than spherical in geometry. This may result in a great underestimation of blast loads in the near field and lead to an unsafe design. However, there is still a lack of systematic quantitative analysis of the blast loads generated from cylindrical charges. In this study, a numerical model is developed by using the hydrocode AUTODYN to investigate the influences of aspect ratio and orientation on the free air blast loads generated from center-initiated cylindrical charges. This is done by examining the pressure contours, the peak overpressures and impulses for various aspect ratios ranged from 1 to 8 and arbitrary orientation monitored along every azimuth angle with an interval of 5°. To characterize the distribution patterns of blast loads, three regions, i.e., the axial region, the vertex region and the radial region are identified, and the propagation of blast waves in each region is analyzed in detail. The complexity of blast loads of cylindrical charges is found to result from the bridge wave and its interaction with primary waves. Several empirical formulas are presented based on curve-fitting the numerical data, including the orientation where the maximum peak overpressure emerges, the critical scaled distance beyond which the charge shape effect could be neglected and blast loads with varied aspect ratio in arbitrary orientation, all of which are useful for blast-resistant design.     

Parametric study of single confined fragment launch explosive device

In this article, parametric study of single confined fragment launch device was carried out. The configuration proposed was further studied to derive the empirical relationship for effect of fragment size, charge size, confinement thickness on fragment velocity. The simulations were carried out using ANSYS-AUTODYNE explicit solver. Fragment velocities were estimated as a function of different parametric combinations of explosive quantities, charge length to diameter ratio, fragment height to diameter ratio, confinement thickness, fragment material and fragment mass. The data was further converted to charge to metal ratio under fragment and confinement. It was observed that, increase in confinement thickness, charge quantity and decrease in fragment height increases the fragment velocity. It is also noted that, charge to metal mass ratio under fragment significantly affects the fragment velocity. At the end, an empirical relationship for fragment velocity interms of all these parameters was established. Using these relations, two velocities 1831.92 m/s and 2523.9 m/s required for NATO STANAG 4496 IM test were estimated. The design parameters for these velocities are presented. Also, the results estimated using the empirical relationship has been compared with published experimental data. Error in the predicted velocities is within the acceptable range. The empirical relationship proposed will be useful for finalization of design of the fragment launch device.     

Effect of the end cap on the fragment velocity distribution of a cylindrical cased charge

The prediction of the fragment velocity distribution of a cylindrical cased charge with end caps is one of the key issues to assess the damage efficiency of the warhead. However, limited work has been con-ducted to predict the fragment velocity distributions along the axis of cylindrical cased charges with end caps. This paper presents a study of the velocity distribution of fragments caused by the explosion of a cylindrical cased charge with end caps. The fragment velocity distribution and the end cap velocity were determined by an X-ray radiography method, and the axial fragment distribution was determined by witness plates. It was found that the velocities of fragments, especially near the edge, were increased when the end caps were added, and the position of maximum velocity is closer to the non-detonation end. The fragment velocities were increased, and the fragment projection range was decreased with the increase of the thickness of the end cap. A formula for fragment velocity distributions of a cylindrical cased charge with end caps, which is based on Huang's formula, was proposed by the theoretical analysis and data fitting and validated experimentally. The results indicate that the proposed formula is accurate in predicting the fragment velocity distribution along the axis of a cylindrical cased charge with end caps detonated at one end.