量子环流理论研究富勒烯分子的磁学性质

在原子轨道线性组合方法中引进规范变换,推导出在外加恒定磁场下分子中的电子环流表达式,应用该理论导出了分子磁化率的一般公式,并对Ｃ６０和Ｃ７０分子中π电子的磁化率进行了计算。     

zn及Zn／Si02复合添加剂的摩擦学性能

实验室自制了锂基润滑脂,通过四球试验研究zn作为锂基润滑脂添加剂在不同工况条件的摩擦学性能,利用光学显微镜和EDX分析了磨斑表面形貌及元素组成,探讨了zn的润滑作用机理,并对zn与SiO2不同复配方案的摩擦学性能进行了研究。结果表明：在低载荷条件,zn能更显著地提高锂基润滑脂的抗磨性能;在中高载荷条件,zn同时具有减摩抗磨性能,但对Pn值的提高没有太大帮助。EDX能谱分析表明磨斑表面存在特征zn元素,说明zn能够在摩擦表面沉积,形成摩擦学性能显著的表面润滑层;同时,zn与硬质颗粒SiO2在适宜的复配比例时具有一定的协同效应,能提高锂基润滑脂的摩擦学性能．     

先驱体转化致密碳化硅纳米复合材料的制备及其热电性能

以聚碳硅烷和锑改性聚硅烷为先驱体,利用先驱体转化Si C材料的富余自由碳高温石墨化的微观结构演变特点,采用热压烧结、先驱体浸渍-裂解法以及退火工艺制备出先驱体转化Si C纳米复合材料。采用SEM、TEM、XRD和Raman等测试手段表征和分析了相组成和微观结构,讨论了样品的热导率、电导率和塞贝克系数等热电参数随温度变化关系。研究表明,所得致密Si C纳米复合材料为n型热电材料。由于纳米石墨的作用,材料热导率抑制在4~8W/(m·K)范围。1600℃退火处理能够降低热导率,同时提高电导率和塞贝克系数绝对值,使先驱体转化法得到的Si C纳米复合材料无量纲热电优值ZT达到0.0028(650℃),高于其他已报道的致密Si C/C复合材料和纳米复合材料体系。     

MgO细度对磷酸镁水泥性能的影响

通过将MgO球磨0,10,20,30,60 min,制备出不同细度的MgO,考察不同细度的MgO对磷酸镁水泥净浆强度、凝结时间、流动度、水化温度和收缩性能的影响.结果表明MgO颗粒存在最佳级配体系;要保证施工的可操作时间和良好的流动性,MgO颗粒比表面积应控制在1 700～1 800 cm2/g,中值粒径控制在85～90 μm;对磷酸镁水泥温度峰值起决定作用的是小于20 μm的MgO颗粒;改变MgO颗粒的级配可以降低磷酸镁水泥的收缩率,改善体积稳定性.     

浅谈科学发展观的四个理论特性

学习实践科学发展观,是党的十七大作出的重大战略决策,是用中国特色社会主义理论体系武装全党的重大举措。全面、准确地掌握科学发展观的内涵,必须正确认识和把握科学发展观的理论特性,努力在学深学透、把握精髓,结合实际、推动工作。改造思想、坚持党性,解放思想、更新观念上下功夫,见成效,使之成为推动院校又好又快发展的基本遵循。     

3mm波段混凝土屏蔽材料的研究

在混凝土中添加标准砂,钢纤维,铁晶矿砂,炭纤维毡,氧化锌晶须,铁氧体,乙炔碳黑,羰基铁粉等材料,制成了具有微波吸收性能的混凝土屏蔽材料,以期能探索一条大型建筑及军事掩体的电磁防护的新途径。在3mm波段范围内对混凝土屏蔽材料进行了初步的实验研究,研究了不同材料、不同掺量下电磁波的吸收衰减特性,并分析了它们之间的关系,为进一步的研究指明了方向。     

T300和JC2#纤维增强C/SiC复合材料力学性能对比

以聚碳硅烷(PCS)为先驱体,采用聚合物浸渍裂解法(PIP)分别制备得到T300碳纤维和JC2#碳纤维增强C/SiC复合材料。JC2#C/SiC复合材料具有优异的力学性能,抗弯强度和断裂韧性分别达到662MPa和19.5MPa.m1/2;T300 C/SiC复合材料表现出低强度、高脆性,其抗弯强度和断裂韧性不足前者的四分之一。T300 C/SiC复合材料低性能的根本原因在于T300纤维在PCS裂解过程中性能严重下降,复合材料中纤维与基体间存在强界面结合是另一个影响因素。     

Effect of nano powder (Al2O3-CaO) addition on the mechanical properties of the polymer blend matrix composite

This work describes the preparation and study of the properties of composite nanoparticles prepared by the sol-gel method which consists of two materials (Al₂O₃-CaO), and study the effect of these nanoparticles on the mechanical behavior of a polymer blend (EP 4% + 96% UPE). The powder was evaluated by X-ray diffraction analysis, scanning electron microscopy analysis (SEM), particle size analysis, and energy dispersive X-ray analysis (EDX). The mechanical behavior of the composite material was assessed by tensile test, bending test and hardness test. The evaluation results of the composite nanoparticles showed good distribution of the chemical composition between aluminum oxide and calcium oxide, smoothness in particles' size at calcination in high and low temperatures, formation of different shapes of nanoparticles and different (kappa and gamma) phases of the Al₂O₃ particles. The results of mechanical behavior tests showed marked improvement in the mechanical properties of the resulted composite material, especially at 1.5%, compared with polymer blend material without nano powder addition. The tensile properties improved about (24 and 14.9) % and bending resistance about (23.5 and 16.8) % and hardness by (25 and 22) % when adding particles of size (63.8 and 68.6) respectively. Therefore, this reflects the efficiency of the proposed method to manufacture the nanocomposite powder and the possibility of using this powder as a strengthening material for the composite materials and using these composite materials in bio applications, especially in the fabrication of artificial limbs.     

The effect of sintering and cooling process on geometry distortion and mechanical properties transition of PTFE/Al reactive materials

In this research, the effect of the sintering and cooling process on geometry distortion and mechanical properties of PTFE/Al reactive material is investigated. Six particularly selected sintering temperatures, three different cooling modes (annealing cooling, normalizing cooling and rapid cooling), three different initial cooling temperatures, as well as six different final cooling temperatures were designed to compare the effects of sintering temperature, cooling rate, initial cooling temperature and final cooling temperature on the properties of reactive materials. Geometry distortion was quantitatively analyzed by a statistic on the dimensional changes of the specimens and microscopic morphology. A mechanical response properties transition from brittle to ductile was found and analyzed. By combining the thermodynamic properties of PTFE and unsteady heat conduction theory, mechanisms of cooling induced morphology change, temperature induced distortion and strength decrease were obtained. The results showed that the cooling rate has the most significant effect on the morphology transformation, while initial cooling temperature has more significant effect on the dimensional distortion than final cooling temperature. As to the mechanical properties transition from brittle to plastic, a more prominent effect of initial cooling temperature than cooling rate and final temperature was revealed.     

酚醛-石英混杂纤维增强苯并噁嗪复合材料高温失效特征

通过模压工艺制备了酚醛-石英混织纤维增强苯并噁嗪复合材料(P-Q/BZ)试样,考察了其力学性能、烧蚀性能和耐冲刷性能,分析了该试样在高温环境中的主要失效特征,研究其在高温环境中的适用性。结果表明,未经热处理的P-Q/BZ试样平均弯曲强度、弯曲模量和层间剪切强度分别为283 MPa、10.8 GPa和22.6 MPa;经300℃,N_2处理15 min后,试样均匀膨胀,厚度增加22%,弯曲强度、弯曲模量和层间剪切强度分别下降58%、41%和58%;在氧乙炔焰的平均质量烧蚀率和线烧蚀率分别为0.048 4 g/s和-0.081 mm/s,烧蚀后试样宏观不分层,表面炭层微观分层严重,酚醛纤维热解炭、树脂基体热解炭、熔融石英纤维以及碳硅氧化产物相互分离;该试样耐冲刷能力差,在发动机尾焰烧蚀平台模拟的热-力耦合环境中的质量损失率高达59%。P-Q/BZ复合材料需要解决热解膨胀问题,进一步提高抗冲刷性能。