基于变结构方法的空空导弹鲁棒逆控制律设计

为克服动态逆控制严重依赖被控对象精确数学模型且鲁棒性较差的缺点,将动态逆与变结构方法相结合采用双环结构设计了空空导弹鲁棒动态逆控制律.将导弹飞行状态划分成快慢2个回路,慢回路(外环)采用变结构控制,并设计扩张状态观测器,对外环中的不确定性进行估计;快回路(内环)采用动态逆控制.仿真结果表明,所设计的控制律具有较好的动态特性和鲁棒性能.     

Sandwich structure for enhancing the interface reaction of hexanitrohexaazaisowurtzitane and nanoporous carbon scaffolds film to improve the thermal decomposition performance

Improving the thermal decomposition performance of hexanitrohexaazaisowurtzitane (CL-20) by appropriate methods is helpful to promote the combustion performance of CL-20-based solid propellants. In this study, we synthesized a sandwich structure of CL-20 and nanoporous carbon scaffolds film (NCS) and emphatically studied the thermal decomposition performance of the composite structure. Thermogravimetric analysis and differential scanning calorimetry were used to measure the thermal decomposition process of the composite structure. The kinetic parameters of thermal decomposition were calculated by the thermal dynamic analysis software AKTS. These results showed that the thermal decomposition performance of the sandwich structure of CL-20 and NCS was better than CL-20. Among the tested samples, NCS with a pore size of 15 nm had the best catalytic activity for the thermal decomposition of CL-20. Moreover, the thermal decomposition curve of the composite structure at the heating rate of 1 K/min was deconvoluted by mathematical method to study the thermal decomposition process. And a possible catalytic mechanism was proposed. The excellent thermal decomposition performance is due to the sandwich structure enhances the interface reaction of CL-20 and NCS. This work may promote the extensive use of CL-20 in the field of solid rocket propellant.     

Thermal hazard assessment of TKX-50-based melt-cast explosive

In the present study, thermal hazards of TNT and DNAN used as the molten binder in TKX-50-based melt-cast explosives were comparatively studied through accelerating rate calorimeter (ARC) and Cook-off experiments. Two kinds of ARC operation modes were performed to investigate the thermal safety performance under adiabatic conditions (HWS mode) and constant heating (CHR mode). The obtained results demonstrated that at both heating modes, DNAN/TKX-50 outperformed TNT/TKX-50 from the thermal safety point of view. However, the sensitivity to heat of the samples was reverse because of the different heating modes. In addition, the results of thermal hazard assessment obtained from the cook-off experiment complied with ARC analysis which indicated the molten binder TNT replaced by DNAN would reduce the hazard of the TKX-50 melt cast explosive. Furthermore, the results of cook-off experiments also showed that DNAN/TKX-50 outperformed TNT/TKX-50 from the aspect of thermal stability, which was consistent with the result of CHR mode because of the similar heating process.     

Formation of adiabatic shearing band for high-strength Ti-5553 alloy: A dramatic thermoplastic microstructural evolution

By using split Hopkinson pressure bar, optical microscopy and electronic microscopy, we investigate the influence of initial microstructures on the adiabatic shear behavior of high-strength Ti–5Al–5V–5Mo–3Cr (Ti-5553) alloy with lamellar microstructure and bimodal microstructure. Lamellar alloy tends to form adiabatic shearing band (ASB) at low compression strain, while bimodal alloy is considerably ASB-resistant. Comparing with the initial microstructure of Ti-5553 alloy, we find that the microstructure of the ASB changes dramatically. Adiabatic shear of lamellar Ti-5553 alloy not only results in the formation of recrystallized β nano-grains within the ASB, but also leads to the chemical redistribution of the alloying elements such as Al, V, Cr and Mo. As a result, the alloying elements distribute evenly in the ASB. In contrast, the dramatic adiabatic shear of bimodal alloy might give rise to the complete lamination of the globular primary α grain and the equiaxial prior β grain, which is accompanied by the dynamic recrystallization of α lamellae and β lamellae. As a result, ASB of bimodal alloy is composed of α/β nano-multilayers. Chemical redistribution does not occur in ASB of bimodal alloy. Bimodal Ti-5553 alloy should be a promising candidate for high performance armors with high mass efficiency due to the processes high dynamic flow stress and excellent ASB-resistance.     

基于价值工程的装备体系建设费用结构优化方法研究

科学、合理地配置费用对于加强装备体系建设、提高军队战斗力具有重要的现实意义。文章介绍了价值工程的基本原理,建立了基于价值工程的装备体系建设费用结构优化模型,并引入强制确定(Forced Decision)法,通过实例讨论了优化方法的可行性和实用性。     

浅析信息化体系结构在潜艇装备维修保障中的应用

分析了武器装备维修保障信息化的基本内涵,阐述了信息化体系结构的基本概念,在分析目前主流的信息化体系结构的基础上,对构建潜艇武器装备维修保障信息化体系结构需要解决的主要问题进行论述,并给出基于美国国防部体系结构框架规范的潜艇武器装备维修保障信息化业务活动模型。     

命中角对防护结构口部爆炸毁伤影响的数值分析

为研究装药命中角对防护结构口部爆炸毁伤的影响规律,对直墙拱结构进行了一系列爆炸模拟分析,得到了直墙拱结构拱顶、拱脚和直墙底3个位置的爆炸应力和位移时程曲线。通过分析这3个位置的应力峰值和位移峰值,发现随着装药命中角的增大,拱顶处竖直方向荷载减小,而拱脚处水平方向荷载增大;随着装药命中角的增大,拱顶处竖直方向位移变形减小,而拱脚处水平方向位移变形增大。模拟分析得到的命中角对防护结构口部爆炸毁伤的影响规律,可供防护工程设计时参考。     

基于复杂网络的联合作战指挥网络拓扑结构

以复杂网络理论为基础,对联合作战指挥网络进行拓扑抽象,将指挥机构视为网络的节点,将指挥关系视为网络的边,构建了传统树状指挥网络模型、增加同级边互联的改进型指挥网络模型和不同层级边互联的交叉互联型指挥网络模型。并分析了三种网络的网络特性,以网络化效能系数（ CNE）作为度量指标,对三种网络抗毁性进行了比对分析,指出了未来联合作战指挥网络体系需要具备的特征,对探索信息化条件下高效的联合作战指挥进行了有益的探索。     

基于双滑模变结构的旋转靶弹双通道控制

针对旋转靶弹低空飞行姿态难以快速调整以及参数摄动的问题,基于内外环的双滑模变结构方法,设计了旋转靶弹的双通道控制器。基于非线性模型,对靶弹快速变化的攻角和侧滑角以及慢速变化的高度和偏航距离分别设计了一种积分型滑模面,并采用指数趋近律减轻系统的抖振,利用Lyapunov稳定理论证明其稳定性。非线性仿真结果表明,该设计控制方法能快速准确响应控制指令,且在参数摄动时表现出较强的鲁棒性。     

多尺度PCA-HOG遥感异源图像匹配算法

针对遥感异源图像匹配中非线性灰度畸变和强噪声干扰问题,提出一种基于主成分分析(Principal Components Analysis,PCA)和方向梯度直方图(Histogram of Oriented Gradients,HOG)的遥感异源图像匹配算法.该算法利用HOG提取图像间的几何结构共性特征,能有效克服异源...