破片模拟弹侵彻钢板的有限元分析

根据破片模拟弹侵彻钢板的实验研究,采用MSC.Dytran对破片模拟弹侵彻钢板的侵彻过程、侵彻特性、钢板的破坏模式以及弹体的侵彻速度、靶板的侵彻阻力进行了有限元分析,并将分析结果与实验结果进行了比较.分析结果表明,破片模拟弹冲击钢装甲的侵彻过程可大致分为初始接触、弹体侵入、剪切冲塞和穿甲破坏4个阶段.有限元分析的破片模拟弹侵彻特性及靶板破坏模式与实验观测结果有较好的一致性,在靶板破口的正面,与弹体平面凸缘两端接触的部分,变形以剪切为主,而与切削面接触的部分,以挤压变形为主;靶板破口背面为剪切冲塞破坏;有限元模拟的弹体剩余速度与实验结果吻合较好,弹体侵彻过程中弹靶作用界面的速度和侵彻速度近似呈线性变化.有限元分析结果还表明,采用适当的模型,有限元法能较好地模拟破片模拟弹侵彻钢板的侵彻过程、侵彻特性以及钢板的破坏模式.     

A case study in bio-inspired engineering design: defense applications of exoskeletal sensors

As part of a bio-inspired design process, the authors examine exoskeletal sensors found in insects and their potential application to armor and hardened buildings. In this way, the outer hardening of a structure or vehicle would not limit the ability of occupants to arrive at an actionable picture of the outer environment. To this end, various sensor modalities employed by insects are compared and contrasted with their current human-engineered equivalents. In several sensing modalities, biosensors perform better, are smaller, and more energy efficient than human-engineered equivalents. They note that biological designs tend to employ non-linear response to signal amplitude and respond with heightened sensitivity over a greater dynamic range of signals than human-engineered sensors. The insect biological sensors have structural and mechanical innovations that preserve the protective capacity of the exoskeleton.     

The Armoury Gauging System and Interchangeable Manufacture

Abstract

Scientifically analysing important artefacts from the site of historic battles is vital if the best information is to be retrieved from the field. A detailed knowledge of the specific equipment that was available to the combatants from a known battle is also required at a high level so that artefacts and fragments resulting from an historic battlefield archaeological survey can be recognised when found. Access to specialists from all walks of life is required throughout each battlefield-related project, from the fieldwork stages to the dissemination of information. The following paper discusses the importance of working alongside museums and specialists and gives examples of how the Towton Battlefield Archaeology Project has successfully worked with the staff at the Royal Armouries Leeds.     

新型夜瞄复合荧光材料在步兵轻武器中的应用研究

采用自制的复合荧光粉体和化学载体成分,研制出一种步兵轻武器新型夜瞄复合荧光材料.试验研究和实际使用结果表明,研制的新材料发光时间长、亮度高,具有良好的耐温、耐腐蚀性能,不受轻武器的日常使用和维护影响,可满足步兵轻武器夜间瞄准需求.     

钢丝增强复合条带抗弹性能数值分析

为研究钢丝增强聚合物基复合条带的抗弹性能,基于冲击动力学理论分析其抗弹机理,再借助ANSYS/LS-DYNA软件和LS-PrePost前后处理器模拟有无增强钢丝2种工况下,条带对7.62 mm弹体的冲击响应。分析表明：条带的弹性模量、剪切模量和面密度会影响其能量吸收性能,能量吸收量随三者的增大而增大;由于聚合物基体的正交各向异性,应力云图显示出扁平椭圆状是合理的;在聚合物基复合条带中嵌入增强钢丝对条带整体的抗弹性能有积极的影响,但嵌入过量的钢丝会导致重量和成本的增加,因此需要对合理的钢丝配比率作进一步研究。研究结果可为钢丝增强聚合物基复合条带在野战防护结构中的应用提供参考。     

Damage visualization and deformation measurement in glass laminates during projectile penetration

Transparent armor consists of glass-polymer laminates in most cases. The formation and propagation of damage in the different glass layers has a strong influence on the ballistic resistance of such laminates. In order to clarify the course of events during projectile penetration, an experimental technique was developed, which allows visualizing the onset and propagation of damage in each single layer of the laminate. A telecentric objective lens was used together with a microsecond video camera that allows recording 100 frames at a maximum rate of 1 MHz in a backlit photography set-up. With this technique, the damage evolution could be visualized in glass laminates consisting of four glass layers with lateral dimensions 500 mm × 500 mm. Damage evolution was recorded during penetration of 7.62 mm AP projectiles with tungsten carbide core and a total mass of 11.1 g in the impact velocity range from 800 to 880 m/s. In order to measure the deformation of single glass plates within the laminates, a piece of reflecting tape was attached to the corresponding glass plate, and photonic Doppler velocimetry (PDV) was applied. With the photonic Doppler velocimeter, an infrared laser is used to illuminate an object to be measured and the Doppler-shifted light is superimposed to a reference light beam at the detector. The simultaneous visualization and PDV measurement of the glass deformation allow determining the deformation at the time of the onset of fracture. The analysis of the experimental data was supported by numerical simulations, using the AUTODYN commercial hydro-code.     

纤维缠绕复合材料夹芯圆柱体高应变率压缩吸能机理

为研究纤维缠绕复合材料夹芯圆柱体吸能元件在高应变率冲击压缩载荷作用下的变形损伤模式和能量吸收机理,采用ABAQUS商用有限元软件和分离式Hopkinson压杆装置开展数值模拟分析和试验验证研究。对比分析宏观力学响应规律和微观损伤破坏机理,可知吸能结构元件在高应变率压缩载荷下的力学响应具有典型的弹塑性特征,内部芯材主要产生压缩塑性损伤,而表层复合材料沿环向产生拉伸断裂破坏。研究表明,该吸能元件冲击压缩吸能特性优异,可满足水下结构平台的冲击防护和浮力储备要求。     

Fabrication of AA7005/TiB2-B4C surface composite by friction stir processing: Evaluation of ballistic behaviour

The present work aims to enhance the ballistic resistance of AA7005 alloy by incorporating the TiB₂ and B₄C ceramic reinforcement particles. Surface composites with different weight fractions of TiB₂ and B₄C particles were processed by friction stir processing. Micro-hardness and depth of penetration tests were carried out to evaluate the ballistic properties of the surface composites. The surface hardness of the composite was found to be nearly 70 HV higher than base alloy. The depth of penetration of the steel projectile was 20–26 mm in the composites as compared to 37 mm in the base alloy. Ballistic mass efficiency factor of the surface composite was found to be 1.6 times higher than base alloy. This is mainly attributed to the dispersion strengthening from the reinforcement particles.     

碳纤维/双马来酰亚胺复合材料修复性能

为了得到碳纤维/双马来酰亚胺复合材料最佳修复效果,采用碳纤维/环氧复合材料和环氧胶膜作为修复材料,对带Φ15 mm和Φ5 mm预制孔碳纤维/双马来酰亚胺复合材料进行单面贴补、双面贴补和单面阶梯挖补修复。研究了补片长度、厚度和铺层顺序对修复效果的影响,并结合修复试样的拉伸断裂模式,优化了修复参数。结果表明:补片边缘母板中存在的应力集中和厚度方向拉伸应力是导致母板断裂的关键原因;双面贴补修复试样拉伸强度能恢复到完好试样的90%以上,单面贴补和阶梯挖补修复试样拉伸强度能恢复到完好试样的80%以上。     

碳纤维增强聚合物基复合材料频率选择表面的电磁传输特性

为了避免采用金属频率选择表面制备的天线罩中存在的热残余应力和弱黏接界面等问题,采用与聚合物基复合材料罩壁结构相容性好的碳纤维增强聚合物基复合材料制备频率选择表面,利用自由空间法对试样的电磁传输性能进行测试,并采用数值分析模型对碳纤维复合材料频率选择表面的电磁传输机制和电磁传输影响因子进行分析。结果表明:碳纤维复合材料频率选择表面具有频率选择功能,但谐振频率处的电磁传输损耗较大;通过改变复合材料频率选择表面的单元缝隙率、厚度、电导率以及介电常数可以实现对其电磁传输性能的调节。