白炽灯对棉质材料的引燃性能研究

通过对不同功率白炽灯引燃100％棉质材料的研究，分析了白炽灯引燃棉质材料引发火灾的危险性。利用半导体点温计分别对不同功率白炽灯表面及棉布的温度进行记录，根据温度随时间的变化情况、可燃物被引燃情况，分析了不同功率白炽灯对棉布的引燃性能。     

吸湿环境对石英纤维增强环氧树脂面板/PMI泡沫夹层结构复合材料吸湿行为的影响

研究了不同温度、湿度环境下,夹层结构石英纤维增强环氧树脂面板/PMI泡沫夹层结构复合材料及其芯材和面板的吸湿规律。将石英纤维增强环氧树脂面板、PMI泡沫、复合材料面板/PMI泡沫夹层结构试样在不同吸湿环境中进行吸湿处理后,对其吸湿行为进行分析。结果表明:浸水环境下面板、PMI泡沫、PMI泡沫夹层结构复合材料都表现出更为严重的吸湿行为;在潮湿环境中,50℃至70℃范围内,温度越高,试样在吸湿过程中的质量损失越多,最终的饱和吸湿率越小;在60℃以内的潮湿环境中,PMI泡沫夹层结构复合材料的饱和吸湿率可以通过相同环境下面板复合材料和PMI泡沫的吸湿率进行预测。     

钢筋混凝土楼板耐火当量时间研究

从隔热性方面研究钢筋混凝土楼板的耐火极限，以室内火灾轰燃后的房间热平衡和热传导理论为基础，以钢筋混凝土楼板火灾中背火面的最高温度相等为原则，用计算机数值分析方法计算出楼板的隔火当量时间，并用最小二乘法回归出当量时间关于火灾荷栽密度和开口因子的计算公式，结果可使设计方法得到简化，为性能化耐火设计提供一定的参考。     

Effects of jute fibre content on the mechanical and dynamic mechanical properties of the composites in structural applications

Due to notable characteristics, sustainability concept and environmental issues, hybridisation natural with synthetic fibres to fabricate composites have been rapidly gaining market share in different applications (structural, military, aerospace and automotive vehicles). Compression, tension and fatigue tests of various stacking sequences of plain jute/carbon reinforced (PVB) polyvinyl butyral by hot hydraulic press technique were experimentally conducted. Six types of fabricated composites with various constituents (jute, carbon and their hybrids) were fabricated and tested. Notably, fatigue lifetime of hybrids increases with increasing the carbon content relative to the jute fibre content. On the other hand, Jute composites possess high strain compared to pure carbon composite, which gives an overall improvement in mechanical behaviours. Interestingly, H1 hybrid with Carbon/Jute/Carbon sequences offers similar fatigue stiffness behaviour of H3 hybrid with Carbon/Jute/Carbon/Jute sequences when subjected to cyclic loading. Carbon composite (C) exhibited the highest fatigue resistance, whiles jute composite (J) possessed the highest strain and semi brittle trends in both mechanical and fatigue performance. Results concluded that plain jute fibres could partially replace high-cost synthetic carbon fibres to produce more eco-friendly hybrids to be utilised in different composites industries.     

钢筋混凝土构件中钢筋温度数值计算方法讨论

采用有限元法计算构件截面温度时认为构件材料全部是混凝土,忽略了占截面积比率很小的钢筋,然后以钢筋所在位置的混凝土温度代替为钢筋的温度。人们对这种算法存在的误差大小并不清楚。对400mm×400mm矩形截面钢筋混凝土柱在四面受火条件下的温度场进行了计算,对比了考虑截面上存在钢筋时构件的温度场与不考虑钢筋而认为材料全部是混凝土时构件的温度场。研究发现,当考虑截面上存在钢筋时所得钢筋温度与采用简化方法所得替代温度差别不大,对构件承载力影响很小,说明这种简化的温度场计算方法安全可靠。