空化射流实验研究

空化水射流技术是将空化作用引入到高压水射流而形成的一种新型高压水射流技术，在同等条件下，空化射流相对于普通高压水射流具有破碎和切割能力更高的特点。通过数值模拟和实验方法对空化技术进行研究，进行了喷嘴流场的数值模拟计算，设计了空化射流实验装置及空化喷嘴。以生锈铁板为研究对象，分别进行了喷嘴型号、打击时间、入口压力、靶距和扩散段长度的空化射流打击效果对比实验，研究了空化参数对空化效果的影响。实验结果表明角形喷嘴进行淹没射流的空化效果较好，空化射流除锈具有最优打击时间。不同的入口压力对应不同的最佳靶距。     

超低照度下微光图像增强神经网络损失函数设计分析

超低照度下(环境照度小于2×10~(-3)lux)微光图像具有低信噪比、低对比度等特点,使目标难以辨识,严重影响观察效果。为了提高超低照度下微光图像质量,设计了一种用于微光图像增强的卷积自编码深度神经网络,并针对传统的均方误差损失函数不符合人类视觉感知特性等问题,结合现有的全参考图像质量评价指标,研究了包括感知损失在内的几种损失函数,并提出了一种新的可微分损失函数。实验结果表明,在网络结构不发生改变的情况下,所提损失函数具有更好的性能,在提高微光图像信噪比和对比度的同时,能够有效地增强图像内部细节信息。     

Effect of wave shaper on reactive materials jet formation and its penetration performance

Wave shaper effect on formation behavior and penetration performance of reactive liner shaped charge (RLSC) are investigated by experiments and simulations. The reactive materials liner with a density of 2.3 g/cm³ is fabricated by cold pressing at a pressure of 300 MPa and sintering at a temperature of 380 °C. Experiments of the RLSC with and without wave shaper against steel plates are carried out at standoffs of 0.5, 1.0, and 1.5 CD (charge diameter), respectively. The experimental results show that the penetration depths and structural damage effects of steel plates decrease with increasing the standoff, while the penetration depths and the damage effects of RLSC without wave shaper are much greater than that with wave shaper at the same standoff. To understand the unusual experimental results, numerical simulations based on AUTODYN-2D code are conducted to discuss the wave shaper effect, including the propagation behavior of detonation wave, the velocity and temperature distribution of reactive jet, and penetration depth of reactive jet. The simulations indicate that, compared with RLSC without wave shaper, there is a higher temperature produced inside reactive jet with wave shaper. This unusual temperature rise effects are likely to be an important mechanism to cause the initiation delay time of reactive jet to decline, which results in significantly decreasing its penetration performance.     

单兵火箭燃气射流噪声抑制的实验研究

为了能够有效抑制单兵火箭发射时的燃气射流噪声,设计了液体水圆柱形平衡体安置在火箭发动机后面,对平衡体降噪进行实验研究。在实验中利用压电式传感器测得了发射筒周围的冲击波超压值,与没加液体水平衡体实验测得的超压值相比较,发现放液体水平衡体时在改进发动机推力性能的同时,降低了整个观测区域的噪声,尤其是射流上游,起到了显著的降噪效果,并分析了火箭燃气射流与液体水平衡体相互作用的机理。实验结果对单兵火箭发射的噪声防护问题研究提供了科学依据。     

水顶油顺序输送油水混合模型研究

顺序输送是利用一条管道输送多种油品,因其可最大限度发挥管道输送潜能而被广泛应用。按照前后行液体不同可分为水顶油、油顶水和不同油品间顺序输送等,其中水顶油顺序输送主要用于管道撤收前的排空作业。对水顶油顺序输送油水混合过程进行了分析,建立了油水混合模型,利用CFD对其进行数值求解,并将仿真结果与前期理论分析进行了对比,两者吻合较好。所得结论可为机动管线水顶油排空作业提供科学指导。     

聚能射流形成过程的理论建模与分析

分析了聚能射流的形成过程,并对其中的各阶段进行了详细建模。在模型中考虑了炸药爆轰、金属的驱动、药型罩压垮以及射流和杵体的形成过程。采用该模型对某一聚能装药结构进行了计算,计算结果表明:药型罩顶部和底部微元的压垮速度较小,在射流头部形成反向速度梯度,与试验数据吻合较好。该模型对于多级侵彻战斗部的工程设计与侵彻参数的计算具有一定的参考价值。     

L波段掺铒光纤放大器增益钳制及提高特性研究

报道了一种新型980 nm激光二极管(LD)泵浦高增益的掺铒光纤放大器(EDFA).通过加入中心波长为1 550 nm光纤光栅(FBG)可以明显提高增益,并分析了增益钳制的原理.实验得到其增益比无FBG结构EDFA提高8 dB,并得到了小信号输入时增益25 dB的有效钳制.     

汽油与柴油混合用作柴油机应急燃料的探讨

应急燃料对于提高战时油料保障能力具有重要意义。文章以在-10#军用柴油中掺入90#车用汽油(简称为汽柴混合油)为例,从柴油机燃料应具有的品质性能着手,分析了汽柴混合油作为柴油机应急燃料的可行性。把车用汽油和军用柴油按照不同的比例掺兑,将试验结果与军用柴油的性能要求和美军应急使用指标对某些理化性能的要求相比照, 指出了汽柴混合油作为柴油机燃料的可行性,并提出了建议。     

A case study in bio-inspired engineering design: defense applications of exoskeletal sensors

As part of a bio-inspired design process, the authors examine exoskeletal sensors found in insects and their potential application to armor and hardened buildings. In this way, the outer hardening of a structure or vehicle would not limit the ability of occupants to arrive at an actionable picture of the outer environment. To this end, various sensor modalities employed by insects are compared and contrasted with their current human-engineered equivalents. In several sensing modalities, biosensors perform better, are smaller, and more energy efficient than human-engineered equivalents. They note that biological designs tend to employ non-linear response to signal amplitude and respond with heightened sensitivity over a greater dynamic range of signals than human-engineered sensors. The insect biological sensors have structural and mechanical innovations that preserve the protective capacity of the exoskeleton.     

采用射流掺混增强的前可调面积涵道引射器数值模拟

为了提高风扇外涵和核心机驱动风扇级外涵流体的掺混效率，提出一种采用射流掺混增强的前可调面积引射器设计方案。通过数值模拟的手段对流量特性、流动掺混和总压损失等方面进行了研究，并同基准模型进行了对比分析，结果表明：采用波瓣混合器结构的前可调面积引射器设计，显著地增加了较高出口背压工况下风扇外涵的流通能力；新的设计方案不仅没有增加低出口背压工况下的总压损失，还减小了高背压出口工况下的流动损失；流向涡的特征尺度是提高掺混效率的关键，可以进一步优化波瓣混合器几何轮廓，以满足调节机构对结构设计的要求。