水下应用栅格翼动态展开参数预示方法

基于水下应用栅格翼动态展开过程动力学模型,根据展开特征角度定常水动力方法,拟合获得展开全程受到的流体力矩,并引入考虑相对速度影响的修正因子,形成水下应用栅格翼动态展开过程参数工程预示方法,以典型展开时序点航行体运动参数为设计输入,对栅格翼展开过程运动参数进行预示。通过与水下应用栅格翼非定常流场仿真计算数据以及水下航行体弹射试验数据对比,验证了上述预示方法的正确性及工程适用性,为水下应用栅格翼方案设计的优化及展开不同步性分析提供设计参考。     

基于遗传算法的车用散热器优化设计

选取散热器的散热量、体积和压降作为优化目标,采用线性加权法建立了散热器的多目标优化模型。在给定的散热器原始数据和性能要求条件下,对散热器芯体的外形尺寸和翅片参数进行了优化。介绍了遗传优化算法的执行步骤和流程,在此基础上开发了优化程序。结果表明,优化后散热器的散热量明显增大,散热器芯体的体积和压降也有不同程度的减小。     

Formation of explosively formed penetrator with fins and its flight characteristics

The ultimate goal of weapon system employing an explosively formed penetrator (EFP) is to defeat a target at the longest standoff. In order to do this, an EFP must be aerodynamically stable so as to strike the target at a small angle of obliquity, and the decay velocity per meter of EFP must be smaller at extended standoff. As the angle of attack increases, the penetration ability of EFP greatly reduces. The fins improve the EFP aeroballistic characteristics and decrease the flight drag of EFP as well. EFP with fins formed by three-point initiation is presented. The formation of EFP with fins is studied by LS-DYNA, and the aeroballistics is studied through experiment. The experimental results show that the decay velocity per meter of EFP with fins is much smaller than that of normal EFP, and the attitude angle steadily decreases.     

气动弹性影响下高超声速飞行器动力学建模与分析

高超声速飞行器通常采用轻质材料和细长升力体设计,导致受控刚体运动频率与结构振动频率趋于接近,给飞行器制导控制系统设计带来了巨大挑战。基于假设模态下建立了考虑变截面效应的高超声速飞行器自由梁结构动力学模型,对比了横截面梁和变截面梁模态振型和频率;考虑变截面效应后,振型变化较大,同时二、三阶模态频率均变小。给出了耦合气动弹性和飞行动力学的高超声速飞行器运动方程。在典型工况下,对比分析了刚体、常截面梁和变截面梁高超声速飞行器的平衡和动态特征,结果说明:变截面梁在平衡状态下附加攻角更大,系统在平衡点处开环不稳定性更大,同时非最小相位行为基本不变。     

拖曳系统的水翼控制运动模型及仿真

针对水下拖曳系统深度难以实现精确控制的问题,提出并建立了基于水翼控制的水下拖曳系统运动模型,其中拖缆和拖体的动力学模型分别采用了有限差分法和水下运载器的六自由度运动方程。在此基础上,使用数值计算方法,实现了水下拖曳系统三维的运动响应分析,并运用PID方法控制水翼攻角,达到了对拖体目标深度的控制。仿真结果验证了这一运动模型的正确性,为进一步实现水下拖曳系统在各种复杂的海洋环境和船舶机动影响下的定深控制研究奠定了理论基础。     

小水线面双体船横摇阻尼特性数值与试验研究

针对安装稳定鳍的小水线面双体船开展了零速静水自由横摇衰减数值与试验研究。通过不确定度分析验证数值计算方法的可靠性,进而对比船体的线性横摇阻尼和非线性横摇阻尼,并分析摩擦阻尼和稳定鳍对小水线面双体船横摇恢复力矩的影响规律。结果表明:由数值计算求得的自由横摇衰减曲线与试验结果吻合良好;在线性横摇运动假设下,线性横摇阻尼系数随着初始横倾角的增加而增大;将通过数值计算求得的非线性阻尼系数代入到非线性横摇运动方程中能准确地模拟船体的自由横摇衰减运动;摩擦阻尼和稳定鳍对小水线面双体船零速静水自由横摇时的横摇恢复力矩贡献很小。     

小水线面双体船（SWATH）耐波性特点及影响因素分析

本文应用切片理论预报了ＳＷＡＴＨ耐波性,建立了ＳＷＡＴＨ的耐波性理论预报程序。通过若干艘ＳＷＡＴＨ的耐波性计算,分析了船形及固定式鳍的尺度、纵向位置、组合方式的变化以及纵摇角速度负反馈自动控制鳍对ＳＷＡＴＨ耐波性的影响,为ＳＷＡＴＨ的船形设计及鳍的方案选择提供了耐波性方面的根据。     

Split delivery routing

This article examines a relaxed version of the generic vehicle routing problem. In this version, a delivery to a demand point can be split between any number of vehicles. In spite of this relaxation the problem remains computationally hard. Since only small instances of the vehicle routing problem are known to be solved using exact methods, the vehicle route construction for this problem version is approached using heuristic rules. The main contribution of this article to the existing body of literature on vehicle routing issues in (a) is presenting a new vehicle routing problem amenable to practical applications, and (b) demonstrating the potential for cost savings over similar “traditional” vehicle routing when implementing the model and solutions presented here. The solution scheme allowing for split deliveries is compared with a solution in which no split deliveries are allowed. The comparison is conducted on six sets of 30 problems each for problems of size 75, 115, and 150 demand points (all together 540 problems). For very small demands (up to 10% of vehicle's capacity) no significant difference in solutions is evident for both solution schemes. For the other five problem sets for which point demand exceeds 10% of vehicle's capacity, very significant cost savings are realized when allowing split deliveries. The savings are significant both in the total distance and the number of vehicles required. The vehicles' routes constructed by our procedure tend to cover cohesive geographical zones and retain some properties of optimal solutions.     

高超声速飞行器舵机摩擦的影响及其抑制方法

高超声速飞行器非线性性影响飞行姿态控制,本文在某型轴对称高超声速飞行器滚转通道数学仿真模型的基础上,仿真分析了基于静摩擦+库仑摩擦+黏性摩擦模型的舵机摩擦环节对滚转通道控制的影响,指出该摩擦环节会导致滚转通道振荡,最后提出采用非线性PID控制算法作为舵机控制算法抑制该摩擦环节。仿真结果表明舵机应用该控制算法在不显著改变舵机性能的同时能削弱舵机摩擦环节对飞行控制的影响。     

载体干扰磁场补偿方法

获得载体航行路径上各点地磁场的精确测量值是地磁匹配导航的前提,而载体上各种干扰磁场的存在会引起磁力仪输出的偏差,影响匹配的精度,因此必须对载体干扰磁场进行补偿。在分析载体干扰磁场特性的基础上,提出利用矢量测量值对地磁场总场值进行补偿的方法。该方法首先根据矢量磁力仪的测量模型得到关于载体磁场参数的非线性方程,然后采用非线性参数估计方法估计出精确的载体干扰磁场系数,最后再利用估计结果对测量值进行补偿。通过仿真对该方法的有效性进行研究,并设计了半实物实验对其实用性进行验证。结果表明采用本文提出的方法补偿后地磁场总场值的测量误差在20nT以内,而且该方法参数估计精度高,应用方便,可以有效地对导航载体干扰磁场进行补偿。     

高超声速滑翔式升力体外形设计与优化

针对高超声速飞行器外形参数多、气动布局设计复杂的问题,基于类型函数/形状函数变换技术和幂函数表达方法,采用6个控制参数设计了一种便于分析与设计的升力体构型。通过正交试验分析了各参数对升力体容积率和升阻比的影响,得到了对性能影响较大的参数,并发现几乎所有的控制参数对容积率和升阻比的影响趋势都是相反的,进而以纵向稳定性和容积为约束条件,对升阻比和容积率进行多目标优化。结果表明,基于Kriging代理模型技术的多目标优化方法计算效率高,得到的优化前缘均匀,典型优化结果的容积率和升阻比较基本外形分别提高17.31%和11.94%,并且由于代理模型构建时采用了改进的EI加点策略,优化结果的误差能达到4%以内,完全满足初步设计的要求。另外研究了边缘钝化对优化设计结果的影响,边缘钝化能显著减小升阻比,钝化半径越大升阻比越小。而且当仅考虑气动力特性时,基于尖锐前缘外形得到的优化结果能直接外推到钝化条件下。     

基于模糊干扰观测器的高超声速飞行器一体化制导控制方法

为充分利用高超声速飞行器在俯冲段的质心运动与绕质心运动之间的耦合作用和飞行过程中的不确定性，基于模糊干扰观测器提出了三维一体化制导与控制问题。首先根据飞行器的动力学方程以及飞行器-目标的视线角相对运动方程，推导出来适用于倾斜转弯控制的一体化制导控制模型。接着，针对模型中的不确定性采用模糊干扰观测器进行补偿，并使用块动态面方法设计了一种一体化制导控制律。然后，通过选取适当的李雅普诺夫函数证明了闭环系统状态的一致毕竟有界性。最后，仿真结果验证了该一体化制导控制方法的有效性和鲁棒性。     

Approximation algorithms for the capacitated traveling salesman problem with pickups and deliveries

We consider the Capacitated Traveling Salesman Problem with Pickups and Deliveries (CTSPPD). This problem is characterized by a set of n pickup points and a set of n delivery points. A single product is available at the pickup points which must be brought to the delivery points. A vehicle of limited capacity is available to perform this task. The problem is to determine the tour the vehicle should follow so that the total distance traveled is minimized, each load at a pickup point is picked up, each delivery point receives its shipment and the vehicle capacity is not violated. We present two polynomial‐time approximation algorithms for this problem and analyze their worst‐case bounds. © 1999 John Wiley & Sons, Inc. Naval Research Logistics 46: 654–670, 1999     

多轴特种车辆轮胎系统抗毁伤能力等毁线表征方法

为了探究战场威胁下多轴特种车辆轮胎系统的生存概率,对轮胎系统的抗毁伤能力进行量化表征,提出了一种基于等毁线的轮胎系统抗毁伤能力表征方法。针对轮胎毁伤状态下对整车的影响,基于车辆动力学对轮胎系统的力学特性进行量化表征,建立了轮胎系统功能毁伤的计算模型;采用毁伤理论对冲击波超压场进行弹目交会和量化分析,建立了轮胎系统物理毁伤的计算模型;根据爆心与车辆的位置关系,采用面向车辆全面域的计算特征线,建立了轮胎系统等毁线计算模型。以某型五轴特种车辆为例,进行了表征方法验证。研究结果表明:该表征方法可应用于战场威胁下多轴特种车辆轮胎系统的抗毁伤能力表征,为后续机动规避和防护能力提升奠定模型基础。     

单级入轨运载器干质量影响因素分析

提出了单级入轨运载器干质量计算方法。对给定的飞行任务,提出了基准运载器,并计算了贮箱材料、热防护系统及设计余量对运载器干质量的影响。计算结果表明,先进的材料和设计能降低运载器的干质量,并使运载器干质量对设计余量的敏感性降低     

轮毂电机驱动车辆转向控制策略

为提高轮毂电机驱动车辆转向机动灵活性以及安全稳定性,提出了一种基于直接横摆力矩控制的转向控制策略。以带有双桥转向机构的8轮轮毂电机驱动车辆为研究对象,研究其双重转向控制问题,建立基于车辆二自由度单轨模型的车辆参考模型,并以横摆角速度作为控制变量,建立基于横摆力矩PID控制器和横摆力矩分配控制器的转向分层控制模型。利用硬件在环实时仿真实验对所提出的转向控制策略的可行性和有效性进行分析验证。     

通过变维kalman滤波实现融合定位

为了能更好地跟踪、定位机动目标,提出了一种将蜂窝网定位信息与本地传感器信息相融合,利用变维Kalman滤波实现定位的方法。本地传感器信息指目标的运动速度和方向。仿真实验证明该方法具有较强的机动跟踪能力,定位精度高,且计算相对简便。     

Vehicle fleet refueling strategies to maximize operational range

The focus of this research is on self-contained missions requiring round-trip vehicle travel from a common origin. For a single vehicle the maximal distance that can be reached without refueling is defined as its operational range. Operational range is a function of a vehicle's fuel capacity and fuel consumption characteristics. In order to increase a vehicle's range beyond its operational range replenishment from a secondary fuel source is necessary. In this article, the problem of maximizing the range of any single vehicle from a fleet of n vehicles is investigated. This is done for four types of fleet configurations: (1) identical vehicles, (2) vehicles with identical fuel consumption rates but different fuel capacities, (3) vehicles which have the same fuel capacity but different fuel consumption rates, and (4) vehicles with both different fuel capacities and different consumption rates. For each of the first three configurations the optimal refueling policy that provides the maximal range is determined for a sequential refueling chain strategy. In such a strategy the last vehicle to be refueled is the next vehicle to transfer its fuel. Several mathematical programming formulations are given and their solutions determined in closed form. One of the major conclusions is that for an identical fleet the range of the farthest vehicle can be increased by at most 50% more than the operational range of a single vehicle. Moreover, this limit is reached very quickly with small values of n. The performance of the identical fleet configuration is further investigated for a refueling strategy involving a multiple-transfer refueling chain, stochastic vehicle failures, finite refueling times, and prepositioned fleets. No simple refueling ordering rules were found for the most general case (configuration 4). In addition, the case of vehicles with different fuel capacities is investigated under a budget constraint. The analysis provides several benchmarks or bounds for which more realistic structures may be compared. Some of the more complex structures left for future study are described.     

再入快速抵达轨迹优化设计方法

针对再入初始速度大、飞行时间约束苛刻的轨迹设计问题,提出一种基于遗传算法和攻角+倾侧角联合优化的再入快速抵达轨迹优化设计方法。该方法在再入初段利用较大攻角迅速减小弹道倾角和拉平弹道,在再入后段/滑翔段联合设计和优化攻角+倾侧角变化规律以显著降低终端飞行速度,同时满足终端高度、终端航向角、最大动压、最大热流等约束条件。该方法能够提升传统升力体飞行器再入快速到达能力并拓展其应用范围。仿真结果表明,在典型飞行器参数和较大初始再入速度条件下,全程飞行时间小于12 min,终端速度能够小于7Ma,横向机动距离超过800 km。     

车辆液力机械传动系统建模及动态特性仿真

建立了具有液力传动的履带车辆动力传动系统及整车的仿真模型,对车辆的加速性进行了仿真研究并与试验结果进行了比较,应用该仿真模型,分析了履带车辆换挡过程中发动机与涡轮转速、系统元件转速等的变化规律,结果表明该仿真模型能够方便的应用于车辆的性能分析与预测.