An interface shear damage model of chromium coating/steel substrate under thermal erosion load

The Cr-plated coating inside a gun barrel can effectively improve the barrel's erosion resistance and thus increase the service life.However,due to the cyclic thermal load caused by high-temperature gun-powder,micro-element damage tends to occur within the Cr coating/steel substrate interface,leading to a gradual deterioration in macro-mechanical properties for the material in the related region.In order to mimic this cyclic thermal load and,thereby,study the thermal erosion behavior of the Cr coating on the barrel's inner wall,a laser emitter is utilized in the current study.With the help of in-situ tensile test and finite element simulation results,a shear stress distribution law of the Cr coating/steel substrate and a change law of the interface ultimate shear strength are identified.Studies have shown that the Cr coating/steel substrate interface's ultimate shear strength has a significant weakening effect due to increasing temperature.In this study,the interfacial ultimate shear strength decreases from 2.57 GPa(no erosion)to 1.02 GPa(laser power is 160 W).The data from this experiment is employed to establish a Cr coating/steel substrate interface shear damage model.And this model is used to predict the flaking process of Cr coating by finite element method.The simulation results show that the increase of coating crack spacing and coating thickness will increase the service life of gun barrel.     

Q345低合金结构钢的高温强度试验研究

采用恒温加载试验方法对钢结构建筑常用的Q345低合金结构钢的高温强度进行试验研究,采用切线交点法确定钢材有效屈服强度,并与其它方法强度取值进行对比,给出钢材高温强度回归公式,为钢结构建筑的抗火分析提供依据。     

爆炸复合接头剪切强度测试方法研究

参照正交各向异性层压复合板层间剪切强度的测试方法,提出了用于测试爆炸复合接头复合界面剪切强度的3种方法;并建立三维有限元模型,分别对3种测试方法进行模拟;最后分别对3种方法进行了测试试验.结果表明,3种试验方法均能有效测试爆炸复合接头的剪切强度,其中对称试件双切口拉伸法最适合实际应用.     

Experimental and numerical investigation of zirconium jet performance with different liner shapes design

This paper studies the shaped charge jet performance in terms of different liner shapes including conical,bell,hemispherical and bi-conical liners.The critical angles and the relevant flow velocities for the zir-conium liner material were calculated analytically and numerically using Autodyn hydro-code.The relationship between the critical collapse angle and the flow velocity was determined for the conditions of jet formation and coherency.Penetration tests according to the standard testing procedures of API-RP34 (Section-Ⅱ) were performed to validate the numerical predictions of the jet performance of the studied liners.It was found that the four shaped charge liners all produced coherent jets with different performances.The penetration depth of the shaped charges with the bell and the bi-conical liner shapes increased by 10.3％ and 22％,respectively,while the crater diameter of shaped charge with hemispherical liner increased by 85％ representing the formation of an explosively-formed-projectile (EFP),when they are compared with the corresponding jet characteristics of a conical liner shaped charge.     

边坡稳定性理论及其局限性

边坡分析理论经过近几十年的发展,基本形成了完善的体系。较为典型的有 极限平衡法,极限分析法,有限元法等。对各种分析方法做了简要的回顾与评述。基于极限 平衡原理发展的各种分析方法,大多需要做许多假设,同时对岩质边坡又不能很好地考虑其 断层节理特征。有限元强度折减法,是近年来发展起来的一种分析方法,与极限平衡法相比 不需要任何假设,可以求得任意形状边坡的临界滑移面及其对应的安全系数,同时可以反映 边坡失稳及塑性区的发展过程,为岩土体边坡分析开辟了新的途径。     

材料电导率对混响室场性能影响的仿真研究

混响室作为一种经济有效的新型电磁兼容检测设备，近年来倍受人们的关注。在混响室的设计过程中，材料的选择是其中的关键环节之一。通过仿真计算，从电场强度大小和电场均匀性两个方面研究了四种不同电导率材料对混响室场性能的影响。数据结果表明，随着材料电导率的升高，混响室内电场强度的各分量最大值和电场强度平均值均明显提高，并且材料电导率的变化不改变室内电场的分布情况。从电场均匀性方面来看，四种不同电导率材料的混响室，其电场均匀性均满足标准IEC61000-4-21的要求。     

公安武警边防部队非对称力量作战战法研究

在和平时期，各国武装警察的基本任务是打击各种违法犯罪活动。但是，各种反人类的违法犯罪活动是一种极少数人的行为，违法犯罪分子与武装警察的作战必然是一种非对称力量对抗的特殊作战。面对这种客观存在的非对称力量作战，公安武警边防部队要深入研究此条件下作战的基本战法。     

弹底引信许用旋卸扭矩的可靠性设计

分析了弹底引信旋卸时的应力分布特点,给出了应力分布规律已知时,引信不发生破坏的可靠度与最大许用旋卸扭矩之间的函数关系式,并将此式中的积分区间化为有限区间,使之能够用数值积分的方法求解。当应力分布规律未知时,假定所有被旋卸的引信都承受了同一最大应力,这样根据应力-强度干涉模型即可方便地求出其可靠度或最大许用扭矩。这两种计算方法也适用于其它螺纹连接件的旋卸可靠性分析。     

应用应力-强度干涉理论确定火炮零件的可靠性安全系数

本文根据应力—强度干涉理论,确定了火炮零件在统计意义下的可靠性安全系数并给出了可靠性安全系数的计算方法。将强度、应力、结构和可靠性计算联系起来。     

活性粉末混凝土200（RPC200）的配制试验研究

进行了活性粉末混凝土(RPC)的配制试验,通过5批试件分别探讨砂灰比、石英粉、硅灰、水胶比和钢纤维等因素单值变化时对RPC流动度以及抗折强度、抗压强度的影响.研究表明:在常规制作工艺条件下,配制出抗压强度和抗折强度分别为145.6 MPa和26.68MPa的无纤维RPC;当钢纤维含量为6%时,RPC的抗压强度和抗折强度分别达到了201.3MPa和73.67 MPa.