复合材料帽形加筋梁强度及刚度实用计算与试验

利用变形协调方程,推导了复合材料帽形加筋梁的等效弯曲刚度公式,建立了复合材料帽形加筋梁的应力、挠度计算公式.计算了均布荷载作用下,不同边界条件下复合材料帽形加筋梁的应力和挠度,并进行了帽形加筋梁的三点弯曲强度试验.对比分析了数值计算结果和试验结果,结果表明:理论计算结果和试验结果吻合较好,说明该方法以及推导的计算公式是可靠的,易于在复合材料船体初步设计阶段中使用.     

ORGANISING THE BLUES

While all governments in the region acknowledge the importance of the work of police officers, they seldom take a close look at their working conditions and the nature of police labour. While the situations in Namibia, Zimbabwe, Zambia, Lesotho and Swaziland are different there are commonalities: police management has not changed significantly and neither has police legislation. Key concerns of the officers in the region centre on service conditions and wages. Communicating these concerns to the state is made difficult by the less than democratic approach taken by governments professing to favour democratization. A more democratic workplace for the police is of benefit to the broader community and is a crucial point to bear in mind when attempting to develop community-oriented professional policing.     

基于步进加速寿命试验的制导弹药储存寿命评估

介绍步进应力加速寿命试验原理,通过对制导弹药自动导引头贮存状态和失效机理的分析,确定了加速寿命试验应力和应力水平．假设产品寿命服从威布尔分布,应用极大似然估计和Bayes的方法处理数据,建立制导弹药可靠储存寿命预测模型,并计算得到自动导引头在正常应力水平下的可靠储存寿命．     

位移不连续法在裂纹扩展仿真中的应用

探讨了在应用位移不连续法仿真裂纹扩展时对加载方式、裂纹扩展长度及应力强度因子计算等问题的处理方法,并据此编制了仿真程序,分析了裂纹在单向压载作用下的扩展趋势和应力变化,具有一定的工程应用价值。     

大口径火炮身管热弯曲计算与试验

建立火炮在阳光照射下身管上下表面温度场、热弯曲及炮口角的计算模型。以某大口径长身管火炮为实例,计算该炮的炮口弯曲量与炮口角,进行自然阳光照射与环境模拟条件下的热弯曲试验,验证计算模型与计算结果的正确性与可信性;提出通过测量身管上下表面温度快速求取火炮身管不同环境温度及温差下的弯曲量与炮口角的工程应用方法。     

燃烧室压力对潜入式喷管喉衬热应力的影响

为了研究燃烧室压力对固体火箭发动机潜入式喷管热应力影响规律的问题,采用商业流体软件,基于压力求解器,求解了喷管纯气相的流场,确定了燃气温度、压力、壁面对流换热系数;采用有限元软件,依据流场计算的非均布壁面压力与非均布对流换热,求解了燃烧室压力为6 MPa下的潜入式喷管热结构问题;通过地面点火试验验证了仿真模型与数值方法的有效性与准确性;采用相同计算模型与数值方法,求解了在燃烧室压力为9 MPa、12 MPa下的喷管热结构问题,揭示了燃烧室压力对喉衬热应力的影响规律。结果表明:整个工作过程,喉衬环向应力最大值为103.9 MPa,位于内表面,且随时间增大,先增大后减小;喉衬环向拉应力也随时间先增大后减小;随压力增大,对流换热系数增大,喉衬温度升高,喉衬环向拉应力增大,喉衬环向压应力减小。     

Influences of different crossing types on dynamic response of underground cavern subjected to ground shock

An intersecting cavern is a common structural form used in underground engineering, and its safety and stability performance directly control the service performance of the whole project. The dynamic re-sponses of the three kinds of crossing type (+-shaped, T-shaped, L-shaped) caverns subjected to ground shock were studied by numerical simulation. The velocity plus force mode boundary setting method was proposed in the coupled static and dynamic analysis of a deep underground cavern. The results show that, among the three types of crossing caverns, the+-shaped cavern is the most significantly affected by the dynamic action, followed by T-shaped, and then L-shaped caverns. The vault settlement, straight wall deformation, vault peak particle velocity, effective plastic strain of surrounding rock, and maximum principal stress and strain at the bottom of the lining of the straight wall increase with the increase of cavern span. The vault settlement, straight wall deformation, effective plastic strain of surrounding rock, and the maximum principal stress and strain at the bottom of lining to the straight wall decrease with the increase of lateral pressure coefficient, and the peak particle velocity at the vault increases. The variation is small compared with the change of cavern span. The influence range of the underground cavern intersection is two cavern diameters from the intersection centre. The bottom of the straight wall at the intersection is the weak part. It is suggested to thicken the support locally to improve the stability of the cavern.     

Effect of friction stir processing on mechanical properties and heat transfer of TIG welded joint of AA6061 and AA7075

Tungsten inert gas (TIG) welding is the most commonly used joining process for aluminum alloy for AA6061 and AA7075 which are highly demanded in the aerospace engineering and the automobile sector, but there are some defects occur during TIG welding like micro-crack, coarse grain structure, and porosity. To improve these defects, the TIG welded joint is processed using friction stir processing (FSP). This paper presents the effect of friction stir processing on TIG welding with filler ER4043 and ER 5356 for dissimilar aluminum alloy AA6061 and AA7075. The mechanical characterization, finite element formulation and mathematical equations of heat transfer of TIG + FSP welded joints are investigated using ANSYS Fluent software by adjusting process parameters of FSP. The results show that the maximum compressive residual stress 73 MPa was obtained at the fusion zone (FZ) of the TIG weldment with filler ER4043, whereas minimum compressive residual stress 37 MPa was obtained at stir zone (SZ) of the TIG+FSP with filler 5356. The maximum heat flux 5.33 × 106 W/m2 and temperature 515 ℃ have observed at tool rotation 1600 rpm with a feed rate of 63 mm/min. These results give a satisfactory measure of confidence in the fidelity of the simulation     

自润滑弹带挤进过程中渗出油量的对比计算

从弹带的作用及特性出发, 通过数值计算和统计计算 2种方法计算了自润滑弹带挤进过程中的渗出油量,初步得出了渗出油量和行程之间的关系。这一问题的解决为自润滑弹带材料的选择提供了理论依据。通过对 2种算法的比较可知, 数值计算误差更小一些, 而统计计算对数学条件要求不太苛刻。     

大功率消磁线圈受力分析与计算

大功率消磁线圈在运行中会受到较强电磁力的作用,客观地分析和计算电磁力的大小及分布情况,是设计和建造大型消磁站的一项基础性的工作.文中从电磁场基本原理出发,应用张量理论分析、计算了大功率消磁线圈的受力情况,对于设计和建造大型消磁站具有参考作用.