Analysis on damage characteristics and detonation performance of solid rocket engine charge subjected to jet

To further explore the damage characteristics and impact response of the shaped charge to the solid rocket engine (SRE) in storage or transportation, protective armor was designed and the shelled charges model (SCM)/SRE with protective armor impacting by shaped charge tests were conducted. Air overpressures at 5 locations and axial acceleration caused by the explosion were measured, and the experimental results were compared with two air overpressure curves of propellant detonation obtained by related scholars. Afterwards, the finite element software AUTODYN was used to simulate the SCM impacted process and SRE detonation results. The penetration process and the formation cause of damage were analyzed. The detonation performance of TNT, reference propellant, and the propellant used in this experiment was compared. The axial acceleration caused by the explosion was also analyzed. By comprehensive comparison, the energy released by the detonation of this propellant is larger, and the HMX or Al particles contained in this propellant are more than the reference propellant, with a TNT equivalent of 1.168–1.196. Finally, advanced protection armor suggestions were proposed based on the theory of woven fabric rubber composite armor (WFRCA).     

Experimental and numerical investigation of zirconium jet performance with different liner shapes design

This paper studies the shaped charge jet performance in terms of different liner shapes including conical,bell,hemispherical and bi-conical liners.The critical angles and the relevant flow velocities for the zir-conium liner material were calculated analytically and numerically using Autodyn hydro-code.The relationship between the critical collapse angle and the flow velocity was determined for the conditions of jet formation and coherency.Penetration tests according to the standard testing procedures of API-RP34 (Section-Ⅱ) were performed to validate the numerical predictions of the jet performance of the studied liners.It was found that the four shaped charge liners all produced coherent jets with different performances.The penetration depth of the shaped charges with the bell and the bi-conical liner shapes increased by 10.3％ and 22％,respectively,while the crater diameter of shaped charge with hemispherical liner increased by 85％ representing the formation of an explosively-formed-projectile (EFP),when they are compared with the corresponding jet characteristics of a conical liner shaped charge.     

基于随机拟合的悬浮式深弹弹阵特征建模＊

通过分析悬浮式深弹发射后在空中的弹道特性,建立了深弹弹着点坐标的计算模型。采取蒙特卡洛方法,分别对舰艇六自由度状态下,单管和六联装火箭深弹的弹着点坐标进行了仿真计算,对弹着点的分布规律进行了研究,并得出弹着点的联合密度函数。结果表明,在发射参数存在正态扰动时,弹着点散布区域均呈椭圆形分布,弹着点坐标均仍服从正态分布。     

聚能射流形成过程的理论建模与分析

分析了聚能射流的形成过程,并对其中的各阶段进行了详细建模。在模型中考虑了炸药爆轰、金属的驱动、药型罩压垮以及射流和杵体的形成过程。采用该模型对某一聚能装药结构进行了计算,计算结果表明:药型罩顶部和底部微元的压垮速度较小,在射流头部形成反向速度梯度,与试验数据吻合较好。该模型对于多级侵彻战斗部的工程设计与侵彻参数的计算具有一定的参考价值。     

基于旋转点电荷模型的舰船腐蚀电场

为了找出轴频电场无法彻底消除及实际测量中静电场产生波动曲线问题的原因,基于旋转点电荷的建模方法对舰船腐蚀电场进行研究。利用汉克尔变换对点电荷在三层介质中产生的电场进行近似求解,得出一定转速下感应电场随时间、螺旋桨半径及水面距离变化的规律曲线图,并通过实验验证了理论结果的正确性。结果表明:螺旋桨旋转产生的感应电场是构成舰船腐蚀电场的一部分,一定转速下的感应电场频率与螺旋桨转动频率一致,并会随着螺旋桨半径及与水面距离的增加而减小。     

航空自导深弹攻潜命中概率分析

以航空自导深弹为研究对象,在分析反潜直升机攻潜过程的基础上,依据某型航空自导深弹的有关技术参数,首先建立了反潜直升机使用航空自导深弹攻潜模型,然后详尽分析了航空自导深弹攻潜作战中的各种源误差,采用解析法计算了反潜直升机在不同条件下投放航空自导深弹攻击潜艇时的单发命中概率,得出了反潜直升机空投航空自导深弹攻潜的使用方法.这对于部队使用航空自导深弹反潜有较高的参考价值.     

镜像法求解导体球外点电荷电场的代数解

用代数法求解了导体球外点电荷在空间产生的静电场。得到了能反映导体球中自由电荷性质的新解该结果既符合唯一性定理,又有明确的物理含义。     

土壤源-湖水源热泵系统及工程应用实例

由于土壤源、湖水源热泵的应用受到地理条件、初投资等因素的制约,某些地区更适宜采用土壤源-湖水源的混合式热泵系统。以某工程应用为例,分别从性能系数、初投资及运行费用3个方面分析证明了采用混合式热泵系统的可行性。结果表明,混合式热泵系统的初投资虽然较大,但通过节约运行费用,在较短年限内可收回增加的成本,并且可以减少废水废气的排放。因此,在合适的地区可以推广使用土壤源-湖水源的混合式热泵系统。     

Effect of wave shaper on reactive materials jet formation and its penetration performance

Wave shaper effect on formation behavior and penetration performance of reactive liner shaped charge (RLSC) are investigated by experiments and simulations. The reactive materials liner with a density of 2.3 g/cm³ is fabricated by cold pressing at a pressure of 300 MPa and sintering at a temperature of 380 °C. Experiments of the RLSC with and without wave shaper against steel plates are carried out at standoffs of 0.5, 1.0, and 1.5 CD (charge diameter), respectively. The experimental results show that the penetration depths and structural damage effects of steel plates decrease with increasing the standoff, while the penetration depths and the damage effects of RLSC without wave shaper are much greater than that with wave shaper at the same standoff. To understand the unusual experimental results, numerical simulations based on AUTODYN-2D code are conducted to discuss the wave shaper effect, including the propagation behavior of detonation wave, the velocity and temperature distribution of reactive jet, and penetration depth of reactive jet. The simulations indicate that, compared with RLSC without wave shaper, there is a higher temperature produced inside reactive jet with wave shaper. This unusual temperature rise effects are likely to be an important mechanism to cause the initiation delay time of reactive jet to decline, which results in significantly decreasing its penetration performance.     

坦克铅酸蓄电池快速充电模糊控制研究

对于坦克用铅酸蓄电池快速充电问题,初步研究了采用模糊控制器控制充电过程,分析了其模糊控制器的组成,并讨论了模糊控制在铅酸蓄电池快速充电中存在的问题。