钢管约束混凝土抗侵彻性能试验

进行了12.7mm穿甲枪弹侵彻钢管约束混凝土和PVC管约束混凝土厚靶试验,建立了硬芯枪弹侵彻深度公式,研究了钢管约束混凝土的抗侵彻性能。结果表明:钢管约束混凝土靶的破坏模式与无约束混凝土靶存在显著不同,其核心混凝土侧面出现了环向裂纹;相对于无约束混凝土靶,钢管约束混凝土靶的抗侵彻能力明显提高,并具有较强的抗多发打击能力。     

基于层裂机理的弹体侵彻混凝土的终点弹道研究

基于动态球形空腔膨胀理论给出的阻力函数理论公式和开坑阶段的表面层裂机理,建立了能够综合考虑弹头形状、开坑区深度的斜侵彻深度预测模型,并进一步推导了能够适用不同弹头形状的弹体过载时程曲线计算公式。预测模型得到的侵彻深度和过载与试验结果吻合较好。研究结果可为弹体与混凝土靶的斜侵彻弹道分析和弹丸头部设计提供一定帮助。     

横向运动板对长杆弹侵彻的偏转作用

弹体的攻角直接影响其侵彻能力,而横向运动板能使弹体发生偏转改变攻角,间接影响弹体的侵彻能力。在一定条件下,推导长杆弹在单层横向运动板作用下的偏转模型,并利用有限元仿真软件ANSYS／LS-rDYNA对长杆弹侵彻横向运动板的过程进行数值模拟。通过对偏转模型及仿真结果的分析,发现两者较为相符。研究结果显示：长杆弹侵彻横向运动板时,弹体会发生偏转,偏转的角速度先增后减,最后为0rad／s,此时偏转角最大;弹体速度方向也会发生偏转,其最终偏转角与弹体轴线的偏转角接近。     

Integrated guidance and control of guided projectile with multiple constraints based on fuzzy adaptive and dynamic surface

Based on fuzzy adaptive and dynamic surface (FADS), an integrated guidance and control (IGC) approach was proposed for large caliber naval gun guided projectile, which was robust to target maneuver, canard dynamic characteristics, and multiple constraints, such as impact angle, limited measurement of line of sight (LOS) angle rate and nonlinear saturation of canard deflection. Initially, a strict feedback cascade model of IGC in longitudinal plane was established, and extended state observer (ESO) was designed to estimate LOS angle rate and uncertain disturbances with unknown boundary inside and outside of system, including aerodynamic parameters perturbation, target maneuver and model errors. Secondly, aiming at zeroing LOS angle tracking error and LOS angle rate in finite time, a nonsingular terminal sliding mode (NTSM) was designed with adaptive exponential reaching law. Furthermore, combining with dynamic surface, which prevented the complex differential of virtual control laws, the fuzzy adaptive systems were designed to approximate observation errors of uncertain disturbances and to reduce chatter of control law. Finally, the adaptive Nussbaum gain function was introduced to compensate nonlinear saturation of canard deflection. The LOS angle tracking error and LOS angle rate were convergent in finite time and whole system states were uniform ultimately bounded, rigorously proven by Lyapunov stability theory. Hardware-in-the-loop simulation (HILS) and digital simulation experiments both showed FADS provided guided projectile with good guidance performance while striking targets with different maneuvering forms.     

基于层裂机理的弹体侵彻混凝土的工程模型

以斜侵彻过程中的终点弹道为研究对象,基于动态球形空腔膨胀理论给出的阻力函数理论公式和开坑阶段的表面层裂机理,建立了能够综合考虑弹头形状、开坑区深度的斜侵彻深度预测模型,并进一步推导了能够适用不同弹头形状的弹体过载时程曲线计算公式。预测模型得到的侵彻深度和过载与试验结果吻合较好。研究结果可为弹体与混凝土靶的斜侵彻弹道分析和弹丸头部设计提供一定帮助。     

某型火箭弹对巡航导弹毁伤概率仿真分析

通过对巡航导弹目标特性分析,论述了目标易损性和毁伤机理(包括破片战斗部对目标的击穿概率模型)。利用破片初速及存速计算模型,分析了战斗部爆破后破片速度衰减规律,并做了模拟仿真,为火箭弹战斗部设计及毁伤效能评估提供了理论依据。最后根据射弹散布规律及毁伤原理建立了毁伤模型,并以某型火箭弹为例,对毁伤概率模型进行了仿真分析。仿真结果表明:该方法为火箭弹战斗部设计和提高对巡航导弹毁伤概率提供了参考。     

加筋板架抗动能穿甲的等效防护厚度研究

为研究舰船舷侧结构抗穿甲性能,采用有限元分析了两种典型工况下板架的穿甲破坏模式、弹体的剩余速度和板架的变形吸能规律,提出了基于剪切冲塞模式的剩余速度理论计算模型,比较了不同等效计算方法得到的结果,并将理论计算结果分别与相关文献的实验结果和本文的有限元计算结果进行了比较,两者之间均吻合较好。结果表明,加强筋对板架的抗穿甲性能影响较大,而板架的实际等效厚度是决定其抗穿甲性能的主要因素;不同的等效计算方法与模型相对尺寸、弹体冲击速度以及命中位置有关,对于弹体直径相对较大且初始冲击速度较高时,不同的等效计算方法得到的结果基本一致。     

Damage modeling of ballistic penetration and impact behavior of concrete panel under low and high velocities

This work presents a numerical simulation of ballistic penetration and high velocity impact behavior of plain and reinforced concrete panels. This paper is divided into two parts. The first part consists of numerical modeling of reinforced concrete panel penetrated with a spherical projectile using concrete damage plasticity (CDP) model, while the second part focuses on the comparison of CDP model and Johnson-Holmquist-2 (JH-2) damage model and their ability to describe the behavior of concrete panel under impact loads. The first and second concrete panels have dimensions of 1500 mm × 1500 mm × 150 mm and 675 mm × 675 mm × 200 mm, respectively, and are meshed using 8-node hexahedron solid elements. The impact object used in the first part is a spherical projectile of 150 mm diameter, while in the second part steel projectile of a length of 152 mm is modeled as rigid element. Failure and scabbing characteristics are studied in the first part. In the second part, the com-parison results are presented as damage contours, kinetic energy of projectile and internal energy of the concrete. The results revealed a severe fracture of the panel and high kinetic energy of the projectile using CDP model comparing to the JH-2 model. In addition, the internal energy of concrete using CDP model was found to be less comparing to the JH-2 model.     

Interface defeat studies of long-rod projectile impacting on ceramic targets

The interface defeat phenomenon always occurs when a long-rod projectile impacting on the ceramic target with certain velocity, i.e., the projectile is forced to flow radially on the surface of ceramic plates for a period of time without significant penetration. Interface defeat has a direct effect upon the ballistic performance of the armor piercing projectile, which is studied numerically and theoretically at present. Firstly, by modeling the projectiles and ceramic targets with the SPH (Smoothed Particle Hydrodynamics) particles and Lagrange finite elements, the systematic numerical simulations on interface defeat are performed with the commercial finite element program AUTODYN. Three different responses, i.e., complete interface defeat, dwell and direct penetration, are reproduced in different types of ceramic targets (bare, buffered, radially confined and oblique). Furthermore, by adopting the validated numerical algorithms, constitutive models and the corresponding material parameters, the influences of projectile (material, diameter, nose shape), constitutive models of ceramic (JH-1 and JH-2 models), buffer and cover plate (thickness, constraints, material), as well as the prestress acted on the target (radial and hydrostatic) on the interface defeat (transition velocity and dwell time) are systematically investigated. Finally, based on the energy conservation approach and taking the strain rate effect of ceramic material into account, a modified model for predicting the upper limit of transition velocity is proposed and validated. The present work and derived conclusions can provide helpful reference for the design and optimization of both the long-rod projectile and ceramic armor.     

A three-stage model for the perforation of finite metallic plates by long rods at high velocities

A three-stage theoretical model is presented herein to predict the perforation of a thick metallic plate struck normally by a long rod at high velocities. The model is suggested on the basis of the assumption that the perforation of a thick metallic plate by a long rod can be divided into three stages: (1) initial penetration; (2) plug formation and (3) plug slipping and separation. Various analytical equations are derived which can be employed to predict the ballistic limit, residual velocity and residual length of the long rod. It is demonstrated that the present model predictions are in good agreement with available experimental results for the perforation of finite steel targets struck normally by steel as well as tungsten alloy long rods at high velocities. It is also demonstrated that the dynamic maximum shear stress of a plate material has strong effect on plug formation and plug thickness which, in turn, exerts considerable influence on the residual velocities and lengths of a long rod at impact velocities just above the ballistic limit.     

一种变质心高速旋转炮弹鲁棒姿态控制律

针对采用变质心技术的高速旋转炮弹的姿态控制问题,提出一种基于扩张状态观测器的动态面控制方法。根据由弹体和单滑块组成的多体系统的特点,建立了系统的姿态动力学模型,并对其进行了合理的简化。将系统的滚转通道引起的强耦合、建模误差及外部扰动等视为未知不确定干扰,并且考虑由于炮弹尺寸限制而引起的多体系统控制输入(滑块位移)的有限性,设计了扩张状态观测器和辅助系统,分别对系统的干扰进行观测以及处理控制输入的有限性,综合动态面控制技术设计了姿态控制律,最后基于李雅普诺夫稳定性原理证明了控制器的稳定性。仿真结果表明,该控制器能够在克服干扰的前提下快速稳定地跟踪指令信号,具有良好的控制精度和鲁棒性。     

利用数字狭缝摄像技术估计弹丸速度和攻角

针对目前靶场中胶片式狭缝摄影技术的缺点和数字化改进的难点,提出了基于线阵摄像机的数字狭缝摄像技术来估计弹丸速度和攻角.该方法首先利用单台标定的摄像机配合双像器获取弹丸的立体影像,提取有限个控制点,计算弹丸速度、姿态等的初始估计值.然后利用弹丸的模拟成像与实际成像的轮廓匹配构建最优化模型,对初始估计值进行优化,最后获得弹丸的速度和攻角.通过试验验证了该方法估计弹丸速度和攻角的精确性.     

长杆射弹对钢纤维混凝土靶开坑特性的实验研究

为考察射弹对钢纤维混凝土靶的侵彻特性,采用57mm轻气炮,进行了小尺寸模拟射弹对钢纤维混凝土靶(钢纤维的体积分数为2%)的侵彻实验。实验中观察了钢纤维混凝土靶的开坑形状,测量了射弹的击靶速度,并且采用注沙法测出靶体的开坑体积,计算出射弹对靶体的侵彻体积,得到了长杆射弹的动能与侵彻体积的关系。引入射弹单位面积的冲击动能和靶体单位侵彻体积的冲击动能,结合钢纤维混凝土靶的实验数据,考察了两者之间的关系。     

某型火箭炮弹对面积目标的毁伤仿真

某型火箭炮是新型的主战装备,对其战术技术性能的研究具有重要意义。采用仿真的方法对该型武器系统对目标的毁伤过程进行研究,可以大大节约实弹射击所需经费,并且可以动态地观察毁伤过程的细节。根据某型火箭炮弹抛撒子弹模型及子弹毁伤目标性能指标,采用理论分析和计算机模拟手段,对该型火箭炮弹对面积目标的毁伤过程进行了仿真,并得出了毁伤效率随子弹枚数和CEP的变化规律。研究成果对该型武器系统的作战运用具有借鉴意义。     

伺服机构故障下基于线性规划的运载火箭姿控系统重构控制

发动机伺服机构故障给新一代运载火箭姿控系统的可靠性和安全性带来挑战,亟须开展重构控制策略研究。针对这一问题,提出一种基于线性规划的摆角重构控制分配方法。将伺服机构故障下的摆角分配问题转化为1范数单目标有约束优化问题,进而转化为标准的线性规划模型,采用单纯形法进行求解。仿真结果表明,所提出的线性规划法能够实现伺服机构故障下姿控系统的完全重构,各摆角均未达到饱和值,表明了方法的有效性。     

双高速摄像机交汇的高旋弹丸位姿估计算法及误差分析

为了测量高旋弹丸在炮口处的各种信息,基于双高速摄像机交汇的测量方法,提出了一种新的弹丸位姿估计方法.对总攻角函数进行了误差建模与分析,结果表明两台高速摄像机的光轴应相互垂直,且应选择光轴远离攻角平面的高速摄像机所对应的测量函数计算总攻角,此时测量误差最小.以靶场实验的方式对攻角函数的误差分析结论和位姿估计算法进行验证....     

Study on performance degradation and failure analysis of machine gun barrel

An increase in the use of the gun barrel will cause wear of the inner wall, which reduces the muzzle velocity and the spin rate of the projectile. The off-bore flight attitude and trajectory of the projectile also change, affecting the shooting power and the accuracy. Exterior ballistic data of a high-speed spinning projectile are required to study the performance change. Therefore, based on the barrel's accelerated life test, the whole process of projectile shooting is reproduced using numerical simulation technology, and key information on the ballistic performance change at each shooting stage are acquired. Studies have shown that in the later stages of barrel shooting, the accuracy of shooting has not decreased significantly. However, it is found that the angle of attack of the projectile increases as the wear of the barrel increases. The maximum angle of attack reaches 0.106 rad when the number of shots reaches 4300. Meanwhile, elliptical bullet hole has appeared on the target at this shooting stage. Through combining external ballistic theory with simulation results, the primary reason of this phenomenon is found to be a significant decrease in the muzzle spin rate of the projectile. At the end of the barrel life, the projectile muzzle spin rate is 57.5% lower than that of a barrel without wear.     

A novel method for determination of lethal radius for high-explosive artillery projectiles

A new model has been defined that enables the estimation of the lethal radius (radius of efficiency) of HE (High Explosive) artillery projectiles against human targets. The model is made of several modules: CAD (Computer Aided Design) modeling, fragment mass distribution estimation, fragment initial velocity prediction, fragment trajectory calculation, effective fragment density estimation, and high explosive projectile lethal radius estimation. The results were compared with the experimental results obtained based on tests in the arena used in our country, and the agreement of the results was good. This model can be used in any terminal-ballistics scenario for high explosive projectiles since it is general, para-metric, fast and relatively easy to implement.     

Study of high-speed interaction processes between fluoropolymer projectiles and aluminum-based targets

The experimental results and numerical modeling of penetration process of fluoropolymer projectiles in aluminum-based targets are presented. Analysis of mathematical models for interaction of elastoplastic projectile and target without taking additional energy released during interaction of fluoropolymer and aluminum into consideration is carried out. Energy fraction which is spent effectively on the increase in cavity volume is determined. The experimental and calculated results of penetration by combined and inert projectiles are compared.     

Analysis on the resistive force in penetration of a rigid projectile

According to the dimensionless formulae of DOP (depth of penetration) of a rigid projectile into different targets, the resistive force which a target exerts on the projectile during the penetration of rigid projectile is theoretically analyzed. In particular, the threshold V_c of impact velocity applicable for the assumption of constant resistive force is formulated through impulse analysis. The various values of V_c corresponding to different pairs of projectile-target are calculated, and the consistency of the relative test data and numerical results is observed.