T300和JC2#纤维增强C/SiC复合材料力学性能对比

以聚碳硅烷(PCS)为先驱体,采用聚合物浸渍裂解法(PIP)分别制备得到T300碳纤维和JC2#碳纤维增强C/SiC复合材料。JC2#C/SiC复合材料具有优异的力学性能,抗弯强度和断裂韧性分别达到662MPa和19.5MPa.m1/2;T300 C/SiC复合材料表现出低强度、高脆性,其抗弯强度和断裂韧性不足前者的四分之一。T300 C/SiC复合材料低性能的根本原因在于T300纤维在PCS裂解过程中性能严重下降,复合材料中纤维与基体间存在强界面结合是另一个影响因素。     

基于进化规划的RBF网络用于二相码旁瓣优化

研究了低截获概率技术中常用的二相编码信号处理中的距离旁瓣压缩问题,采用改进的进化规划算法优化径向基函数网络,提出了一种基于改进进化规划算法的计算方法。通过对13位巴克码和31位M编码的仿真实验,表明新的方法在旁瓣抑制能力和运算速度等性能方面,都有较大的提高。     

基于i.MX6无人机视频码率受控的压缩系统设计

针对无人机数据链视频数据信道带宽受限要求,采用飞思卡尔i.MX6的嵌入式视频处理硬件平台,设计无人机视频H.264压缩码率受控系统,解决压缩编码的运动估计搜索范围、最大关键帧间距问题,在数据传输中采用SPI接口缓冲区码率控制机制,控制系统SPI输出码率受限的设计。实验测试表明,设计的视频处理系统视频压缩数据受控,可根据无人机无线信道设计要求,完成无人机视频压缩编码码率可控视频传输。     

Effect of nano powder (Al2O3-CaO) addition on the mechanical properties of the polymer blend matrix composite

This work describes the preparation and study of the properties of composite nanoparticles prepared by the sol-gel method which consists of two materials (Al₂O₃-CaO), and study the effect of these nanoparticles on the mechanical behavior of a polymer blend (EP 4% + 96% UPE). The powder was evaluated by X-ray diffraction analysis, scanning electron microscopy analysis (SEM), particle size analysis, and energy dispersive X-ray analysis (EDX). The mechanical behavior of the composite material was assessed by tensile test, bending test and hardness test. The evaluation results of the composite nanoparticles showed good distribution of the chemical composition between aluminum oxide and calcium oxide, smoothness in particles' size at calcination in high and low temperatures, formation of different shapes of nanoparticles and different (kappa and gamma) phases of the Al₂O₃ particles. The results of mechanical behavior tests showed marked improvement in the mechanical properties of the resulted composite material, especially at 1.5%, compared with polymer blend material without nano powder addition. The tensile properties improved about (24 and 14.9) % and bending resistance about (23.5 and 16.8) % and hardness by (25 and 22) % when adding particles of size (63.8 and 68.6) respectively. Therefore, this reflects the efficiency of the proposed method to manufacture the nanocomposite powder and the possibility of using this powder as a strengthening material for the composite materials and using these composite materials in bio applications, especially in the fabrication of artificial limbs.     

The effect of sintering and cooling process on geometry distortion and mechanical properties transition of PTFE/Al reactive materials

In this research, the effect of the sintering and cooling process on geometry distortion and mechanical properties of PTFE/Al reactive material is investigated. Six particularly selected sintering temperatures, three different cooling modes (annealing cooling, normalizing cooling and rapid cooling), three different initial cooling temperatures, as well as six different final cooling temperatures were designed to compare the effects of sintering temperature, cooling rate, initial cooling temperature and final cooling temperature on the properties of reactive materials. Geometry distortion was quantitatively analyzed by a statistic on the dimensional changes of the specimens and microscopic morphology. A mechanical response properties transition from brittle to ductile was found and analyzed. By combining the thermodynamic properties of PTFE and unsteady heat conduction theory, mechanisms of cooling induced morphology change, temperature induced distortion and strength decrease were obtained. The results showed that the cooling rate has the most significant effect on the morphology transformation, while initial cooling temperature has more significant effect on the dimensional distortion than final cooling temperature. As to the mechanical properties transition from brittle to plastic, a more prominent effect of initial cooling temperature than cooling rate and final temperature was revealed.     

酚醛-石英混杂纤维增强苯并噁嗪复合材料高温失效特征

通过模压工艺制备了酚醛-石英混织纤维增强苯并噁嗪复合材料(P-Q/BZ)试样,考察了其力学性能、烧蚀性能和耐冲刷性能,分析了该试样在高温环境中的主要失效特征,研究其在高温环境中的适用性。结果表明,未经热处理的P-Q/BZ试样平均弯曲强度、弯曲模量和层间剪切强度分别为283 MPa、10.8 GPa和22.6 MPa;经300℃,N_2处理15 min后,试样均匀膨胀,厚度增加22%,弯曲强度、弯曲模量和层间剪切强度分别下降58%、41%和58%;在氧乙炔焰的平均质量烧蚀率和线烧蚀率分别为0.048 4 g/s和-0.081 mm/s,烧蚀后试样宏观不分层,表面炭层微观分层严重,酚醛纤维热解炭、树脂基体热解炭、熔融石英纤维以及碳硅氧化产物相互分离;该试样耐冲刷能力差,在发动机尾焰烧蚀平台模拟的热-力耦合环境中的质量损失率高达59%。P-Q/BZ复合材料需要解决热解膨胀问题,进一步提高抗冲刷性能。     

深紫外非线性晶体KBe_2BO_3F_2的光学倍频特性

通过理论模拟计算详细分析了KBe2BO3F2（KBBF）晶体的光学倍频特性,得到了Nd∶YVO4激光6倍频输出的深紫外激光光源（177.3 nm）的相关技术参数。结果对于KBBF晶体用于产生深紫外全固态激光（DPL）的实验研究提供了重要的理论依据。     

多弧离子镀CrNx涂层的工艺与摩擦磨损性能

为了改善发动机活塞环的摩擦学性能和提高其使用寿命,采用多弧离子镀技术在活塞环表面制备了不同N2含量和弧电流的CrNx硬膜,采用X射线衍射技术、扫描电子显微镜、纳米硬度仪和发动机台架试验装置,分别测试了薄膜相结构、表面形貌、纳米硬度和抗高温摩擦磨损性能。研究结果表明：当N2质量分数为45%时,薄膜纳米硬度相对较高,CrNx薄膜中主要以CrN（220）相为主;随着弧电流的增加,薄膜的表面颗粒尺寸增加,当弧电流为60A时,薄膜纳米硬度相对较高。与Cr电镀层活塞环相比,CrNx涂层活塞环具有较强的抗高温粘着磨损性能。     

小波变换在雷达视频压缩中的应用

针对工程应用中雷达视频数据量大、难于实时传输的问题,分析了雷达视频数据的信息冗余和信号相关等特点,提出了一种基于小波变换的雷达视频数据压缩算法,并用该算法对实际采集的某型雷达视频数据进行压缩、解压缩处理。结果表明:该算法具有较高的压缩比和较好的信号恢复质量,具有一定的实用价值。     

面向异常检测的高光谱图像压缩技术

异常检测已经成为高光谱图像重要的后续应用之一,提出了一种面向异常检测的高光谱图像压缩算法.为减少压缩对异常检测性能的影响,首先采用RX算子对高光谱图像进行异常检测,并对异常点与背景对应的光谱维矢量进行预处理.对高光谱图像的光谱维矢量进行KL变换,通过引入虚拟维数估计算法对原始数据的本征维数进行估计,在此基础上给出了一种主分量选取方法.最后,采用最优码率分配策略为各主分量分配相应的压缩码率,并利用SPIHT算法分别进行压缩.实验结果表明,该算法在获得较高压缩性能的同时,可有效保持图像中的异常信息.