分段计算方法在模拟爆炸应力波传播中的运用

针对爆炸加载下岩石响应的不同特点以及动力有限元和传统地震波模拟方法的局限性,提出了一种分段计算的数值模拟方法.该方法在空间上将所模拟的区域划分为非弹性段和弹性段,非弹性段内采用动力有限元计算方法,弹性段内采用传统的地震波方法,不同段之间以节点位移为边界条件.不同算法的数值模拟结果验证了分段计算方法用于模拟爆炸荷载产生地震波的有效性和正确性.     

岩土崩塌冲击作用下埋地管道应力与变形分析

基于散体极限平衡条件,利用马斯顿提出的沟内埋管垂直土压力计算模型,对存在冲击荷载情况的埋地管道受力进行分析,同时根据弹性半空间理论对落石冲击荷载情况下管道轴向附加荷载分布情况进行了计算分析。在利用传统的应力设计进行分析校核的同时,应用竖向变形量设计理念,研究了落石垂直冲击管道正上方时管道变形情况,以此来判断管道失效与否,为地质崩塌灾害易发区埋地管道的铺设方式提供理论和实践依据。     

悬臂式围护桩受力性状与内力传递特征试验

为研究悬臂式围护桩结构的内力、弯矩、位移和嵌固段的变化规律及特点,结合西宁火车站综合改造工程,对该深基坑支护结构在不同开挖工况条件下悬臂桩的受力性状与内力传递特征进行现场动态测试试验。试验结果表明:悬臂桩的受力特征与理论值有所差异,在实际设计中可对其在配筋方式、混凝土强度设计、嵌固段长度等方面进行优化。试验结果可以有效优化桩身设计,为复杂基坑在开挖过程中的支护结构受力及变形提供参考性依据。     

ORGANISING THE BLUES

While all governments in the region acknowledge the importance of the work of police officers, they seldom take a close look at their working conditions and the nature of police labour. While the situations in Namibia, Zimbabwe, Zambia, Lesotho and Swaziland are different there are commonalities: police management has not changed significantly and neither has police legislation. Key concerns of the officers in the region centre on service conditions and wages. Communicating these concerns to the state is made difficult by the less than democratic approach taken by governments professing to favour democratization. A more democratic workplace for the police is of benefit to the broader community and is a crucial point to bear in mind when attempting to develop community-oriented professional policing.     

基于步进加速寿命试验的制导弹药储存寿命评估

介绍步进应力加速寿命试验原理,通过对制导弹药自动导引头贮存状态和失效机理的分析,确定了加速寿命试验应力和应力水平．假设产品寿命服从威布尔分布,应用极大似然估计和Bayes的方法处理数据,建立制导弹药可靠储存寿命预测模型,并计算得到自动导引头在正常应力水平下的可靠储存寿命．     

位移不连续法在裂纹扩展仿真中的应用

探讨了在应用位移不连续法仿真裂纹扩展时对加载方式、裂纹扩展长度及应力强度因子计算等问题的处理方法,并据此编制了仿真程序,分析了裂纹在单向压载作用下的扩展趋势和应力变化,具有一定的工程应用价值。     

燃烧室压力对潜入式喷管喉衬热应力的影响

为了研究燃烧室压力对固体火箭发动机潜入式喷管热应力影响规律的问题,采用商业流体软件,基于压力求解器,求解了喷管纯气相的流场,确定了燃气温度、压力、壁面对流换热系数;采用有限元软件,依据流场计算的非均布壁面压力与非均布对流换热,求解了燃烧室压力为6 MPa下的潜入式喷管热结构问题;通过地面点火试验验证了仿真模型与数值方法的有效性与准确性;采用相同计算模型与数值方法,求解了在燃烧室压力为9 MPa、12 MPa下的喷管热结构问题,揭示了燃烧室压力对喉衬热应力的影响规律。结果表明:整个工作过程,喉衬环向应力最大值为103.9 MPa,位于内表面,且随时间增大,先增大后减小;喉衬环向拉应力也随时间先增大后减小;随压力增大,对流换热系数增大,喉衬温度升高,喉衬环向拉应力增大,喉衬环向压应力减小。     

Influences of different crossing types on dynamic response of underground cavern subjected to ground shock

An intersecting cavern is a common structural form used in underground engineering, and its safety and stability performance directly control the service performance of the whole project. The dynamic re-sponses of the three kinds of crossing type (+-shaped, T-shaped, L-shaped) caverns subjected to ground shock were studied by numerical simulation. The velocity plus force mode boundary setting method was proposed in the coupled static and dynamic analysis of a deep underground cavern. The results show that, among the three types of crossing caverns, the+-shaped cavern is the most significantly affected by the dynamic action, followed by T-shaped, and then L-shaped caverns. The vault settlement, straight wall deformation, vault peak particle velocity, effective plastic strain of surrounding rock, and maximum principal stress and strain at the bottom of the lining of the straight wall increase with the increase of cavern span. The vault settlement, straight wall deformation, effective plastic strain of surrounding rock, and the maximum principal stress and strain at the bottom of lining to the straight wall decrease with the increase of lateral pressure coefficient, and the peak particle velocity at the vault increases. The variation is small compared with the change of cavern span. The influence range of the underground cavern intersection is two cavern diameters from the intersection centre. The bottom of the straight wall at the intersection is the weak part. It is suggested to thicken the support locally to improve the stability of the cavern.     

Effect of friction stir processing on mechanical properties and heat transfer of TIG welded joint of AA6061 and AA7075

Tungsten inert gas (TIG) welding is the most commonly used joining process for aluminum alloy for AA6061 and AA7075 which are highly demanded in the aerospace engineering and the automobile sector, but there are some defects occur during TIG welding like micro-crack, coarse grain structure, and porosity. To improve these defects, the TIG welded joint is processed using friction stir processing (FSP). This paper presents the effect of friction stir processing on TIG welding with filler ER4043 and ER 5356 for dissimilar aluminum alloy AA6061 and AA7075. The mechanical characterization, finite element formulation and mathematical equations of heat transfer of TIG + FSP welded joints are investigated using ANSYS Fluent software by adjusting process parameters of FSP. The results show that the maximum compressive residual stress 73 MPa was obtained at the fusion zone (FZ) of the TIG weldment with filler ER4043, whereas minimum compressive residual stress 37 MPa was obtained at stir zone (SZ) of the TIG+FSP with filler 5356. The maximum heat flux 5.33 × 106 W/m2 and temperature 515 ℃ have observed at tool rotation 1600 rpm with a feed rate of 63 mm/min. These results give a satisfactory measure of confidence in the fidelity of the simulation     

自润滑弹带挤进过程中渗出油量的对比计算

从弹带的作用及特性出发, 通过数值计算和统计计算 2种方法计算了自润滑弹带挤进过程中的渗出油量,初步得出了渗出油量和行程之间的关系。这一问题的解决为自润滑弹带材料的选择提供了理论依据。通过对 2种算法的比较可知, 数值计算误差更小一些, 而统计计算对数学条件要求不太苛刻。